2003 FORD MUSTANG Workshop Manual

washer fluid airbag stop start tire pressure radio antenna clutch

Page 81 of 4378

FORD MUSTANG 2003 Workshop Manual REFILL as necessary.
�z Power steering pump
brackets loose or
misaligned. �z
CHECK bolts, brackets
and bracket alignment.
TIGHTEN bolts to
specification. REPAIR
or INSTALL new
brackets as nec

Page 82 of 4378

FORD MUSTANG 2003 Workshop Manual surfaces
�zYoke spring in the
steering gear. �z
CHECK TSBs for
revised yoke spring for
applicable vehicles.
�z Accessory drive
belt squeal/chirp—
when rotating the
steering wheel
from stop

surfaces
zYoke spring in the
steering gear. z
CHECK TSBs for
revised yoke spring for
applicable vehicles.
z Accessory drive
belt squeal/chirp—
when rotating the
steering wheel
from stop to stop z
Loose or worn
accessory drive belt. z
ADJUST or INSTALL a
new accessory belt as
necessary. REFER to
Section 303 - 05 .
z Power steering
gear hiss z
Steering column
intermediate/flexible
shaft- to-steering gear
is binding or
misaligned. z
REPAIR or INSTALL a
new
intermediate/flexible
shaft as necessary.
REFER to Section 211 -
04 .
z Grounded or loose
steering column boot at
the dash panel. z
REPAIR as necessary.
z Damaged or worn
steering gear input
shaft and valve. z
REPAIR or INSTALL a
new steering gear as
necessary. REFER to
Section 211 - 02 .
z Steering column
rattle z
Loose bolts or
attaching brackets. z
TIGHTEN the bolts to
specifications.
z Loose, worn or
insufficiently lubricated
column bearings. z
LUBRICATE or
INSTALL new steering
column bearings as
necessary. REFER to
Section 211 - 04 .
z Steering shaft
insulators damaged or
worn. z
INSTALL new
insulators. REFER to
Section 211 - 04 .
z Intermediate/flexible
shaft compressed or
extended. z
INSPECT the rubber
spider coupling for
damage. INSTALL a
new
intermediate/flexible
shaft. REFER to Section 211 - 04 .
z Steering column
squeak or cracks z
Insufficient lubricated
steering shaft
bushings. z
LUBRICATE the
steering shaft and shaft
tube seals.
z Loose or misaligned
steering column
shrouds. z
TIGHTEN or ALIGN the
steering column
shrouds.
z Steering wheel rubbing
against steering
column shrouds. z
REPOSITION the
steering column
shrouds.
z Insufficient lubricated
speed control slip ring. z
LUBRICATE the speed
control slip ring.
z Upper or lower bearing
sleeve out of position. z
REPOSITION the
bearing sleeves.
z Power steering
pump noisy z
Incorrect assembly of
components.
z Imperfections on the
outside diameter or z
REPAIR or INSTALL a
new power steering
pump as necessary.
REFER to Section 211 -Klj . 35 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Page 83 of 4378

FORD MUSTANG 2003 Workshop Manual end surface of the
power steering pump
rotor.
�z Damaged or worn
power steering pump
rotor splines.
�z A crack on the inner
surface of the power
steering pump cam.
�z Interference between
th

Page 84 of 4378

FORD MUSTANG 2003 Workshop Manual �z
Clunk— noise from the
front suspension, occurs
in and out of turns �z
Loose front
struts or shocks. �z
INSPECT for loose nuts
or bolts. TIGHTEN to
specifications. REFER to
Section 204 - 0

Page 85 of 4378

FORD MUSTANG 2003 Workshop Manual acceleration from a slow
speed or stop
assembly
mispositioned. and the rear suspension
for damage or wear.
REPAIR as necessary.
�z Incorrect or high
CV joint
operating angle. �z
CHECK vehicle

acceleration from a slow
speed or stop
assembly
mispositioned. and the rear suspension
for damage or wear.
REPAIR as necessary.
z Incorrect or high
CV joint
operating angle. z
CHECK vehicle ride
height is within limits.
REPAIR as necessary.
z Damaged or
worn front
suspension
components. z
CHECK for a loose
stabilizer bar, damaged
or loose strut/strut
bushings or loose or
worn ball joints.
INSPECT the steering
linkage for wear or
damage. REPAIR or
INSTALL new
components as
necessary.
z Shimmy—most
noticeable on
coast/deceleration. Also
hard steering condition z
Excessive
positive caster. z
CHECK the caster
alignment angle.
CORRECT as
necessary. REFER to
Section 204 - 00 .
Symptom Chart—
Tire Noise/Vibration Condition
Possible Sources Action
z Tire noise— hum/moan
at constant speeds z
Abnormal wear
patterns. z
SPIN the tire and CHECK
for tire wear. INSTALL a
new tire as necessary.
INSPECT for
damaged/worn suspension
components. CARRY OUT
wheel alignment.
z Tire noise— noise tone
lowers as the vehicle
speed is lowered z
Out-of- balance
tire. z
BALANCE the tire and
road test. INSTALL a new
tire as necessary. REFER
to Section 204 - 04 .
z Tire noise — ticking
noise, changes with
speed z
Nail puncture or
stone in tire
tread. z
INSPECT the tire. REPAIR
as necessary.
z Wheel and tire—
vibration and noise
concern is directly
related to vehicle
speed and is not
affected by
acceleration, coasting
or decelerating z
Damaged or
worn tire. z
Go To Pinpoint Test J .
z Tire wobble or
shudder — occurs at
lower speeds z
Damaged wheel
bearings. z
SPIN the tire and CHECK
for abnormal wheel
bearing play or roughness.
ADJUST or INSTALL new
wheel bearings as
necessary. REFER to
Section 204 - 01 .
z Damaged wheel. zINSPECT the wheel for
damage. INSTALL a new
wheel as necessary.
REFER to Section 204 -Klj . 38 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Page 86 of 4378

FORD MUSTANG 2003 Workshop Manual 01 .
�z Damaged or
worn suspension
components. �z
INSPECT the suspension
components for wear or
damage. REPAIR as
necessary.
�z Loose wheel
nuts. �z
CHECK the wheel nuts.
TIGHTEN to specif

Page 87 of 4378

FORD MUSTANG 2003 Workshop Manual Symptom Chart—
Transmission (Manual) and Transfer Case Noise/Vibration Condition
Possible Sources Action
�z Clutch rattling noise—
occurs with clutch
engaged, noise
changes/disappears
with

Symptom Chart—
Transmission (Manual) and Transfer Case Noise/Vibration Condition
Possible Sources Action
z Clutch rattling noise—
occurs with clutch
engaged, noise
changes/disappears
with clutch pedal
depressed z
Flywheel bolts,
clutch housing bolts
or clutch pressure
plate bolts loose. z
TIGHTEN the bolts to
specifications. CHECK
the bolts for damage.
z Clutch squeaking
noise— noise is heard
when the clutch is
operated. Vehicle
moves slowly or
creeps when the clutch
is disengaged. Can
also be difficult to shift
into first and reverse
gear z
Pilot bearing seized
or damaged. z
INSTALL a new pilot
bearing. REFER to
Section 308 - 01 .
z Clutch squeaking
noise— occurs with
clutch pedal
depressed/released z
Worn clutch pedal
shaft or bushings. z
INSPECT the clutch
pedal for wear or
damage. REPAIR as
necessary. REFER to
Section 308 - 02 .
z Clutch whirring/rattle
noise— occurs when
clutch pedal is
depressed z
Worn, damaged or
misaligned clutch
release bearing. z
INSTALL a new clutch
release bearing.
REFER to Section 308 -
01 .
z Clutch grating/grinding
noise— occurs when
clutch pedal is
depressed z
Clutch pressure
plate fingers bent or
worn. z
INSPECT the clutch
pressure plate release
fingers. INSTALL a new
pressure plate as
necessary. REFER to
Section 308 - 01 .
z Contact surface of
clutch release
bearing worn or
damaged. z
INSTALL a new clutch
release bearing.
REFER to Section 308 -
01 .
z Clutch chatter— a
small amount of noise
when clutch pedal is
released at initial take-
off z
Clutch engagement. zAcceptable operating
condition.
z Clutch chatter/grabs—
in some cases a
shudder is felt. Occurs
with clutch pedal
depressed/released z
Damaged or worn
powertrain/driveline
mounts. z
INSPECT the
powertrain/drivetrain
mounts. INSTALL new
mounts as necessary.
REFER to Section 303 -
01A for 3.8L engines or
Section 303 - 01B for
4.6L (2V) engines.
z Binding or dragging
plunger of the clutch
master cylinder or
slave cylinder. z
CHECK the master and
slave cylinder
operation. INSPECT
the components for
damage or wear.
INSTALL a new master
or slave cylinder as
necessary. REFER to Klj . 40 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Page 88 of 4378

FORD MUSTANG 2003 Workshop Manual Section 308 - 02 .
�z Grease or oil on the
clutch disc facing. �z
CHECK the input shaft
seal and rear main oil
seal. REPAIR as
necessary. INSTALL a
new clutch disc.
REFER to Section 308 -
03

Load next 8 pages

Page: < prev 1-10 ... 49-56 57-64 65-72 73-80 81-88 89-96 97-104 105-112 113-120 ... 4384 next >

ECO mode driver seat adjustment coolant radio hood open service indicator