2004 ISUZU TF SERIES mirror

ACCESSORIES 9-11


No. Connector face No. Connector face
D-13
Black
Rear speaker -LH H-25
BlackINST
Front door -LH
D-17
Black
Rear speaker -RH H-27
BlackINST

Rear body
D-19
White
Remote mirror switch drive side P-1
SilverBattery (+)
D-21
White
Tweeter -RH P-2
SilverRelay 
Fuse box
D-22
White
Tweeter -LH P-5
SilverBattery (-)
H-6
White
Engine room

INST P-6
SilverBody earth
H-14
White
Rear body

Rear door -LH P-10
SilverEngine ground
H-16
White
Rear body
Rear door -RH R-7
BlackRear speaker -LH
H-18
White
Engine room

INST R-8
BlackRear speaker -RH
H-24
Black
INST

Front door -RH

10-2 CAB
WINDSHIELD
REMOVAL


RTW4A0LF000901

Removal Steps
1. Interior trim panels (Front side)
/Headlining/Instrument panel assembly
2. Wiper arm assembly

3. Room mirror
4. Side moulding
5. Vent cowl cover
6. Windshield stopper
7. Upper moulding

8. Windshield glass
9. Engine hood rear seal

CAB 10-3



Important Operations - Removal
3. Room Mirror
Remove the screw and pull the room mirror to upper side.


8. Windshield Glass
Remove the windshield glass, carefully following the steps
listed below:
1) Use a knife to cut through part of the adhesive caulking
material.
2) Secure one end of a piece of steel piano wire (0.02 inches
in diameter) to a piece of wood that can serve as a handle.
3) Use a pair of needle nose pliers to insert the other end o
f
the piano wire through the adhesive caulking material at the
edge of the windshield glass.
4) Secure the other end of the piano wire to another piece o
f
wood.




5) With the aid of an assistant, carefully move the piano wire
with a sawing motion to cut through the adhesive caulking
material around the entire circumference of the windshield
glass.
6) Lift the windshield from the body.
7) Clean any remaining adhesive caulking material from the
area of the body which holds the windshield.
8) Use a soft rag and unleaded gasoline to wipe off an
y
adhesive remaining on the windshield glass.

10-4 CAB

INSTALLATION


RTW4A0LF001201

Installation Steps


1. Engine hood rear seal
2. Upper moulding

3. Windshield glass
4. Windshield stopper
5. Vent cowl cover
6. Side moulding
7. Room mirror

8. Wiper arm assembly
9. Interior trim panels (Front side)
/Headlining/Instrument panel assembly

10-12 CAB
DISASSEMBLY



This illustration is based on RHD model
RTW4A0LF000701

Disassembly Steps

1. Switch bezel/Window regulator handle

2. Power window switch

3. Bezel

4. Door mirror cover

5. Door trim panel

6. Tweeter (Required Option)

7. Door mirror assembly

8. Outer waste seal

9. Bracket

10. Speaker assembly

11. Waterproof sheet

12. Inside lever

13. Window glass




14. Window regulator/Power window
regulator

15. Glass run

16. Glass run rear channel / Glass ran rear
channel with Door lock control or Anti
theft (EC)

17. Door lock assembly/Door lock assembly
with super lock

18. Outside handle protector (EUROPE)

19. Outside handle

20. Door lock cylinder protector (EUROPE)

21. Door lock cylinder / Door lock cylinder
with door lock switch (EC)
22. Door harness assembly
23. Anti rattler

CAB 10-13


Important Operations
1. Switch Bezel/Window Regulator Handle

Remove the 2 screws and disconnect the connectors.




To remove the regulator handle, remove the clip at the
root of the handle by using wire.




2. Power Window Switch

Remove the 3 screws.


3. Bezel

Remove the screw.



4. Door Mirror Cover

Pull out the upper clip, and then take out the cove
r
upward.



5. Door Trim Panel

Pull out the trim panel at the 8 clip positions (Powe
r
window type).

10-14 CAB



 Remove the 2 screws and pull out the trim panel at the 8
clip positions (Window regulator handle type).
RTW3A0SH000701

6. Tweeter (Required option)

Disconnect the tweeter harness connector and remove
the 3 screws.



7. Door Mirror Assembly

Remove 3 fixing bolts and then remove the connector.
8. Outer Waste Seal



9. Bracket
10. Speaker Assembly

Remove the fixing screw and then remove the
connector.
11. Waterproof Sheet

Take care not to damage the sheet when peeling it off.
12. Inside Lever

Disconnect the door lock cables.

10-16 CAB
REASSEMBLY



This illustration is based on RHD model
RTW4A0LF000801

Reassembly Steps
1. Anti rattler
2. Door harness assembly

3. Door lock cylinder / Door lock cylinder
with door lock switch (EC)

4. Door lock cylinder protector (EUROPE)

5. Outside handle

6. Outside handle protector (EUROPE)
7. Door lock assembly / Door lock
assembly with super lock
8. Glass run rear channel / Glass ran rear channel with Door lock control or Anti
theft (EC)
9. Glass run
10. Window regulator / Power window
regulator



11. Window glass
12. Inside lever
13. Waterproof sheet
14. Speaker assembly
15. Bracket
16. Outer waste seal
17. Door mirror assembly
18. Tweeter (Required option)
19. Door trim panel
20. Door mirror cover
21. Bezel
22. Power window switch

23. Switch bezel / Window regulator handle