Page 4001 of 4378
4. Install the quarter trim panel (31012) and the angel wing trim. For additional information, refer to
Section 501 - 05 .
5. Make sure the shoulder belt passes through the belt holder on the top of the seatback.
6. Check the active restraint system for correct operation. Klj . 3 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...
Page 4002 of 4378
REMOVAL AND INSTALLATION
Retractor —
Rear Seat Safety Belt, Convertible
Removal 1. Remove the rear seat cushion.
2. Remove the luggage compartment front lining board (45444).
3. Release the safety belt guide.
4. Using the special tool, remove the safety belt anchor bolt.
5. Using the special tool, remove the bolt and the rear safety belt retractor.
SECTION 501-
20A: Safety Belt System 2003 Mustang Workshop Manual Special Tool(s)
Torx Bit, Safety Belt Bolt
501-
010 (T77L-2100- A) Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...
Page 4003 of 4378
Installation
NOTE:
Make sure the safety belt is not twisted when inserting it in the quarter trim panel.
1. Using the special tool, install the bolt and the rear safety belt retractor.
2. Using the special tool, install the safety belt anchor bolt.
3. Install the safety belt guide.
4. Install the luggage compartment front lining board. Klj . 2 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...
Page 4004 of 4378
5. Install the rear seat cushion.
6. Make sure the shoulder belt passes through the belt holder on the top of the seatback.
7. Check the active restraint system for correct operation. Klj . 3 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...
Page 4005 of 4378
REMOVAL AND INSTALLATION
Child Safety Seat Belt —
Tether Anchor
Removal and Installation
Hard top only 1. Remove the package tray. For additional information, refer to Section 501 - 05 .
2. Remove the bolts and the tether anchor bracket.
Convertible only 3. NOTE: Rework the sheet metal to its original condition and structural integrity.
The convertible model tether anchors are part of the sheet metal. zThese are accessed through the trunk by removing the trunk front trim.
Hard top only 4. NOTE: Rework the sheet metal to its original condition and structural integrity.
To install, reverse the removal procedure.
Hard top and convertible 5. Check the restraint system for correct operation.
SECTION 501-
20A: Safety Belt System 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...
Page 4006 of 4378
Klj . 2 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...
Page 4007 of 4378
REMOVAL AND INSTALLATION
Safety Belt Buckle —
Front Seat
Removal
Driver and passenger seat 1. Remove the front seat. For additional information, refer to Section 501 - 10 .
2. Remove the nut and the safety belt buckle.
Driver seat only 3. Disconnect the safety belt buckle electrical connector.
Installation 1. To install, reverse the removal procedure.
SECTION 501-
20A: Safety Belt System 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...
Page 4008 of 4378
2. Check the restraint system for correct operation. Klj . 2 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...