Page 881 of 4378
GENERAL PROCEDURES
Crankshaft —
Connecting Rod Journal Taper, Out of Round
1. Measure the crankshaft connecting rod journal diameters in two directions perpendicular to one another at each end of the connecting rod journal. The difference in the measurements from
one end to the other is the taper. Verify measurement is within the wear limit.
zRefer to the appropriate section in Group 303 for the procedure.
z If out of specification, install new components as necessary. Refer to the appropriate
section in Group 303 for the procedure.
SECTION 303-
00: Engine System — General Information 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...
Page 882 of 4378
GENERAL PROCEDURES
Cylinder Bore —
Taper
1. Measure the cylinder bore at the top, middle, and bottom of piston ring travel in two directions as indicated. Verify the cylinder bore is within the wear limit. The difference indicates the
cylinder bore taper. Bore the cylinder to the next oversize.
zRefer to the appropriate section in Group 303 for the procedure.
SECTION 303-
00: Engine System — General Information 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...
Page 883 of 4378
GENERAL PROCEDURES
Cylinder Bore —
Out-of-Round
1. Measure the cylinder bore in two directions. The difference is the out-of- round. Verify the out-of-
round is within the wear limit and bore the cylinder to the next oversize limit.
zRefer to the appropriate section in Group 303 for the procedure.
SECTION 303-
00: Engine System — General Information 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...
Page 884 of 4378
GENERAL PROCEDURES
Piston Inspection
CAUTION: Do not use a caustic cleaning solution or a wire brush to clean the pistons or
damage can occur.
1. Clean and inspect the (1) ring lands, (2) skirts, (3) pin bosses, and the (4) tops of the pistons. If wear marks, scores or glazing is found on the piston skirt, check for a bent or twisted
connecting rod.
2. Use the Piston Ring Groove Scraper to clean the piston ring grooves. zMake sure the oil ring holes are clean.
SECTION 303-
00: Engine System — General Information 2003 Mustang Workshop Manual Special Tool(s)
Scraper, Piston Ring Groove
303-
D033 (D81L-6002- D) or
equivalent Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...
Page 885 of 4378
Klj . 2 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...
Page 886 of 4378
GENERAL PROCEDURES
Piston —
Pin to Bore Diameter
1. WARNING: Cover the end of the pin bore with a hand or shop rag when removing
the retainer ring, since it has a tendency to spring out. Wear eye protection.
NOTE: Piston and piston pins are a matched set and should not be interchanged.
Measure the piston pin bore diameter in two directions on each side. Verify the diameter is
within specification. zIf out of specification, install new components as necessary. Refer to the appropriate
section in Group 303 for the procedure.
SECTION 303-
00: Engine System — General Information 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...
Page 887 of 4378
Klj . 2 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...
Page 888 of 4378