PINPOINT TEST B: ALL DOOR LOCKS ARE INOPERATIVE z
Measure the reistance between the GEM C201b pin 4, circuit
397 (BK/WH), harness side and ground.
z Is the reistance less than 5 ohms? GO to
A3 .
No
REPAIR the circuit(s) in
question. TEST the system
for normal operation. A3 CHECK CIRCUIT 397 (BK/WH) FOR SHORT TO POWER
z
Measure the voltage between the GEM C201b pin 4, circuit
397 (BK/WH), harness side and ground.
z Is any voltage present? Yes
REPAIR the circuit. TEST
the system for normal
operation.
No
REFER to
Section 418 - 00 .
Test Step Result / Action to
Take B1 CHECK POWER LOCK INPUTS TO THE GEM
z
Connect the diagnostic tool.
z Monitor the GEM PIDS DR_LOCK, DR_UNLK, PD_LOCK,
PD_UNLK, while depressing the driver and passenger power door
lock and unlock switches.
z Do the PID values agree with the switch positions? Yes
GO to
B11 .
No
GO to B2 .
B2 ISOLATE BETWEEN THE DRIVER AND PASSENGER POWER
DOOR LOCK SWITCHES NOTE:
This PID may not be supported in the normal scan tool PID
list. It can be located in the Function test —"Transmitter Tic/Data".
When this test is activated, the appropriate results may be obtained
when pressing the keyfob buttons.
z Connect the diagnostic tool.
z Monitor the GEM PIDS DR_LOCK and DR_UNLK, while
depressing the driver power door lock and unlock switches.
z Do the PID values agree with the switch positions? Yes
GO to
B7 .
No
GO to B3 .
B3 CHECK CIRCUIT 326 (WH/VT) FOR VOLTAGE —
DRIVER SIDE z
Disconnect: Master Window/Door Lock Control Switch C508.
z Measure the voltage between master window/door lock control
switch C508 Pin 3, Circuit 326 (WH/VT), harness side and ground. Yes
GO to
B4 .
No Klj . 7 ba
212003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...
PINPOINT TEST D: THE LUGGAGE COMPARTMENT DOOR IS
INOPERATIVE USING THE REMOTE TRANSMITTER the normal scan tool PID list. It can be
located in the Function Test —
"
Transmitter Tic/DATA". When this test is
activated, the appropriate results may be
obtained when pressing the keyfob
buttons.
z Remove the ignition key from the ignition.
z Connect the diagnostic tool.
z Monitor the GEM FUNCTION TEST
TIC/DATA while pressing the lock and
unlock buttons on the remote transmitter.
z Does LAST DATA RECEIVED match
the button presses of the remote
transmitter? INSTALL a new GEM. For additional
information, REFER to
Section 419 - 10 .
REPEAT the self- test. CLEAR the DTCs.
No
GO to C4 .
C4 CHECK THE BATTERIES IN THE
REMOTE TRANSMITTER z
Install new batteries in the remote
transmitter.
z Connect the diagnostic tool.
z Monitor the GEM FUNCTION TEST
TIC/DATA while pressing the lock and
unlock buttons on the remote transmitter.
z Does LAST DATA RECEIVED match
the button presses of the remote
transmitter? Yes
SYSTEM is OK. REPEAT the self-test.
CLEAR the DTCs.
No
GO to
C5 .
C5 REPROGRAM THE REMOTE
TRANSMITTERS TO THE GEM z
NOTE: When carrying out the following
procedure it must be noted that all
previous programmed remote transmitters
will be erased. The customer needs to be
informed that any remote transmitters not
present during the programming mode will
not operate the vehicle. All remote
transmitters must be programmed at the
same time.
z Reprogram the remote transmitter to the
GEM. For additional information, refer to
Programming — Keyless Entry Remote
Transmitter .
z Connect the diagnostic tool.
z Monitor the GEM FUNCTION TEST
TIC/DATA while pressing the lock and
unlock buttons on the remote transmitter.
z Does LAST DATA RECEIVED match
the button presses of the remote
transmitter? Yes
SYSTEM is OK. REPEAT the self-test.
CLEAR the DTCs.
No
PROGRAM a new remote transmitter to the
vehicle. For additional information, REFER to
Programming
— Keyless Entry Remote
Transmitter . REPEAT the self-
test. CLEAR
the DTCs. If the problem still remains,
INSTALL a new GEM and program the remote
transmitters to the vehicle. For additional
information, REFER to Section 419 - 10 .
REPEAT the self- test. CLEAR the DTCs. Test Step Result / Action to Take
D1 CHECK IGNITION STATES
z
Connect the diagnostic tool.
z Monitor the GEM PIDS IGN_KEY, IGN_A, IGN_S, and
IGN_R while cycling the ignition switch through the OFF,
ACC, RUN, START and key out positions. Yes
GO to
D2 .
No Klj . 14 ba
212003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...
