Page 409 of 4264
ANTI-LOCK BRAKE SYSTEM 5B-3
Torque Specifications
Electronic Hydraulic Control Unit
This illustration is based
on RHD model
E05R300007
Page 410 of 4264
5B -4 ANTI-LOCK BRAKE SYSTEM
4
2 Front Speed Sensor
E05R300002
Page 411 of 4264
ANTI-LOCK BRAKE SYSTEM 5B-5
Front Speed Sensor (4
4, 4
2 High Ride)
E05R300003
Page 412 of 4264
5B -6 ANTI-LOCK BRAKE SYSTEM
Rear Speed Sensor
E05R300008
Page 413 of 4264
ANTI-LOCK BRAKE SYSTEM 5B-7
Electronic Hydraulic Control Unit
Electronic Hydraulic Control Unit and Associated Parts
RHD model LHD model
350R300001-X
Legend
1.
Flare Nut from master cylinder front
2.
Flare Nut to front right wheel cylinder
3. Flare Nut to front left wheel cylinder
4.
Flare Nut to rear wheel cylinder
5.
Electronic Hydraulic Control Unit (EHCU)
6.
Flare Nut from master cylinder rear
7.
Bolt
8.
Front
Removal
1. Disconnect the harness connector.
2. Loosen five flare nuts and remove brake pipes.
After disconnecting brake pipe, cap or tape the
openings of the brake pipe to prevent the entry o
f
foreign matter.
3. Remove three bracket fixing bolts.
Installation
1. Install EHCU and tighten the bolt to the specified
torque.
Torque : 8 N
m (0.8 kg
m /69 lb in)
2. Tighten the flare nuts to the specified torque.
Torque : 16 N
m (1.6 kg
m /12 lb ft)
3. Connect the harness connector.
Page 414 of 4264
5B -8 ANTI-LOCK BRAKE SYSTEM
Front Wheel Speed Sensor
Front Wheel Speed Sensor and Associated Parts
4
2
350R300005
Page 415 of 4264
ANTI-LOCK BRAKE SYSTEM 5B-9
4
4, 4
2 High Ride
350R300006
Legend
1.
Connector Portion
2.
Front Speed Sensor Assembly
3. Bolt : cable to knuckle
4.
Bolt : sensor to knuckle
5.
Nut: cable to upper link (4
2)
Bolt: cable to upper link (4
4)
Removal
1. Remove speed sensor connector at connector
portion.
2. Remove sensor fixing bolt (4).
3. Remove cable fixing bolts and nut (4
2).
4. Disconnect the arrow mark locks of the cable clips.
5. Remove the speed sensor assembly.
Inspection and Repair
1. Check the speed sensor head for presence of
foreign
materials; remove any dirt, etc.
2. Check the head for damage; replace speed sensor i
f
necessary.
3. Check the speed sensor cable for short or open
circuit, and replace with a new one if necessary.
To check for cable short or open, bend or stretch the
cable while checking for continuity.
Page 416 of 4264
5B -10 ANTI-LOCK BRAKE SYSTEM
Installation
1. Install the speed sensor in the knuckle and take care
not to hit the speed sensor head during installation.
2. Install speed sensor fixing bolt and tighten the fixing
bolt to the specified torque.
Torque: 8 Nm (0.8 kgm /69 lb in)
3. Connect the cable clips at the arrow mark places.
4. Install the cable fixing bolt and nut (4
2) and tighten
the fixing bolt and nut to the specified torque.
Torque :
Bolt
8 N
m (0.8 kg
m /69 lb in)
Nut
20 N
m (2.0 kg
m /14 lb ft)
NOTE: Confirm that the cable is not twisted when
connecting the speed sensor cable.
5. Connect the speed sensor connector.