2003 FORD MUSTANG Workshop Manual

wheel ignition rear view mirror wheel bolt torque fuel fill door release hood release

Page 4025 of 4378

FORD MUSTANG 2003 Workshop Manual 2. Turn the ignition switch to the RUN position.
3. Follow manufacturers instructions for the scan tool being used.
4. PIDs are continuously updated on the display.
Active Commands
This command a

2. Turn the ignition switch to the RUN position.
3. Follow manufacturer's instructions for the scan tool being used.
4. PIDs are continuously updated on the display.
Active Commands
This command allows the technician to verify operation of the air bag indicator and chime. When the
air bag output command is executed, the indicator and the chime are activated simultaneously for
approximately four seconds. Both devices are deactivated automatically.
Restraints Control Module (RCM) Diagnostic Trouble Code (DTC) Priority Table DTC
a LFC
b LFC
Priority Description Action To
Take — — 1 The Air Bag Indicator is Illuminated Continuously —
RCM
Disconnected, Inoperative, or Lost/Low Ignition Feed Go To Pinpoint
Test A .
B1342 24 2 RCM Is Faulted INSTALL a
new RCM.
B1231 19 3 RCM Crash Data Memory Full INSTALL a
new RCM.
B1921 21 4 RCM Bracket Ground Resistance High Go To Pinpoint
Test B .
C1414 29 5 Incorrect Vehicle Identification Code Go To Pinpoint
Test C .
B1887 15 6 Driver Air Bag Circuit Shorted to Ground Go To Pinpoint
Test D .
B1916 15 7 Driver Air Bag Circuit Shorted to Battery or Ignition Go To Pinpoint
Test E .
B1888 16 8 Passenger Air Bag Circuit Shorted to Ground Go To Pinpoint
Test F .
B1925 16 9 Passenger Air Bag Circuit Shorted to Battery or Ignition Go To Pinpoint
Test G .
B1932 32 10 Driver Air Bag Circuit Resistance High Go To Pinpoint
Test H .
B1933 33 11 Passenger Air Bag Circuit Resistance High Go To Pinpoint
Test I .
B1934 34 12 Driver Air Bag Circuit Resistance Low Go To Pinpoint
Test J .
B1935 35 13 Passenger Air Bag Circuit Resistance Low Go To Pinpoint
Test K .
B1892 — 17 Air Bag Tone Warning Indicator Circuit Shorted to
Ground or Open Go To Pinpoint
Test L .
B1891 — 18 Air Bag Tone Warning Indicator Circuit Shorted to Battery
or Ignition Go To Pinpoint
Test M .
B1869 Tone
c 19 Air Bag Indicator Inoperative Go To Pinpoint
Test N .
B1870 Tone
c 20 Air Bag Indicator Shorted to Battery Go To Pinpoint
Test O . Klj . 3 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

Page 4026 of 4378

FORD MUSTANG 2003 Workshop Manual a
DTC: Diagnostic Trouble Code, retrieved using a scan tool.
b LFC: Lamp fault code, flashed on air bag indicator.
c Tone will sound only if additional DTCs are present.
Inspection and Verificat

Page 4027 of 4378

FORD MUSTANG 2003 Workshop Manual restraints control module
�zData Link Connector
(DLC).
�z RCM.
�z Circuitry. Test P . Klj . 5 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108

Page 4028 of 4378

FORD MUSTANG 2003 Workshop Manual DIAGNOSIS AND TESTING
Pinpoint Tests —
Air Bag Supplemental Restraint System
(SRS)
Restraint System Diagnostic Tool Warning
WARNING: This tool is for restraint system service only. Remove from

Page 4029 of 4378

FORD MUSTANG 2003 Workshop Manual An air bag indicator that is illuminated continuously can be caused by one of the following:
�zworn or damaged shorting bar or camming beam.
�z the ignition circuit damaged.
�z the RCM disconnected

An air bag indicator that is illuminated continuously can be caused by one of the following:
zworn or damaged shorting bar or camming beam.
z the ignition circuit damaged.
z the RCM disconnected from the vehicle harness.
z a loss of RCM ground circuits.
z the RCM inoperative.
z circuitry.
PINPOINT TEST A: THE AIR BAG WARNING INDICATOR IS
ILLUMINATED CONTINUOUSLY — RCM DISCONNECTED,
INOPERATIVE, OR LOST/LOW IGNITION FEED Test Step Result / Action to
Take A1 CHECK FOR CONTINUOUS OR ON-
DEMAND SELF TEST DTCs z
Key in OFF position.
z Connect the diagnostic tool. Scan Tool
z Key in ON position.
z Enter the following diagnostic mode on the diagnostic tool:
Retrieve/Clear Continuous DTCs.
z Retrieve and record any continuous DTCs for use later in this pinpoint
test.
z Enter the following diagnostic mode on the diagnostic tool: On-
Demand Self Test.
z Were any continuous or on- demand self test DTCs retrieved? Yes
If continuous
DTCs were
retrieved, GO to
A3
. If on-
demand
DTCs were
retrieved, GO to
the Restraints
Control Module
(RCM) Diagnostic
Trouble Code
(DTC) Priority
Table in this
section for
pinpoint test
direction.
No
GO to A2 .
A2 CHECK THE RCM CONNECTION
WARNING: If the supplemental restraint system (SRS) is
being serviced, the system must be deactivated and restraint
system diagnostic tools must be installed. Refer to Air Bag Supplemental Restraint System (SRS) in this section.
The air bag restraint system diagnostic tools must be removed
and the air bag modules reconnected when the system is
reactivated to avoid non- deployment in a collision, resulting in
possible personal injury. NOTE: Diagnostics or repairs are not to
be performed on a seat equipped with a seat side air bag with the
seat in the vehicle. Prior to attempting to diagnose or repair a seat
concern when equipped with a seat side air bag, the seat must be
removed from the vehicle and the restraint system diagnostic tools
must be installed in the seat side air bag electrical connectors. The
restraint system diagnostic tools must be removed prior to
operating the vehicle over the road. NOTE: After diagnosing or Yes
GO to
A3 .
No
CONNECT C2041
and engage the
locking tabs. GO
to A7 . Klj . 2 ba
462003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

Page 4030 of 4378

FORD MUSTANG 2003 Workshop Manual repairing an SRS,
the restraint system diagnostic tools must be
removed before operating the vehicle over the road. NOTE: After
diagnosing or repairing a seat system, the restraint system
diagno

Page 4031 of 4378

FORD MUSTANG 2003 Workshop Manual �z
Is the voltage between 9 and 16 volts? A5 CHECK THE GROUND CIRCUIT 397 (BK/WH) FOR AN OPEN
�z
Key in OFF position.
�z Measure the resistance between RCM C2041 pin 21, circuit 397
(BK/WH), harne

Page 4032 of 4378

FORD MUSTANG 2003 Workshop Manual Pinpoint Test B: LFC 21/DTC B1921 —
RCM Bracket Ground Resistance High
Normal Operation
WARNING: The tightening torque of the restraints control module (RCM) retaining bolts is
critical for prop

Pinpoint Test B: LFC 21/DTC B1921 —
RCM Bracket Ground Resistance High
Normal Operation
WARNING: The tightening torque of the restraints control module (RCM) retaining bolts is
critical for proper air bag supplemental restraint system (SRS) operation. Refer to Restraints Control Module (RCM) in this section for correct torque values.
The restraints control module (RCM) monitors the resistance between the ground connections at its
housing and the reference ground at pin 21. If the RCM detects a resistance greater than 100 ohms, it
will store a diagnostic trouble code (DTC) B1921 in memory and flash a lamp fault code (LFC) 21 (or
higher priority code if one exists) on the air bag indicator.
Possible Causes
High resistance between the RCM housing ground and pin ground can be caused by:
zincorrect seating of the RCM retaining bolts.
z incorrect tightening torque of the RCM retaining bolts.
z high resistance on RCM logic ground circuit 397 (BK/WH).
PINPOINT TEST B: LFC 21/DTC B1921 — RCM BRACKET GROUND
RESISTANCE HIGH section for
pinpoint test
direction.
No
RECONNECT the
system.
REACTIVATE the
system. PROVE
OUT the system.
REFER to
Air Bag Supplemental
Restraint System
(SRS) in this
section. CLEAR all
DTCs. Test Step Result / Action to Take
B1 CHECK FOR A HARD OR INTERMITTENT DTC
z
Key in OFF position.
z Connect the diagnostic tool. Scan Tool
z Key in ON position.
z Enter the following diagnostic mode on the diagnostic tool:
Retrieve/Clear Continuous DTCs.
z Retrieve and record any continuous DTCs for use later in
this pinpoint test.
z Enter the following diagnostic mode on the diagnostic tool:
On- Demand Self Test.
z Was DTC B1921 retrieved during the on- demand self Yes
This is a hard fault. The fault
condition is still present. This
fault cannot be cleared until it
is corrected and the DTC is
no longer retrieved during the
on-demand self test. GO to
B2 .
No Klj . 5 ba
462003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

Load next 8 pages

Page: < prev 1-10 ... 3993-4000 4001-4008 4009-4016 4017-4024 4025-4032 4033-4040 4041-4048 4049-4056 4057-4064 ... 4384 next >

instrument cluster jump start adblue heater roof rack mirror