Page 3969 of 4378
REMOVAL AND INSTALLATION
Front Bumper Cover
Removal and Installation
NOTE:
Mustang shown, GT and Cobra similar.
1. Remove the pin- type retainers and the radiator upper sight shield.
2. Remove the two pin- type retainers (one each side).
3. Remove the four front bumper cover nuts (two each side).
4. Remove the lower bumper cover pin- type retainers.
SECTION 501-
19: Bumpers 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...
Page 3970 of 4378
5. Remove the four headlamp mounting clips.
6. Disconnect the parking lamp and the headlamp electrical connectors (two each) and remove the
two headlamps.
7. Remove the pin- type retainers. 8. If equipped, remove the pin - type retainers. Klj . 2 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...
Page 3971 of 4378
9. If equipped, disconnect the fog lamp electrical connectors.
10. Lift up on the tabs and remove the front bumper cover.
11. To install, reverse the removal procedure. Klj . 3 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...
Page 3972 of 4378
REMOVAL AND INSTALLATION
Rear Bumper Cover
Removal and Installation
1. Remove the luggage compartment trim panel covers.
2. Remove the seven rear bumper cover nuts.
3. Remove the fuel drain hose.
4. Remove the four bumper cover screws (two each side).
5. Remove the pin- type retainers and the rear bumper cover.
SECTION 501-
19: Bumpers 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...
Page 3973 of 4378
6. To install, reverse the removal procedure. Klj . 2 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...
Page 3974 of 4378
REMOVAL AND INSTALLATION
Front Bumper
Removal and Installation
All vehicles except Cobra
1. Remove the front bumper cover. For additional information, refer to Front Bumper Cover in this
section.
Cobra 2. Remove the charge air cooler. For additional information, refer to Section 303 - 12 .
All vehicles 3. Remove the two rivets and the front bumper isolator.
Cobra 4. NOTE: The charge air cooler bracket is removed for clarity.
Remove the four bolts and the two intercooler radiator brackets.
All vehicles 5. Remove the bolts and the front bumper.
SECTION 501-
19: Bumpers 2003 Mustang Workshop Manual Special Tool(s)
Heavy-Duty Riveter
501-
D011 (D80L-23200- A) Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...
Page 3975 of 4378
6. To install, reverse the removal procedure. Klj . 2 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...
Page 3976 of 4378
REMOVAL AND INSTALLATION
Rear Bumper
Removal and Installation
All vehicles
1. Remove the rear bumper cover. For additional information, refer to Rear Bumper Cover in this
section.
2. Remove the rear bumper cover isolator.
Vehicles with 4.6L engines
3. Remove the bolts and the exhaust outlet pipe bumper bracket.
All vehicles 4. Remove the rear bumper brace and tongue bolts.
5. Remove the bolts and the rear bumper.
SECTION 501-
19: Bumpers 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...