Page 633 of 4378

DESCRIPTION AND OPERATION
Brake Booster —
Hydro-Boost
The Hydro- Boost brake booster is a hydraulically operated brake booster powered by the power
steering pump (3A674). The power steering pump provides the fluid pressure to operate both the
power brake booster and the power steering gear (3504).
A Hydro- Boost reserve system (accumulator) stores sufficient fluid under pressure to provide at least
two power- assisted brake applications in the event the power steering pump fluid flow is interrupted.
For low assist concerns on vehicles equipped with the Hydro- Boost system, refer to Section 211 - 00 to
check the power steering pump pressure and flow.
The brakes can also be applied manually if the reserve system is depleted.
Any leakage goes directly back to the power steering pump reservoir (3E764). SECTION 206-
07: Power Brake Actuation 2003 Mustang Workshop Manual Item Part Number Description
1 2140 Master cylinder
2 2B559 Hydro-Boost Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...
Page 634 of 4378
Klj . 2 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...
Page 635 of 4378

GENERAL PROCEDURES
Hydro-
Boost Bleeding
1. NOTE: The Hydro- Boost power brake booster (2B560) is generally self- bleeding, and the
following procedure will normally bleed the air from the power brake booster. Normal operation
of the vehicle will further remove any additional trapped air.
Fill the power steering oil reservoir (3A697) with MERCON® Multi- Purpose ATF XT-2-QDX or
MERCON® equivalent.
2. Remove the powertrain control module (PCM) fuse to prevent the engine from starting.
3. Crank the engine for several seconds.
4. Check the fluid level in the power steering oil reservoir and add if necessary. Install the powertrain control module (PCM) fuse.
5. Start the engine.
6. With the engine running, turn the steering wheel (3600) from stop- to-stop twice. Turn the engine
off.
7. Depress the brake pedal (2455) several times to discharge the accumulator.
8. Repeat Steps 5 and 6.
9. If foaming occurs, stop the engine and allow the foam to dissipate.
10. Repeat Steps 5 and 6 as required, until all the air is removed from the system (when the foaming stops).
SECTION 206-
07: Power Brake Actuation 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...
Page 636 of 4378
Klj . 2 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...
Page 637 of 4378
REMOVAL AND INSTALLATION
Brake Booster —
Vacuum
Removal 1. Disconnect the battery ground cable (14301). For additional information, refer to Section 414 -
01 .
2. Remove the air cleaner housing. For additional information, refer to Section 303 - 12 .
3. Remove the brake master cylinder nuts.
4. Position the brake master cylinder (2140) aside.
5. With the engine off, depress the brake pedal (2455) several times to discharge the accumulator. Disconnect the booster vacuum hose.
6. Remove the stoplight switch self- locking pin.
SECTION 206-
07: Power Brake Actuation 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...
Page 638 of 4378
7. Remove the stoplight switch (13480) and the brake booster push rod from the brake pedal pin.
8. Remove the power brake booster nuts.
9. Remove the power brake booster (2005).
Installation 1. Follow the removal procedure in reverse order. Klj . 2 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...
Page 639 of 4378
Klj . 3 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...
Page 640 of 4378

REMOVAL AND INSTALLATION
Brake Booster —
Hydro-Boost
Removal WARNING: The power brake booster should not be carried by the accumulator, nor
should it ever be dropped on the accumulator. Check the snap ring on the accumulator for
correct seating before the power brake booster is used. The accumulator contains high-
pressure nitrogen gas and can be dangerous if mishandled.
WARNING: If the accumulator is to be disposed of, it must not be exposed to excessive
heat. Before discarding the accumulator, drill a 1.6- mm (1/16-inch) diameter hole in the end of
the accumulator can to relieve the gas pressure. Always wear safety glasses when performing
this operation.
1. With the engine off, depress the brake pedal (2455) several times to discharge the accumulator.
2. Disconnect the battery ground cable (14301). For additional information, refer to Section 414 -
01 .
3. Disconnect the fluid level sensor connector.
4. Disconnect the brake tubes.
SECTION 206-
07: Power Brake Actuation 2003 Mustang Workshop Manual Special Tool(s)
Installer Set, Teflon Seal
211-
D027 (D90P-3517- A) or
equivalent Klj . 1 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...