ELECTRICAL-BODY AND CHASSIS 8A-263
WARNING LIGHT BULB, INDICATOR
LIGHT BULB AND ILLUMINATION LIGHT
BULB
Removal
Turn the bulb socket counterclockwise and pull the bulb out.
Installation
To Install, follow the removal steps in the reverse order.
FUEL TANK UNIT
Removal
Dismount the fuel tank first, then remove the fuel tank unit.
1. Remove the rear inner liner -LH
Remove the clip
2. Remove the filler neck.
Remove the screw
3. Remove the ground with cable.
4. Remove the fuel tank band.
T/M jack unit on the vehicle.
Disconnect fuel line quick connectors.
5. Remove the fuel tank unit from the fuel tank.
8A-264 ELECTRICAL-BODY AND CHASSIS
Installation
Rubber Seal
Be absolutely sure that the fuel tank unit rubber seal is
correctly seated.
Connector
Be absolutely sure that the fuel tank unit connector is securely
connected.
This will prevent a poor contact and an open circuit.
VEHICLE SPEED SENSOR (INSTALLED
ON THE TRANSMISSION)
Removal
1. Disconnect the connector.
2. Remove the vehicle speed sensor body by rotating it.
Installation
To Install, follow the removal steps in the reverse order, noting
the following point.
Tighten the vehicle speed sensor to the specified torque.
Vehicle Speed Sensor Tightening Torque Nm (kgfm/lb.ft)
25 4.9 (2.5 0.5/18 3.6)
ELECTRICAL-BODY AND CHASSIS 8A-269
SPEEDOMETER AND TACHOMETER
Speedometer On-Vehicle Inspection
Check the speedometer accuracy with a speedometer tester.
Carefully follow the tester manufacturer’s instructions.
Manual Transmission
RTW38DSH000201
Auto Transmission
RTW38DSH000101
km/h meter km/h
Permissible Range
Indication
G.EXP EC, SAUDI
ISRAEL, SA
20 17.5 - 22.5 20 – 25
40 37.5 - 42.5 40 – 45
60 57.5 - 62.5 60 – 65
80 77.5 - 82.5 80 – 85
100 97.6 - 103.4 99.8 – 105.6
120 117.6 - 123.4 119.8 – 125.6
140 137.6 - 143.4 139.8 – 145.6
160 157.2 - 163.8 159.4 - 166
Auto Transmission (mPH)
RTW48ASH000201
mPH meter km/h
Permissible Range
Indication
G.EXP UK
20 18.5 - 21.5 20 – 23
40 48.5 - 41.5 40 – 43
60 58.5 - 61.5 60 – 63
80 79.1 - 82.5 80 – 83.4
100 98.9 – 102.7 99.8 – 103.6
Tachometer On-Vehicle Inspection
1. Attach a tune-up tester to the engine.
2. Start the engine.
3. Compare the tachometer reading and the tester reading.
If the tachometer indication is outside the permissible
range, the tachometer must be replaced.
4. Gradually increase and decrease the engine speed.
Note the movement of the tachometer needle.
If the needle movement is sluggish, the tachometer must be
replaced.
8A-270 ELECTRICAL-BODY AND CHASSIS
RTW38DSH000401
6VE1 rpm
Indication Permissible Range
750 690-770
1,000 900-1,060
2,000 1,820-2,070
3,000 2,820-3,120
4,000 3,820-4,180
5,000 4,820-5,180
6,000 5,820-6,180
7,000 6,820-7,180
RTW38DSH000501
4JH1-TC rpm
Indication Permissible Range
750 690-810
2,000 1,875-2,125
3,000 2,850-3,150
4,000 3,820-4,180
5,000 4,820-5,180