Page 209 of 4378
5. Remove and discard the nuts from the stabilizer bar.
Installation
NOTE: Make sure the rear stabilizer bar is not installed upside down. A color code is provided on the
right (passenger) side only as an aid for correct positioning.
NOTE: Use new fasteners when installing the stabilizer bar.
1. To install, reverse the removal procedure. Klj . 2 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...
Page 210 of 4378
Klj . 3 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...
Page 211 of 4378

REMOVAL AND INSTALLATION
Stabilizer Bar —
Cobra
Removal
CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number must be installed if installation becomes necessary. If substitution is
necessary, the part must be of the same finish and property class. Torque values must be used
as specified during reassembly to make sure of correct retention of these parts.
1. Remove the rear coil springs (5560). For additional information, refer to Spring — Cobra in this
section.
2. Raise the subframe into position and remove the front bolts.
3. Lower the subframe out of the vehicle.
4. NOTE: To remove the stabilizer bar link nuts, first loosen the nut, then use the hex holding
feature to prevent the stabilizer bar link ball joint from turning while removing the nut.
Remove the nuts and the stabilizer bar links (5C488). Discard the nuts.
5. Remove the bolts and the stabilizer bar brackets (4A047). Discard the bolts.
SECTION 204-
02: Rear Suspension 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...
Page 212 of 4378
6. Remove the stabilizer bar (5A772) with the stabilizer bar bushings (5493).
Installation 1. NOTE: The stabilizer bar bracket bolts and the nuts on the stabilizer bar links are of a torque
prevailing design. New bolts and nuts must be used during installation.
NOTE: To install the stabilizer bar link nuts, first install the nuts until snug using the hex holding
feature to prevent the stabilizer bar link ball joint from turning. Final tighten the nuts using a
socket and a torque wrench.
To install, reverse the removal procedure. Klj . 2 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...
Page 213 of 4378
2. Check wheel alignment. Adjust as necessary. For additional information, refer to
Section 204 -
00 . Klj . 3 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...
Page 214 of 4378

REMOVAL AND INSTALLATION
Link —
Stabilizer Bar
Removal
CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number must be installed if installation becomes necessary. If substitution is
necessary, the part must be of the same finish and property class. Torque values must be used
as specified during reassembly to make sure of correct retention of these parts.
1. Raise the vehicle on a hoist. For additional information, refer to Section 100 - 02 .
2. NOTE: Spring is removed for clarity.
NOTE: To remove the nuts, first loosen the nut, then use the hex holding feature to prevent the
stabilizer bar link ball joint from turning while removing the nut.
Remove the nuts and the stabilizer bar links (5C488). Discard the nuts.
Installation 1. NOTE: The nuts on the stabilizer bar links are of a torque prevailing design. New nuts must be
used during installation.
NOTE: To install the nuts, first install the nut until snug using the hex holding feature to prevent
the stabilizer bar link ball joint from turning. Final tighten the nuts using a socket and a torque
wrench.
To install, reverse the removal procedure.
SECTION 204-
02: Rear Suspension 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...
Page 215 of 4378
Klj . 2 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...
Page 216 of 4378

REMOVAL AND INSTALLATION
Wheel Knuckle —
Cobra
Removal CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number must be installed if installation becomes necessary. If substitution is
necessary, the part must be of the same finish and property class. Torque values must be used
as specified during reassembly to make sure of correct retention of these parts.
1. Mark the rear shock absorber (18125) relative to the protective sleeve with the vehicle in a static, level ground position (curb height).
2. Raise the vehicle on a hoist. For additional information, refer to Section 100 - 02 .
3. Remove the wheel and tire assembly. For additional information, refer to Section 204 - 04 .
4. Remove and discard the rear hub retainer (4B477).
SECTION 204-
02: Rear Suspension 2003 Mustang Workshop Manual Special Tool(s)
Front Hub Remover
205-
D070 (D93P-1175- B) or
Equivalent Steering Arm Remover
211-
003 (T64P-9171- A) Klj . 1 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...