Page 3305 of 3870
2. Turn the ignition switch to the "ON" position.
3. Diagnose the CAN bus line.
4. Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the CAN bus line found to be normal?
YES: Go to Step 3.
NO: Repair the CAN bus line (Refer to DIAGNOSTIC TROUBLE
CODE DIAGNOSIS
or DIAGNOSIS < VEHICLES WITHOUT
ADVANCED AIR BAG
). Then go to Step 2.
STEP 2. Recheck for diagnostic trouble code.
1. Turn the ignition switch to the "ON" position.
2. Erase the DTC.
3. Turn the ignition switch to the "LOCK" (OFF) position.
4. Turn the ignition switch to the "ON" position.
5. Check if the DTC is set. CAUTION: To prevent damage to scan tool MB991958,
always turn the ignition switch to the
"LOCK" (OFF) position before connecting or
disconnecting scan tool MB991958.
2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor
Page 3306 of 3870
Fig. 127: Rechecking For Diagnostic Trouble Code
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor
Page 3307 of 3870
6. Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC C1345 set?
YES: Go to Step 3.
NO: The procedure is complete.
STEP 3. Check the brake warning light.
Check that the brake warning light illuminates with the parking brake lever
pulled up.
Q: Does the brake warning light illuminate?
YES: Replace the hydraulic unit (integrated with TCL/ASC-ECU). Then
go to Step 12.
NO: Go to Step 4.
STEP 4. Check the brake fluid amount.
Q: Is the brake fluid within lower and upper limits of the reservoir?
YES: Go to Step 5.
NO: Check the basic brake system to determine why the brake fluid was
decreased.
STEP 5. Check the brake warning light.
1. Disconnect brake fluid level switch connector A-04 and parking brake
switch connector
C-34.
2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor
Page 3308 of 3870
Fig. 128: Disconnecting Brake Fluid Level Switch Connector A
-04
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor
Page 3309 of 3870
Fig. 129: Disconnecting Parking Brake Switch Connector C
-34
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2. Turn the ignition switch to the "ON" position.
Q: Does the brake warning light illuminate?
YES: Go to Step 6.
NO: Check the brake fluid level switch (Refer to BRAKE FLUID
LEVEL SENSOR CHECK
, ) and parking brake switch and replace
them if necessary. Then go to Step 12.
STEP 6. Measure the resistance at combination meter connector C-102.
1. Disconnect brake fluid level switch connector A-04 and parking brake
switch connector
C-34.
2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor
Page 3310 of 3870
Fig. 130: Disconnecting Brake Fluid Level Switch Connector A
-04
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor
Page 3311 of 3870
Fig. 131: Disconnecting Parking Brake Switch Connector C
-34
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2. Disconnect the connector C-102
2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor
Page 3312 of 3870
2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor