2003 FORD MUSTANG Workshop Manual

fuel consumption climate control open hood service interval reset wiper size winter tyres

Load previous 8 pages

Page 2361 of 4378

FORD MUSTANG 2003 Workshop Manual D2 SOLENOID FUNCTIONAL TEST
�z
Install 2,060 kPa (300 psi) pressure gauge into EPC tap.
�z Monitor pressure gauge.
�z Enter the following diagnostic mode on the diagnostic tool:
Parameter; EPC.
�

Page 2362 of 4378

FORD MUSTANG 2003 Workshop Manual XXX.
�z Press "SEND".
�z Does the voltage and solenoid state change? D5 CHECK LEAD FRAME CONNECTIONS
�z
Key in OFF position.
�z Disconnect: Lead Frame.
�z Inspect for damaged or pushed out pins,

Page 2363 of 4378

FORD MUSTANG 2003 Workshop Manual PINPOINT TEST E: OUTPUT SHAFT SPEED (OSS) SENSORS
Test Step Result / Action to Take
NOTE:
Refer to the Output Shaft Speed (OSS) Sensor Harness Connector illustration preceding
these pinpoint test

PINPOINT TEST E: OUTPUT SHAFT SPEED (OSS) SENSORS
Test Step Result / Action to Take
NOTE:
Refer to the Output Shaft Speed (OSS) Sensor Harness Connector illustration preceding
these pinpoint tests. E1 ELECTRONIC DIAGNOSTICS
z
Check to make sure the transmission harness
connector is fully seated, pins are fully engaged in
connector and in good condition before proceeding.
z Connect the diagnostic tool.
z Key in ON position.
z Enter the following diagnostic mode on the diagnostic
tool: Diagnostic Data Link.
z Enter the following diagnostic mode on the diagnostic
tool: PCM.
z Select PID/Data Monitor and Record.
z Select the PID OSS.
z Does vehicle enter PID/Data Monitor and Record? Yes
GO to
E2 .
No
REPEAT procedure to ENTER
PID. If vehicle did not enter PID,
REFER to the Powertrain
Control/Emissions Diagnosis
(PC/ED) manual for diagnosis of
PCM. E2 DRIVE CYCLE TEST
z
While monitoring the OSS Speed PID, drive the
vehicle so that the transmission upshifts and
downshifts through all gears.
z Does the OSS Speed PID increase and decrease
with engine and vehicle speed? Yes
CLEAR all DTCs. ROAD TEST to
verify if concern is still present. If
concern is still present, REFER to
Diagnosis By Symptom
in this
section.
No
If the OSS Speed PID does not
increase and decrease with
engine and vehicle speed,
INSPECT for open or short in
vehicle harness, sensor, a PCM
concern, or internal hardware
concern.
If the sensor signal is erratic,
INSPECT for intermittent concern
in the internal/external harness,
sensor, or connector.
If the sensor signal is steady, GO
to E3 .
E3 CHECK RESISTANCE OF OSS SENSOR
z
Disconnect the vehicle harness connector from the
OSS sensor.
z Measure the resistance between the OSS sensor pins. Yes
REFER to
Diagnosis By Symptom for concern diagnosis.
No
INSTALL a new OSS sensor. Klj . 20 ba
222003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

Page 2364 of 4378

FORD MUSTANG 2003 Workshop Manual PINPOINT TEST F: SOLENOID MECHANICAL FAILURE �z
Record the resistance.
�z Is the resistance within specification? Sensor Resistance (ohms) Temperature
OSS 791 to 1,795 -
40°C to 160°C
(-40�

Page 2365 of 4378

FORD MUSTANG 2003 Workshop Manual Klj . 22 ba
222003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

Page 2366 of 4378

FORD MUSTANG 2003 Workshop Manual DIAGNOSIS AND TESTING
Special Testing Procedures
The special tests are designed to aid the technician in diagnosing the hydraulic and mechanical portion
of the transmission.
Engine Idle Speed Chec

Page 2367 of 4378

FORD MUSTANG 2003 Workshop Manual 2. Start engine and check line pressures. Refer to the Line Pressure Chart to determine if line
pressure is within specification.
a EPC readings will vary due to EEC strategy. These values are appr

2. Start engine and check line pressures. Refer to the Line Pressure Chart to determine if line
pressure is within specification.
a EPC readings will vary due to EEC strategy. These values are approximate pressures. Actual clutch
apply pressures should be within 69- 103 kPa (10-15 psi) of line pressure. For additional information on
testing, refer to the Clutch Pressure Test in this section. Line Pressure Chart Application Range Idle WOT Stall
EPC Line Pressure EPC Line Pressure
4.6L P, N, OD,
2, 1 207-
276 kPa
(30- 40 psi) 552-
689 kPa (80-
100 psi) 689-
758 kPa
(100- 110 psi) 1310-1448 kPa
(190- 210 psi) 4.6L R 13-
82 kPa (2-
12 psi) 441-
683 kPa (64-
99 psi) 572-
655 kPa
(83- 95 psi) 1427-
1855 kPa
(207- 269 psi) 3.8L P, N, OD,
2, 1 138-
207 kPa
(20- 30 psi) 448-
586 kPa (65-
85 psi) 689-
758 kPa
(100- 110 psi) 1310-1448 kPa
(190- 210 psi) 3.8L R 103-
172 kPa
(15- 25 psi) 448-
620 kPa (65-
90 psi) 572-
662 kPa
(83- 96 psi) 1427-
1862 kPa
(207- 270 psi)
Clutch Pressure Chart 3.8L Transmission Pressures with TP at 1.5 Volts and Vehicle Speed Above 8 Km/h (5 MPH)
Gear EPC Tap
a Line Pressure
Tap Forward Clutch
Tap Intermediate
Clutch Tap Direct Clutch
Tap M1 172-
241 kPa
(25-35 psi) 517-
655 kPa (75-
95 psi) 448-
586 kPa (65-
85 psi) 0-
34 kPa (0-5 psi) 0-
34 kPa (0-5
psi) M2 103-
241 kPa
(15-25 psi) 413-
551 kPa (60-
80 psi) 344-
482 kPa (50-
70 psi) 393-
517 kPa (55- 75
psi) 0-
34 kPa (0-5
psi) 1 172-
241 kPa
(25-35 psi) 517-
655 kPa (75-
95 psi) 448-
586 kPa (65-
85 psi) 0-
34 kPa (0-5 psi) 0-
34 kPa (0-5
psi) 2 103-
241 kPa
(15-25 psi) 413-
551 kPa (60-
80 psi) 358-
468 kPa (52-
68 psi) 379-
517 kPa (55- 75
psi) 0-
34 kPa (0-5
psi) 3 137-
206 kPa
(20-30 psi) 413-
517 kPa (60-
75 psi) 413-
517 kPa (60-
75 psi) 413-
551 kPa (60- 80
psi) 379-
517 kPa
(55- 75 psi) 4 172-
241 kPa
(25-35 psi) 517-
655 kPa (75-
95 psi) 0-
34 kPa (0- 5
psi) 482-
620 kPa (70- 90
psi) 448-
586 kPa
(65- 85 psi)
Clutch Pressure Chart 4.6L Transmission Pressures with TP at 1.5 Volts and Vehicle Speed Above 8 Km/h (5 MPH)
Gear EPC Tap
a Line Pressure
Tap Forward Clutch
Tap Intermediate
Clutch Tap Direct Clutch
Tap M1 172-
241 kPa
(25-35 psi) 517-
655 kPa (75-
95 psi) 448-
586 kPa (65-
85 psi) 0-
34 kPa (0-5 psi) 0-
34 kPa (0- 5
psi) M2 103-
241 kPa
(15-25 psi) 413-
551 kPa (60-
80 psi) 344-
482 kPa (50-
70 psi) 393-
517 kPa (55- 75
psi) 0-
34 kPa (0- 5
psi) 1 172-
241 kPa 517-
655 kPa (75- 448-
586 kPa (65- 0-
34 kPa (0-5 psi) 0-
34 kPa (0- 5 Klj . 2 ba
72003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

Page 2368 of 4378

FORD MUSTANG 2003 Workshop Manual a
EPC readings will vary due to EEC strategy. These values are approximate pressures. Actual clutch
apply pressures should be within 69- 103 kPa (10-15 psi) of line pressure. For additional informat

a
EPC readings will vary due to EEC strategy. These values are approximate pressures. Actual clutch
apply pressures should be within 69- 103 kPa (10-15 psi) of line pressure. For additional information on
testing, refer to the Clutch Pressure Test in this section.
3. Place the ignition switch in the OFF position. If line pressure is not within specification, check EPC pressure.
4. Connect pressure gauge to EPC pressure tap.
5. Start engine and check EPC pressure. Use the line pressure chart for specifications.
6. If EPC pressure is not within specification, Go To Pinpoint Test E to diagnose EPC operation. If
EPC operation is OK, see the line pressure diagnosis chart for line pressure concern causes. (25-
35 psi) 95 psi) 85 psi) psi)
2 103-
241 kPa
(15-25 psi) 413-
544 kPa (60-
79 psi) 344-
482 kPa (50-
70 psi) 379-
517 kPa (55- 75
psi) 0-
34 kPa (0- 5
psi) 3 172-
241 kPa
(25-35 psi) 517-
655 kPa (75-
95 psi) 372-
579 kPa (54-
84 psi) 482-
613 kPa (70- 89
psi) 379-
586 kPa
(55-85 psi) 4 241-
310 kPa
(35-45 psi) 620-
758 kPa (90-
110 psi) 0-
34 kPa (0-5
psi) 586-
730 kPa (85-
105 psi) 551-689 kPa
(80-100 psi)
Line Pressure Diagnosis Chart Test Results Possible Source
High At Idle —
In All
Positions ·
Wiring Harnesses ·
Run Quick Test. Refer to the Powertrain Control/Emissions Diagnosis
(PC/ED) manual. ·
EPC Solenoid ·
Main Regulator Valve Low At Idle —
In All
Positions ·
Low Fluid Level ·
Control Bodies ·
Leakage in Pump ·
Damaged Gaskets on Separator Valve ·
Damaged Separator Plate ·
Restricted Inlet Filter ·
Case Bolts ·
Loose Main Control Valve Body ·
EPC Solenoid O- Ring ·
EPC Solenoid Bracket ·
Case ·
Sticking Main Regulator Valve ·
Damaged Inlet Tube Seal on Inlet Filter Low In Park Only ·
Valve Body ·
Low/Reverse Servo Low In Reverse Only ·
Separator Plate ·
Low/Reverse Servo or Valve Bodies Klj . 3 ba
72003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

Load next 8 pages

Page: < prev 1-10 ... 2329-2336 2337-2344 2345-2352 2353-2360 2361-2368 2369-2376 2377-2384 2385-2392 2393-2400 ... 4384 next >

engine overheat service interval reset coolant temperature TPMS apple carplay check transmission fluid