Page 2905 of 5883
EM-258
< PREPARATION >[K9K]
PREPARATION
PREPARATION
PREPARATION
Special Service ToolsINFOID:0000000001381459
NISSAN tool number
(RENAULT tool No.)
Tool nameDescription
EM03470000
(—)
Piston ring compressorInstalling piston assembly into cylinder bore
K V 1 0 1111 0 0
(—)
Seal cutterRemoving oil pan
KV10112100
(—)
Angle wrenchTightening bolts for bearing cap, cylinder
head, etc. in angle
KV113B0020
(Emb. 880)
Sliding hammerInertia extractor
KV113B0060
(Mot. 582-01)
Ring gear stopperFlywheel immobilizing tool.
KV113B0110
(Mot. 1430)
TDC set pinSet of TDC pins
NT044
NT046
NT014
MBIB0358E
MBIB0363E
Page 2906 of 5883
PREPARATION
EM-259
< PREPARATION >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
KV113B0120
(Mot. 1485-01)
Oil jet removerTool for removing the piston bottom oil jets
KV113B0130
(Mot. 1489)
TDC set pinTDC setting pin
KV113B0140
(Mot. 1492)
Bearing assembling setTool for installing connecting rod bearing
KV113B0150
(Mot. 1492-03)
Bearing assembling adapterAdaptation kit for installing the detachable cap
connecting rod bearing
KV113B0160
(Mot. 1493-01)
Bearing insertTool for installing main bearing
KV113B0170
(Mot. 1494)
Oil jet remover plateTool for removing oil jets
KV113B0190
(Mot. 1567)
Clip pliersPliers for exhaust gas recycling pipe clips
KV113B0210
(Mot. 1585)
Front oil seal driftTool for installing crankshaft seals, flywheel
end NISSAN tool number
(RENAULT tool No.)
Tool nameDescription
MBIB0372E
MBIB0373E
MBIB0374E
MBIB0375E
MBIB0376E
MBIB0381E
Page 2907 of 5883
EM-260
< PREPARATION >[K9K]
PREPARATION
Commercial Service Tools
INFOID:0000000001381460
KV113B0220
(Mot. 1586)
Front oil seal drift setTool for installing crankshaft seals, timing end
KV113B0230
(Mot. 1632)
Camshaft seal insertTool for installing inlet camshaft seals
KV113B0240
(Rou. 15-01)
Shaft protectorInternal shaft protector
16 mm (0.63 in) dia.
KV113B0400
(Mot. 1592)
Compression gauge attachmentConnecting compression gauge and glow
plug holex
—
(Mot. 1606-A)
Camshaft pulley holderTool for locking sprockets for toothed timing
belt
—
(Mot. 1638)
Belt tension gaugeSetting drive belt tension NISSAN tool number
(RENAULT tool No.)
Tool nameDescription
MBIB0712E
E1BIA0053ZZ
MBIB0382E
NISSAN tool number
(RENAULT tool No.)
Tool nameDescription
KV113B0030
(Mot. 11)
Crankshaft bearing removerCrankshaft bearing extractor
KV113B0040
(Mot. 251-01)
Dial gauge stand setGauge stand used with KV113B0050 (Mot.
252-01)
MBIB0359E
MBIB0360E
Page 2908 of 5883
PREPARATION
EM-261
< PREPARATION >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
KV113B0050
(Mot. 252-01)
Dial gauge stand setThrust plate for measuring the protrusion of
cylinder liners used with KV113B0040 (Mot.
251-01).
KV113B0090
(Mot. 1335)
Valve seal removerTool for removing valve stem seals
KV113B0180
(Mot. 1511-01)
Valve seal driftTool for installing valve stem seals
KV113B0200
(Mot. 1573)
Cylinder head standCylinder head support
KV113E0010
(Mot. 1566)
Fuel spill tube spannerSpanner for installing and removing injection
tubes
WS39930000
(—)
Tube presserPressing the tube of liquid gasket
Manual lift table caddy Removing and installing engine NISSAN tool number
(RENAULT tool No.)
Tool nameDescription
MBIB0361E
MBIB0370E
MBIB0378E
MBIB0380E
MBIB0379E
NT052
ZZA1210D
Page 2909 of 5883
EM-262
< PREPARATION >[K9K]
PREPARATION
Piston ring expander Removing and installing piston ring
(Mot. 588)Liner retaining strap
(664000)
Cylinder head test containerTool for testing the cylinder head, including: a
tray and the various kits suited for each model
of cylinder head (plug, sealing plate, blanking
plate).
Torx socketStandard 1/2" (12.7 mm) square drive 8/12 /14
female torx socket.
(Mot. 1505)
(Mot. 1715)
Frequency meterTool for belt tension checking with frequency
Glow plug wrench Articulated wrench for removing and installing
the glow plugs
Main bearing wrench Wrench for removing main bearings NISSAN tool number
(RENAULT tool No.)
Tool nameDescription
NT030
MBIB0364E
MBIB0383E
MBIB1423E
MBIB0387E
MBIB0388E
Page 2910 of 5883
![NISSAN TIIDA 2007 Service Repair Manual DRIVE BELTS
EM-263
< ON-VEHICLE MAINTENANCE >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
ON-VEHICLE MAINTENANCE
DRIVE BELTS
Exploded ViewINFOID:0000000001381461
Inspection and AdjustmentINFOID:0000000001381 NISSAN TIIDA 2007 Service Repair Manual DRIVE BELTS
EM-263
< ON-VEHICLE MAINTENANCE >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
ON-VEHICLE MAINTENANCE
DRIVE BELTS
Exploded ViewINFOID:0000000001381461
Inspection and AdjustmentINFOID:0000000001381](/manual-img/5/57395/w960_57395-2909.png)
DRIVE BELTS
EM-263
< ON-VEHICLE MAINTENANCE >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
ON-VEHICLE MAINTENANCE
DRIVE BELTS
Exploded ViewINFOID:0000000001381461
Inspection and AdjustmentINFOID:0000000001381462
INSPECTION
WARNING:
Be sure to perform when the engine is stopped.
1. Inspect drive belt for cracks, fraying, wear and oil. Replace drive belt if necessary.
2. Manually evaluate the drive belt tension (tension cannot be measured using frequency meter).
3. Replace drive belt when tension is beyond normal operating limit.
CAUTION:
Auto-tensioner must be replaced with a new one when the belt is replaced.
ADJUSTMENT
Belt tensioning is not necessary, as it is automatically adjusted by auto-tensioner.
Removal and InstallationINFOID:0000000001381463
CAUTION:
Replace any drive belt that has been removed with a new one.
Auto-tensioner must be replaced with new one when the drive belt is replaced.
Do not run the engine without the drive belt to avoid damaging the crankshaft pulley.
REMOVAL
1. Remove engine undercover using power tool.
2. Remove RH front wheel. Refer to WT-6, "
Rotation".
3. Remove right side splash cover.
E1BIA0021ZZ
1. Crankshaft pulley 2. A/C compressor 3. Drive belt
4. Generator 5. Drive belt auto-tensioner
Page 2911 of 5883
EM-264
< ON-VEHICLE MAINTENANCE >[K9K]
DRIVE BELTS
4. Remove drive belt.
Turn drive belt auto-tensioner adjusting bolt clockwise to
release drive belt tension.
INSTALLATION
1. Install the drive belt.
CAUTION:
Make sure drive belt is correctly engaged with the pulley
groove.
Check for oil and coolant on drive belt and each pulley
groove.
Certain drive belts have five teeth whereas the air condi-
tioning compressor pulley, power-assisted steering pump
pulley, and generator pulley all have six teeth.In this case,
it is essential to check that inner tooth (O) of the pulleys
remains free when fitting the drive belt.
Never turn the engine in the opposite direction to its nor-
mal operating direction.
Use a brush to remove any deposits from the crankshaft
pulley V grooves.
2. Release drive belt auto-tensioner, and apply tension to drive belt.
3. Turn crankshaft pulley clockwise several times to equalize tension between each pulley.
MBIB0353E
MBIB0516E
Page 2912 of 5883
AIR CLEANER FILTER
EM-265
< ON-VEHICLE MAINTENANCE >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
AIR CLEANER FILTER
Removal and InstallationINFOID:0000000001528961
REMOVAL
1. Push the tabs (A) of both ends of the air cleaner cover (1) into
the inside (B).
2. Pull up the air cleaner cover (1) and remove it (C).
3. Remove air cleaner filter (1) and holder (2) assembly from the
air cleaner case.
4. Remove the air cleaner filter (1) from the holder (2).
INSPECTION AFTER REMOVAL
It is necessary to clean air cleaner filter or replace it at the recommended intervals, more often under dusty
conditions. Refer to MA-7, "
Periodic Maintenance".
Blow air into the back side of air cleaner filter until no objects spray
out.
INSTALLATION
Installation is in the reverse order of removal.
Install the air cleaner cover (1) in the direction shown.
PBIC3557J
PBIC3558J
SMA384C
2 : Air cleaner filter
3 : Holder
PBIC3559J