2003 FORD MUSTANG hood release

relay wheel bolt torque rear entertainment change wheel immobilizer turn signal bulb

Page 1493 of 4378

FORD MUSTANG 2003 Workshop Manual REMOVAL
Engine
Removal
1. Remove the battery. For additional information, refer to Section 414 - 01 .
2. Release the fuel pressure. For additional information, refer to Section 310 - 00 .
3.

Page 1851 of 4378

FORD MUSTANG 2003 Workshop Manual pressure reading. Release pressure and repeat the test. Install a new radiator cap if the
pressure is not 99.3-
121.4 kPa (14.4-17.6 psi).
Cap — 4.6L
WARNING: Never remove the pressure relief ca

pressure reading. Release pressure and repeat the test. Install a new radiator cap if the
pressure is not 99.3-
121.4 kPa (14.4-17.6 psi).
Cap — 4.6L
WARNING: Never remove the pressure relief cap while the engine is operating or when the
cooling system is hot. Failure to follow these instructions can result in damage to the cooling
system or engine or personal injury. To avoid having scalding hot coolant or steam blow out of
the degas bottle when removing the pressure relief cap, wait until the engine is cooled, then
wrap a thick cloth around the pressure relief cap and turn it slowly. Step back while the
pressure is released from the cooling system. When you are sure all the pressure has been
released, turn and remove the pressure relief cap (still with a cloth).
1. Remove the pressure relief cap from the degas bottle.
2. Follow the instructions from the pressure tester.
3. NOTE: If the plunger of the pump is depressed too quickly, an erroneous pressure reading will
result.
Slowly depress the plunger of the pressure test pump until the pressure gauge reading stops
increasing and note the highest pressure reading obtained.
4. If the pressure test gauge readings are not within specifications, install a new pressure relief cap. If the pressure test gauge readings are within specifications, carry out the cooling system
Pressure Test.
Thermostat — Water
A new water thermostat should be installed only after the following electrical and mechanical tests
have been carried out.
Thermostat — Electrical Test
CAUTION: Always vent the exhaust to the outside when carrying out this test.
NOTE: The electrical thermostat test is most accurate if carried out at less than 37.8°C (100°F)
ambient air. This test may be carried out with or without the hood open and with the engine warm or
cold.
1. Check the engine coolant level. Fill as needed.
2. With the ignition OFF, remove the engine coolant temperature (ECT) (4.6L) or cylinder head temperature (CHT) (3.8L) sensor harness connector and attach ECT (4.6L) or CHT (3.8L)
Sensor "T" Cable as a jumper between the powertrain control module (PCM) (12A650) and the
ECT (4.6L) or CHT (3.8L) sensor. Attach the 73III Automotive Meter to the ECT (4.6L) or CHT
(3.8L) Sensor "T" Cable. Voltage values (0- 5 V) may now be monitored while the sensor retains
its connection to the wiring harness.
An appropriate diagnostic tool may be used to monitor the ECT on vehicles equipped with data link connector (DLC). Klj . 8 ba
102003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Page 2683 of 4378

FORD MUSTANG 2003 Workshop Manual 4. Remove the front seat. For additional information, refer to
Section 501 - 10 .
5. Unhook the clutch release lever cable (7K553) from the clutch pedal adjuster quadrant (7L583).
6. Open the hood

Page 4086 of 4378

FORD MUSTANG 2003 Workshop Manual NOTE:
If a seat equipped with a seat mounted side air bag and/or a safety belt pretensioner (if
equipped) system is being serviced, the air bag system must be deactivated.
NOTE: Restraint system

NOTE:
If a seat equipped with a seat mounted side air bag and/or a safety belt pretensioner (if
equipped) system is being serviced, the air bag system must be deactivated.
NOTE: Restraint system diagnostic tools MUST be installed under the seats in the seat side air bag (if
equipped) and safety belt pretensioner (if equipped) to floor connectors.
NOTE: Diagnostics or repairs are not to be performed on a seat equipped with a seat side air bag with
the seat in the vehicle. Prior to attempting to diagnose or repair a seat concern when equipped with a
seat side air bag, the seat must be removed from the vehicle and the restraint system diagnostic tools
must be installed in the seat side air bag electrical connectors. The restraint system diagnostic
tools must be removed prior to operating the vehicle over the road.
NOTE: After diagnosing or repairing an SRS, the restraint system diagnostic tools must be
removed before operating the vehicle over the road.
NOTE: After diagnosing or repairing a seat system, the restraint system diagnostic tools must be
removed before operating the vehicle over the road.
NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the
customer.
1. WARNING: To avoid accidental deployment and possible personal injury, the
backup power supply must be depleted before repairing or replacing any front or side air
bag supplemental restraint system (SRS) components and before servicing, replacing,
adjusting or striking components near the front or side air bag sensors, such as doors,
instrument panel, console, door latches, strikers, seats and hood latches.
Please refer to the appropriate vehicle shop manual to determine location of the front air
bag sensors.
The side air bag sensors are located at or near the base of the B- pillar.
To deplete the backup power supply energy, disconnect the battery ground cable and
wait at least one minute. Be sure to disconnect auxiliary batteries and power supplies (if
equipped).
Disconnect the battery ground cable and wait at least one minute. For additional information,
refer to Section 414 - 01 .
2. Remove the steering column opening lower finish panel. 1. Remove the screws.
2. Pull out to release the retaining clips and remove the steering column opening lower finish panel.
3. Remove the steering column opening lower reinforcement. 1. Remove the bolts.
2. Remove the steering column opening lower reinforcement. Klj . 2 ba
72003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

check engine light technical specifications load capacity brake fluid 4WD alternator