Page 537 of 4264
CAB 10-29
Important Operations
1. Front Console Assembly
Refer to Floor Consol in this section.
2. Glove Box
Remove 2 fixing screws and pulling the handle.
3. Instrument Panel Driver Lower Cover Assembly
1) Remove the engine hood opener 2 fixing screws.
2) Remove the lower cover one fixing screw.
3) Pull out the cover (Stick type parking brake only).
4) Pull out the lower cover assembly.
4. Driver Knee Bolster Assembly
Remove 4 fixing bolts.
Caution:
For precaution on installation or removal of SRS-air bag
system, refer to section 9 “Supplemental Restraint System
(SRS) - AIR BAG”
5. Driver Air Bag
6. Steering Wheel/Steering Cowl
Refer to Section 3B “STEERING COLUMN” for steering
lock assembly removal steps.
7. Meter Cluster Assembly
Pull out the 4 clip positions.
Page 538 of 4264
10-30 CAB
12. Instrument Panel & Cross Beam Assembly
1) Remove the two bolts fixing the steering column to the
cross beam and the two bolts fixing the brake pedal
bracket to the cross beam.
2) Remove the two bolts fixing the parking brake bracket to
the cross beam (Stick type parking brake only).
3) Disconnect the control cables at the blower unit and
heater unit.
Remove the front & side cover from the instrumen
t
panel.
4) Remove the fasteners fixing the instrument panel &
cross beam assembly to the body panel.
5) Disconnect the instrument harness connectors.
Page 539 of 4264
CAB 10-31
13.Ashtray Case
Pull out the ashtray case.
14. Center Cluster Assembly
1) Pull out the cluster at the 6 clip positions.
2) Disconnect the cigarette lighter, accessory socket,
hazard switch and clock connectors.
15. Control Lever Assembly
Remove the 2 fixing screws.
17.Ashtray Bracket
Remove the 3 fixing screws and illumination connector.
Caution:
For precautions on installation or removal of SRS-air bag
system, refer to section 9 "Supplemental Restraint System
(SRS) - AIR BAG".
21. Passenger Air Bag
Remove 2 fixing bolts, 2 fixing nuts and connector.
22. Side Ventilation Grille.
Pull out the grilles and disconnect switch connecto
r
(Driver’s side).
23. Vent Duct Assembly/Defroster Nozzle Assembly
Refer to section 1 “HVAC” for defroster nozzle and
ventilation duct removal steps.
25. Instrument Panel
Remove the clip and 6 fixing bolts.
26. Cross Beam
Page 540 of 4264
10-32 CAB
INSTALLATION
This illustration is based on RHD model
RTW4A0LF001101
Installation Steps
1. Cross beam
2. Instrument panel
3. Instrument harness assembly
4. Vent duct assembly/Defroster nozzle
assembly
5. Side ventilation grille
6. Passenger air bag
7. Glove box cover
8. Passenger lower bracket
9. Meter assembly
10. Ashtray bracket
11. Storage box assembly
12. Control lever assembly
13. Center cluster assembly
14. Ashtray case
15. Instrument panel & Cross beam
assembly
16. Side cover
17. Front cover
18. Front pillar trim cover
19. Dash side trim cover
20. Meter cluster assembly
21. Steering wheel/Steering cowl
22. Driver air bag
23. Driver knee bolster assembly
24. Instrument panel driver lower cover assembly
25. Glove box
26. Front console assembly
Page 541 of 4264
CAB 10-33
Important Operations
15. Instrument Panel & Crass Beam Assembly
1) Tighten the 4 bolts fixing the cross beam and body panel
to the specified torque.
Torque N
m (kgf
m/lb
ft)
19 (1.9/14)
2) A Bolt: Steering Column to Cross Beam
Torque N
m (kgf
m/lb
ft)
20 (2.0/14)
B Bolt: Pedal Bracket to Cross Beam
Torque N
m (kgf
m/lb
ft)
15 (1.5/11)
3) C Bolt: Parking Brake Bracket to Cross Beam
Torque Nm (kgfm/lbft)
15 (1.5/11)
21. Steering Wheel/Steering Cowl
Tighten the steering wheel fixing nut to the specified
truque.
Torque N
m (kgf
m/lb
ft)
35 (3.6/26)
Page 542 of 4264
10-34 CAB
FLOOR CONSOLE
REMOVAL AND INSTALLATION
745R300001
A/T Model
Removal Steps
1. Rear floor console (Bucket seat model
only)
2. Front floor console
3. A/T switch
Installation Steps
3. A/T switch
2. Front floor console
1. Rear floor console (Bucket seat model only)
Page 543 of 4264
CAB 10-35
Important Operations - Removal
1. Rear Floor Console (Bucket Seat Model Only)
1) Open the rear console lid and remove 2 screws.
2) Pull out the front part of rear console at the 2 clip
positions.
2. Front Floor Console
1) Remove the 2 screws.
2) Pull out the rear part of front console at the 2 clip
positions and disconnect the switch connecter.
3) Remove the front console by pull out it rear ward.
Page 544 of 4264
10-36 CAB
REMOVAL AND INSTALLATION
745r300002
M/T Model
Removal Steps
1. Rear floor console (Bucket seat model
only)
2. Shift knob
3. Front floor console
Installation Steps
3. Front floor console
2. Shift knob
1. Rear floor console (Bucket seat model
only)