2003 FORD MUSTANG Workshop Manual

trunk tire size heating low beam isofix relay

Page 2321 of 4378

FORD MUSTANG 2003 Workshop Manual DIAGNOSIS AND TESTING
Output State Control (OSC) Mode
Output State Control (OSC) allows the technician to take control of certain parameters to function the
transmission. For example, OSC allows th

DIAGNOSIS AND TESTING
Output State Control (OSC) Mode
Output State Control (OSC) allows the technician to take control of certain parameters to function the
transmission. For example, OSC allows the technician to shift the transmission only when he/she
commands a gear change. If the technician commands 1st gear in OSC, the transmission will remain
in 1st gear until the technician commands the next gear. Another example, the technician can
command a shift solenoid to turn on or off when carrying out an electrical circuit check. OSC has two
modes of operation for transmission, the BENCH MODE and the DRIVE MODE. Each
mode/parameter has a unique set of vehicle operating requirements that the technician is required to
meet before being allowed to operate OSC.
NOTE:
To operate OSC the digital transmission range (TR) sensor must be operational. No Diagnostic
Trouble Codes (DTCs) related to the digital TR sensor can be present.
To operate OSC the vehicle speed source must be operational. No diagnostic codes (DTCs) related to
this source can be present. The vehicle speed source can vary depending on vehicle configuration.
Technicians should verify which input source is applicable for their vehicle application. The following
are potential vehicle speed sources:
„anti- lock braking system (ABS)
„ output shaft speed (OSS) sensor
„ vehicle speed sensor
z The vehicle requirements MUST BE MET when SENDING the OSC value. Refer to individual
test modes for vehicle requirements.
z If the vehicle requirements are NOT MET when SENDING the OSC value, an ERROR
MESSAGE will appear. When the ERROR MESSAGE is received, OSC is aborted and must be
restarted.
z If AFTER SENDING an OSC value, and the vehicle requirements are no longer met, the PCM
will cancel the OSC value and NO ERROR message will appear. Once the vehicle requirements
are met again, the PCM will automatically SEND the previous OSC value without any additional
actions required by the service technician.
z The OSC value XXX may be sent anytime to cancel OSC.
Output State Control (OSC) Procedures
zCarry out visual inspection and vehicle preparation as required.
z Select "Vehicle and Engine Selection" menu.
z Select appropriate vehicle and engine.
z Select "Diagnostic Data Link."
z Select "Powertrain Control Module."
z Select "Output Test Mode."
z Select "KOEO On- Demand Self Test and KOER On- Demand Self Tests."
z Carry out test and record DTCs.
z Repair all NON- Transmission DTCs.
z Repair all digital TR Sensor DTCs.
SECTION 307-
01: Automatic Transaxle/Transmission 2003 Mustang Workshop Manual Klj . 1 ba
92003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

Page 2322 of 4378

FORD MUSTANG 2003 Workshop Manual �z
Repair all vehicle speed DTCs.
�z Make sure that the vehicle speed sensor and digital TR sensors are functional.
�z Select "Active Command Modes."
�z Select "Trans - Bench Mode or Trans - Drive

Page 2323 of 4378

FORD MUSTANG 2003 Workshop Manual �z
Select "XXX" to cancel at any time.
�z Press "SEND."
EPC in BENCH MODE
The BENCH MODE is also used to test the functionality of the transmissions electronic pressure
control. During BENCH MODE

Page 2324 of 4378

FORD MUSTANG 2003 Workshop Manual �z
75 - sets EPC pressure to 517 kPa (75 psi).
�z 90 - sets EPC pressure to 620 kPa (90 psi).
�z XXX - cancels OSC value sent.
�z SEND - sends the values to PCM.
BENCH MODE Procedure for EPC
Foll

Page 2325 of 4378

FORD MUSTANG 2003 Workshop Manual �z
the engine is ON.
�z the TCC is OFF.
�z the transmission range selector lever is in O/D.
�z the vehicle speed is greater than 3.2 km/h (2 mph).
OSC Command Values
�z1 - PCM selects 1st gear.

Page 2326 of 4378

FORD MUSTANG 2003 Workshop Manual �z
the engine is ON.
�z the transmission range selector lever is in O/D.
�z the vehicle speed is greater than 3.2 km/h (2 mph).
OSC "TCC ON" DRIVE MODE operates ONLY when:
�zthe digital TR sensor

Page 2327 of 4378

FORD MUSTANG 2003 Workshop Manual pressures. The best test for the EPC is to use the BENCH MODE and a hydraulic pressure gauge.
Using EPC in the BENCH MODE will confirm that the EPC is working at both the higher and lower
pressures.

Page 2328 of 4378

FORD MUSTANG 2003 Workshop Manual �z
Monitor all selected PIDs during test.
�z Select "Parameters - EPC."
�z Select Value "0- 620 kPa (0-90 psi)."
�z Press "SEND" to send command.
�z Re- Select Value "0- 620 kPa (0-90 psi)."
�z P

Load next 8 pages

Page: < prev 1-10 ... 2289-2296 2297-2304 2305-2312 2313-2320 2321-2328 2329-2336 2337-2344 2345-2352 2353-2360 ... 4384 next >

belt instrument cluster tire pressure reset headlight aiming tire pressure fuel type