Page 169 of 4378
10. Support the front suspension lower arm with a jack stand.
11. Remove the nut and the ABS sensor wire bracket.
12.
WARNING: All vehicles are equipped with gas pressurized shock absorbers which
will extend unassisted. Do not apply heat or flame to the shock absorbers during
removal or component servicing. Failure to follow these instructions can result in
personal injury.
Disconnect the front shock absorber (18124) from the spindle. 1. Remove and discard the nuts and bolts.
2. Disconnect the shock absorber.
13. Remove the spindle. 1. Remove and discard the nut.
2. Remove the spindle. Klj . 3 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...
Page 170 of 4378
Installation
1. To install, reverse the removal procedure. Klj . 4 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...
Page 171 of 4378
2. Check wheel alignment. Adjust if necessary. For additional information, refer to Section 204 - 00 . Klj . 5 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...
Page 172 of 4378

REMOVAL AND INSTALLATION
Shock Absorber
Removal
WARNING: All vehicles are equipped with gas pressurized shock absorbers which will
extend unassisted. Do not apply heat or flame to the shock absorbers during removal or
component servicing. Failure to follow these instructions can result in personal injury.
CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number or an equivalent part must be installed, if installation is necessary. Do
not use a part of lesser quality or substitute design. Torque values must be used as specified
during reassembly to ensure proper retention of these parts.
1. Raise the vehicle on a hoist. For additional information, refer to Section 100 - 02 .
2. Remove the wheel and tire assembly. For additional information, refer to Section 204 - 04 .
3. Remove the front brake disc. For additional information, refer to Section 206 - 03 .
4. Remove the bolt and the ABS sensor.
5. Unclip the ABS sensor wire from the bracket.
6. Remove the nut and the ABS sensor wire bracket.
SECTION 204-
01: Front Suspension 2003 Mustang Workshop Manual Klj . 1 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...
Page 173 of 4378
7. Support the front suspension lower arm (3078) with a jack stand.
8. Disconnect the shock absorber (18124) from the spindle (3105).
1. Remove and discard the nuts and bolts.
2. Disconnect the shock absorber.
9. Carefully lower the front suspension lower arm and remove the jack stand.
10. CAUTION: Do not allow the weight of the vehicle to rest on the front brake disc
shield. Damage to the shield can occur.
Lower the vehicle to access the upper mount nuts and bolt.
11. Remove the shock absorber. 1. Remove the bolt and nuts. Discard the nuts.
2. Remove the shock absorber.
12. Position the shock absorber in a vise. 13. Remove the nut and the front shock absorber mounting bracket (18183). Klj . 2 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...
Page 174 of 4378
14. Remove the sleeve and the bushing.
Installation 1. To install, reverse the removal procedure. Klj . 3 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...
Page 175 of 4378
Klj . 4 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...
Page 176 of 4378
Klj . 5 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...