Page 905 of 3870
Fig. 60: Checking Stoplight Switch Connector C
-03, C
-04
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 906 of 3870
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA
.
Q: Are the connector and terminals in good condition?
YES : Go to Step 10.
NO : Repair or replace the damaged components. Then go to Step 22 .
STEP 10. Check the harness wire between stoplight switch connector C-03
terminal 1 and joint connector (1) C-04 terminal 11 for damage.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 907 of 3870
Fig. 61: Checkin
g Harness Wire
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 908 of 3870
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA
.
Q: Is the harness wire in good condition?
YES : Go to Step 11.
NO : Repair the damaged harness wire. Then go to Step 22 .
STEP 11. Check the stoplight switch.
1. Remove the stoplight switch. (Refer to BRAKE PEDAL
).
2. Connect an ohmmeter to the stoplight switch between terminals 1 and 2.
Fig. 62: Connecting Ohmmeter To Stoplight Switch
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
3. Check for continuity between the terminals when the plunger of the
sto
plight switch is
pushed in, and check for an o
pen circuit when it is
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 909 of 3870
released.
Fig. 63: Checking Continuity
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
4. The stoplight switch is operating properly if there is continuity between
terminals 1 and 2 when the plunger is pushed in to a depth of within 4.5
mm (0.2 inch) from the outer case edge surface, and if the circuit is open
between terminals 1 and 2 when it is released.
Q: Is the circuit between terminals 1 and 2 still closed even with the
plunger pushed in or open when it is released?
YES : It can be assumed that this malfunction is intermittent, (Refer to
HOW TO COPE WITH INTERMITTENT MALFUNCTIONS
), and
install the stoplight switch. (Refer to BRAKE PEDAL
). Then go to Step
22 .
NO : Replace the stoplight switch. (Refer to BRAKE PEDAL
). Then go
to Step 2
2 .
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 910 of 3870
STEP 12. Check stoplight switch connector C-03 for loose, corroded or
damaged terminals, or terminals, or terminals pushed back in the
connector.
Fig. 64: Checking Stoplight Switch Connector C
-03
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Are the connector and terminals in good condition?
YES : Go to Step 13.
NO : Repair or replace the damaged components. Then go to Step 22 .
STEP 13. Check the harness wire between stoplight switch connector C-03
terminal 2 and relay box for damage.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 911 of 3870
Fig. 65: Checking Harness Wire
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Is the harness wire in good condition?
YES : Go to Step 14.
NO : Repair the damaged harness wire. Then go to Step 22 .
STEP 14. Check the fuse number 11 at the relay box in engine
compartment.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 912 of 3870
Fig. 66: Checking Fuse Number 11
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Is the fuse in good condition?
YES : It can be assumed that this malfunction is intermittent. (Refer to
HOW TO COPE WITH INTERMITTENT MALFUNCTIONS
).
Then go to Step 22 .
NO : Replace the fuse. Then go to Step 22 .
STEP 15. Measure the terminal voltage at PCM connector B-19.
1. Disconnect all the connectors from the PCM.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor