2007 NISSAN TIIDA Service Repair Manual

keyless entry spark plugs replace spare tire location height adjustment wiring diagram tire size

Page 5305 of 5883

NISSAN TIIDA 2007 Service Repair Manual VEHICLE SPEED SENSOR MTR
TM-359
< COMPONENT DIAGNOSIS >[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
VEHICLE SPEED SENSOR MTR
DescriptionINFOID:0000000001712989
The vehicle speed sensor·MTR

VEHICLE SPEED SENSOR MTR
TM-359
< COMPONENT DIAGNOSIS >[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
VEHICLE SPEED SENSOR MTR
DescriptionINFOID:0000000001712989
The vehicle speed sensor·MTR is built into the speedometer assembly. The sensor functions as an auxiliary
device to the revolution sensor when it is malfunctioning. The TCM will then use a signal sent from the vehicle
speed sensor·MTR.
CONSULT-III Reference Value in Data Monitor ModeINFOID:0000000001712990
Remarks: Specification data are reference values.
On Board Diagnosis LogicINFOID:0000000001712991
Diagnostic trouble code “VHCL SPEED SEN-MTR” with CONSULT-III or 2nd judgement flicker without CON-
SULT-III is detected when TCM does not receive the proper voltage signal from the sensor.
Possible CauseINFOID:0000000001712992
Harness or connector
(Sensor circuit is open or shorted.)
Vehicle speed sensor
DTC Confirmation ProcedureINFOID:0000000001712993
CAUTION:
Always drive vehicle at a safe speed.
If performing this “DTC Confirmation Procedure” again, always turn ignition switch OFF and wait at
least 10 seconds before continuing.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-III
1. Turn ignition switch ON and select “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
2. Touch “START”.
3. Start engine and accelerate vehicle from 0 to 25 km/h (0 to 16 MPH).
4. If the check result is NG, go to TM-359, "
Diagnosis Procedure".
WITHOUT CONSULT-III
1. Start engine.
2. Drive vehicle under the following conditions:
Selector lever position: “D” position
Vehicle speed: Higher than 25 km/h (16 MPH)
3. Perform self-diagnosis. Refer to TM-38, "
Diagnosis Procedure without CONSULT-III".
4. If the check result is NG, go to TM-359, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000001712995
1.CHECK INPUT SIGNAL
With CONSULT-III
1. Start engine.
2. Select “TCM INPUT SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
3. Read out the value of “VHCL/S SE-MTR” while driving.
Check the value changes according to driving speed.
Item name Condition Display value
VHCL/S SE-MTR During driving Approximately matches the speedometer reading.
Item name Condition Display value
VHCL/S SE-MTR During drivingApproximately matches
the speedometer reading.

Page 5306 of 5883

NISSAN TIIDA 2007 Service Repair Manual TM-360
< COMPONENT DIAGNOSIS >[TYPE 2 (4AT: RE4F03B)]
VEHICLE SPEED SENSOR MTR
Without CONSULT-III
1. Start engine.
2. Check voltage between TCM connector terminal and ground.
OK or NG
OK >> GO TO 3.

Page 5307 of 5883

NISSAN TIIDA 2007 Service Repair Manual SHIFT SOLENOID VALVE A
TM-361
< COMPONENT DIAGNOSIS >[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
SHIFT SOLENOID VALVE A
DescriptionINFOID:0000000001713002
Shift solenoid valves A and B are

SHIFT SOLENOID VALVE A
TM-361
< COMPONENT DIAGNOSIS >[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
SHIFT SOLENOID VALVE A
DescriptionINFOID:0000000001713002
Shift solenoid valves A and B are turned ON or OFF by the TCM in response to signals sent from the PNP
switch, vehicle speed and ECM (throttle opening). Gears will then be shifted to the optimum position.
CONSULT-III Reference Value in Data Monitor ModeINFOID:0000000001713003
Remarks: Specification data are reference values.
On Board Diagnosis LogicINFOID:0000000001713004
Diagnostic trouble code “SHIFT SOLENOID/V A” with CONSULT-III or 4th judgement flicker without CON-
SULT-III is detected when TCM detects an improper voltage drop when it tries to operate the solenoid valve.
Possible CauseINFOID:0000000001713005
Harness or connector
(Solenoid circuit is open or shorted.)
Shift solenoid valve A
DTC Confirmation ProcedureINFOID:0000000001713006
CAUTION:
Always drive vehicle at a safe speed.
If performing this “DTC Confirmation Procedure” again, always turn ignition switch OFF and wait at
least 10 seconds before continuing.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-III
1. Turn ignition switch ON and select “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
2. Touch “START”.
3. Start engine.
4. Drive vehicle in “D” position and allow the transaxle to shift 1 → 2 (“GEAR”).
5. If the check result is NG, go to TM-361, "
Diagnosis Procedure".
WITHOUT CONSULT-III
1. Start engine.
2. Drive vehicle in D
1→ D2 position.
3. Perform self-diagnosis. Refer to TM-38, "
Diagnosis Procedure without CONSULT-III".
4. If the check result is NG, go to TM-361, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000001713008
1.CHECK INPUT SIGNAL
With CONSULT-III
1. Start engine.
2. Select “MAIN SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
3. Read out the value of “SHIFT S/V A” while driving.
Check the value changes according to driving speed.
Gear position 1 2 3 4
Shift solenoid valve A ON (Closed) OFF (Open) OFF (Open) ON (Closed)
Shift solenoid valve B ON (Closed) ON (Closed) OFF (Open) OFF (Open)
Item name Condition Display value
SHIFT S/V AWhen shift solenoid valve A operates.
(When driving in “D
1” or “D4”.)ON
When shift solenoid valve A does not operate.
(When driving in “D
2” or “D3”.)OFF

Page 5308 of 5883

NISSAN TIIDA 2007 Service Repair Manual TM-362
< COMPONENT DIAGNOSIS >[TYPE 2 (4AT: RE4F03B)]
SHIFT SOLENOID VALVE A
Without CONSULT-III
1. Start engine.
2. Check voltage between TCM connector terminal and ground.
OK or NG
OK >> GO TO 5.
NG

Page 5309 of 5883

NISSAN TIIDA 2007 Service Repair Manual SHIFT SOLENOID VALVE A
TM-363
< COMPONENT DIAGNOSIS >[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
OK >> GO TO 4.
NG >> Repair open circuit or short to ground or short to power in harness or

Page 5310 of 5883

NISSAN TIIDA 2007 Service Repair Manual TM-364
< COMPONENT DIAGNOSIS >[TYPE 2 (4AT: RE4F03B)]
SHIFT SOLENOID VALVE A
Check solenoid valve by listening for its operating sound while
applying battery voltage to the terminal and ground.
SCIA

Page 5311 of 5883

NISSAN TIIDA 2007 Service Repair Manual SHIFT SOLENOID VALVE B
TM-365
< COMPONENT DIAGNOSIS >[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
SHIFT SOLENOID VALVE B
DescriptionINFOID:0000000001713010
Shift solenoid valves A and B are

SHIFT SOLENOID VALVE B
TM-365
< COMPONENT DIAGNOSIS >[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
SHIFT SOLENOID VALVE B
DescriptionINFOID:0000000001713010
Shift solenoid valves A and B are turned ON or OFF by the TCM in response to signals sent from the PNP
switch, vehicle speed and ECM (throttle opening). Gears will then be shifted to the optimum position.
CONSULT-III Reference Value in Data Monitor ModeINFOID:0000000001713011
Remarks: Specification data are reference values.
On Board Diagnosis LogicINFOID:0000000001713012
Diagnostic trouble code “SHIFT SOLENOID/V B” with CONSULT-III or 5th judgement flicker without CON-
SULT-III is detected when TCM detects an improper voltage drop when it tries to operate the solenoid valve.
Possible CauseINFOID:0000000001713013
Harness or connector
(Solenoid circuit is open or shorted.)
Shift solenoid valve B
DTC Confirmation ProcedureINFOID:0000000001713014
CAUTION:
Always drive vehicle at a safe speed.
If performing this “DTC Confirmation Procedure” again, always turn ignition switch OFF and wait at
least 10 seconds before continuing.
WITH CONSULT-III
1. Turn ignition switch ON and select “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
2. Touch “START”.
3. Start engine.
4. Drive vehicle in “D” position and allow the transaxle to shift 1 → 2 → 3 (“GEAR”).
5. If the check result is NG, go to TM-365, "
Diagnosis Procedure".
WITHOUT CONSULT-III
1. Start engine.
2. Drive vehicle in D
1→ D2→ D3 position.
3. Perform self-diagnosis.
Refer to TM-38, "
Diagnosis Procedure without CONSULT-III".
4. If the check result is NG, go to TM-365, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000001713016
1.CHECK INPUT SIGNAL
With CONSULT-III
1. Start engine.
2. Select “MAIN SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
3. Read out the value of “SHIFT S/V B” while driving.
Check the value changes according to driving speed.
Gear position 1 2 3 4
Shift solenoid valve A ON (Closed) OFF (Open) OFF (Open) ON (Closed)
Shift solenoid valve B ON (Closed) ON (Closed) OFF (Open) OFF (Open)
Item name Condition Display value
SHIFT S/V BWhen shift solenoid valve B operates.
(When driving in “D
1” or “D2”.)ON
When shift solenoid valve B does not operate.
(When driving in “D
3” or “D4”.)OFF

Page 5312 of 5883

NISSAN TIIDA 2007 Service Repair Manual TM-366
< COMPONENT DIAGNOSIS >[TYPE 2 (4AT: RE4F03B)]
SHIFT SOLENOID VALVE B
Without CONSULT-III
1. Start engine.
2. Check voltage between TCM connector terminal and ground.
OK or NG
OK >> GO TO 5.
NG

Load next 8 pages

Page: < prev 1-10 ... 5273-5280 5281-5288 5289-5296 5297-5304 5305-5312 5313-5320 5321-5328 5329-5336 5337-5344 ... 5888 next >

steering wheel brake pads replacement radio antenna engine homelink fuel pressure