Page 2665 of 4378
Installation
1. NOTE: Clean the clutch pressure plate and flywheel with a commercial alcohol- based solvent
so surfaces are free from oil film. Do not use cleaners with a petroleum base.
NOTE: Before installing the transmission, the ball stud, the clutch release lever and the input
shaft must be cleaned and lubricated with grease.
To install, reverse the removal procedure.
zUsing the special tool, align the clutch disc and pressure plate to the flywheel.
2. Tighten the pressure plate bolts in two stages. zStage 1: Tighten the bolts to 45 Nm (33 lb- ft).
z Stage 2: Tighten the bolts an additional 60 degrees. Klj . 3 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...
Page 2666 of 4378
Klj . 4 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...
Page 2667 of 4378
REMOVAL AND INSTALLATION
Pilot Bearing
1. Remove the clutch disc and the clutch pressure plate. For additional information, refer to Disc and Pressure Plate — 3.8L and 4.6L (2V) Engines or
Disc and Pressure Plate — 4.6L (4V) Engine
in this section.
2. Using the special tool, remove the pilot bearing from the flywheel.
Installation 1. Insert the pilot bearing into the crankshaft.
2. Install the clutch disc and the clutch pressure plate. For additional information, refer to Disc and Pressure Plate — 3.8L and 4.6L (2V) Engines or
Disc and Pressure Plate — 4.6L (4V) Engine in
this section.
SECTION 308-
01: Clutch 2003 Mustang Workshop Manual Special Tool(s)
Puller with Slide Hammer
308-
001 (T58L-101- B) Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...
Page 2668 of 4378
Klj . 2 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...
Page 2669 of 4378

REMOVAL AND INSTALLATION
Flywheel Ring Gear
Removal
1. Remove the flywheel. For additional information, refer to Section 303 - 01A ,
Section 303 - 01B or
Section 303 - 01C .
2. WARNING: This procedure should be carried out only by a correctly equipped and
experienced acetylene torch operator. Tongs must be used or asbestos gloves worn
when handling the heated flywheel ring gear. Failure to follow these instructions can
result in personal injury.
CAUTION: Tap the flywheel ring gear evenly to prevent binding.
Remove the flywheel ring gear from the flywheel. zEvenly heat the flywheel ring gear with an acetylene torch and use a brass drift to drive
the flywheel ring gear off the flywheel.
Installation
1. WARNING: This procedure should be carried out only by a properly equipped and
experienced acetylene torch operator. Tongs must be used or asbestos gloves worn
when handling the heated flywheel ring gear. Failure to follow these instructions can
result in personal injury.
CAUTION: Do not heat the flywheel ring gear beyond 261°C (500°F). Use heat-
indicating crayons to prevent overheating.
CAUTION: Keep the torch moving to prevent hot spots.
Evenly heat the flywheel ring gear with an acetylene torch. zInstall the flywheel ring gear with the bevel on the flywheel ring gear facing the rear of the
flywheel.
z Use a brass drift to tap the flywheel ring gear into position, reheat as necessary.
2. Install the flywheel. For additional information, refer to Section 303 - 01A ,
Section 303 - 01B or
Section 303 - 01C . SECTION 308-
01: Clutch 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...
Page 2670 of 4378
Klj . 2 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...
Page 2671 of 4378
SPECIFICATIONS
SECTION 308-
02: Clutch Controls 2003 Mustang Workshop Manual General Specifications
Item Specification
Clutch System
System adjustment Self adjusting
Fluid and Lubricant
Super Premium SAE 10W-30
XO- 10W-30- BSP WSS-
M2C153- G
Torque Specifications Description Nm lb-
ft lb-
in Brake booster nuts 25 18 —
Brake pedal support bracket to cowl bolt 25 18 —
Clutch pedal retaining nut 40 30 —
Clutch release lever cable bracket screw (3.8L) 10 — 89
Clutch release lever cable to bulkhead screws 4 — 35
Clutch release lever cable to crossmember retaining screw 8 — 71
Clutch release lever cable to master cylinder retaining screw (4.6L) 8 — 71
Instrument panel reinforcement screws 9 — 80
Instrument panel steering column cover screws 9 — 80 Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...
Page 2672 of 4378
Klj . 2 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...