2003 FORD MUSTANG Workshop Manual

language fuel headlights interior lights change wheel CD changer

Page 257 of 4378

FORD MUSTANG 2003 Workshop Manual Klj . 4 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Page 258 of 4378

FORD MUSTANG 2003 Workshop Manual GENERAL PROCEDURES
Wheel Leaks
WARNING: Wheel repairs that use welding or peening are not approved. An inner tube is
not an acceptable repair for leaking wheels or tires.
If the air pressure in a

GENERAL PROCEDURES
Wheel Leaks
WARNING: Wheel repairs that use welding or peening are not approved. An inner tube is
not an acceptable repair for leaking wheels or tires.
If the air pressure in a tire mounted on an aluminum wheel is found to be low, perform the
following procedure before considering installation of a new wheel.
1. Remove the tire and wheel assembly, and inspect the wheel for structural damage. If none exists, go to Step 2. If the wheel is damaged, install a new wheel.
2. With the tire mounted on the wheel, locate the air leak using a water bath or equivalent method, and mark the location. Check the complete wheel for possible additional leaks. When leaks are
marked, dismount the tire marking valve location on the tire for correct indexing.
3. On the tire side of the wheel, thoroughly clean the leaking area with an appropriate choke cleaner or use sandpaper of approximately 80- grit to remove all contamination. Using the
sandpaper, score the surface of the leaking area to improve adhesion of the sealer. If the valve
stem is close to the area, remove it.
4. Use a clean cloth to remove all cleaner or sanding dust.
5. NOTE: Do not use a torch containing oxyacetylene.
Heat the prepared area with a Heat Gun or a propane torch until aluminum wheel repair
compound flows. Apply the hot melt material over the prepared area using a liberal flow and
wiping action. Repair is most effective when heat is applied to the brake side of the rim, and the
sealer is melted by heat in the metal.
6. Apply only enough heat to melt the sealer, then remove the heat source. After repairing the leak, allow the wheel to cool until it can be handled safety.
7. CAUTION: Use caution when mounting the tire so as not to damage the sealer.
Index and assemble the tire and wheel. Inflate the tire to the recommended pressure as
indicated on the tire pressure decal.
8. Repeat Step 2 to verify repair.
9. When the repair is completed, balance the assembly and install it on the vehicle.
SECTION 204-
04: Wheels and Tires 2003 Mustang Workshop Manual Material
Item Specification
Professional Choke and
Linkage Cleaner
F8AZ-
19520- AB WSS-
M14P10-
B Aluminum Wheel Repair
Compound ESA-
M4G280-
A Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Page 259 of 4378

FORD MUSTANG 2003 Workshop Manual Klj . 2 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Page 260 of 4378

FORD MUSTANG 2003 Workshop Manual REMOVAL AND INSTALLATION
Wheel And Tire
Removal
1. CAUTION: Do not use heat to loosen a seized wheel nut (1012). Heat can damage
the wheel and wheel bearings.
NOTE: To avoid damage or scratchin

Page 261 of 4378

FORD MUSTANG 2003 Workshop Manual Installation
1. WARNING: When a wheel is installed, always remove any corrosion, dirt or foreign
material present on the mounting surfaces of the wheel and the surface of the wheel hub,
brake drum

Page 262 of 4378

FORD MUSTANG 2003 Workshop Manual Klj . 3 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Page 263 of 4378

FORD MUSTANG 2003 Workshop Manual SPECIFICATIONS
All driveshaft and pinion angles point downward.
a
Service refill capacities are determined by filling the axle 6.3 mm (0.25 in [1/4 in]) to 14.3 mm (0.57 in
[5/16 in]) below the bo

Page 264 of 4378

Load next 8 pages

Page: < prev 1-10 ... 225-232 233-240 241-248 249-256 257-264 265-272 273-280 281-288 289-296 ... 4384 next >

headlamp spare tire technical data remote start ESP headlights