Page 265 of 3870
Fig. 160: Identifying Front ABS Sensor/Rear ABS Sensor
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
INSPECTION ABS SENSOR CHECK
2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor
Page 266 of 3870
1. Check whether any metallic foreign material has adhered to the projection at
the speed sensor tip. Remove any foreign material. Also check whether the
pole piece is damaged. Replace it with a new one if it is damaged.
2. Measure the resistance between the ABS sensor terminals.
Standard value: 1.24 - 1.64 kohm
Fig. 161: Measuring Resistance Between ABS Sensor Terminals
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
3. If the internal resistance of the ABS sensor is no
t within the standard value, NOTE: The projection can become magnetized due to the
magnet inside the ABS sensor, causing foreign material
to easily adhere to it. The projection may not be able to
correctly sense the wheel rotation speed if foreign
matter is on it or if it is damaged.
2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor
Page 267 of 3870
replace it with a new ABS sensor.
4. Remove all connections from the ABS sensor. The circuit should be open
between terminals (1) and (2) and the body of the ABS sensor. If the circuit is
not open, replace with a new ABS sensor.
Fig. 162: Opening Terminals (1) And (2)
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
5. Check the ABS sensor cable for breaka
ge, dama
ge or disconnection. Re
place
2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor
Page 268 of 3870
with a new one if a problem is found.
TOOTHED ABS ROTOR CHECK Check whether the ABS rotor teeth are broken or deformed. Replace the BJ
assembly of the drive shaft, or the rear hub assembly, respectively, if the teeth are
damaged or deformed.
Fig. 163: Locating Tooth ABS Rotor
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
G-SENSOR REMOVAL AND INSTALLATION NOTE: When checking for cable damage, remove the cable clamp
part from the body and then gently bend and pull the cable
near the clamp.
CAUTION: Do not drop or apply a shock on the G-sensor.
2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor
Page 269 of 3870
Fig. 164: Removing & Installing G
-Sensor
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
INSTALLATION SERVICE POINT >>A<< G-SENSOR INSTALLATION The arrow mark on the G-sensor must point toward the rear of the vehicle. INSPECTION G-SENSOR CHECK Required Special Tool:
MB991348: Test Harness Set
1. Disconnect the G-sensor connector and connect special tool MB991348, between the disconnected connectors.
2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor
Page 270 of 3870
Fig. 165: Disconnecting G
-Sensor Connector And Connectin
g Special Tool
MB991348
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor
Page 271 of 3870
2. With the ignition switch turned to the "ON" position, read the voltage between
terminals number 2 and number 3.
Standard Value: 2.4 - 2.6 V
3. With special tool MB991348 connected, rotate so that the arrow points straight
down. Read output voltage between terminals number 2 and number 3.
Standard Value: 3.4 - 3.6 V
4. If the voltage deviates from the standard value, check the power supply wire
and ground wire. If no problems are found, replace the G-sensor. SPECIFICATIONS FASTENER TIGHTENING SPECIFICATION FASTENER TIGHTENING SPECIFICATION GENERAL SPECIFICATIONS Fig. 166: General Specifications
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
SERVICE SPECIFICATION ITEM
SPECIFICATION
Brake tube flare nut
15 +/- 2 N.m (12 +/- 1 ft-lb)
2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor
Page 272 of 3870
Fig. 167: Service Specificatio
n
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor