Page 993 of 4264

ELECTRICAL-BODY AND CHASSIS 8A-335
TROUBLESHOOTING
CIGARETTE LIGHTER
1. Lighter does not pop out after being pushed in. It does not become hot.
Checkpoint Trouble Cause Countermeasure
Reinstall or replace the fuse
No. C-12 (15A)
Poor Fuse No. C-12 (15A,
Fuse box) contact or blown
NG
Replace the lighter
Lighter continuity between
center part and outer area
Open circuit or poor connector
contact
Repair open circuit or
connector contact
Voltage between connector 1
B-21 and the ground at
starter SW. is ACC position
(Should be battery voltage
present)
Open circuit or poor connector
contact
NG NG OK
OK OK
Audio system (System should
receive power)
Repair open circuit or
connector contact
Open circuit or poor connector
contact
NG
Continuity between connector
1
B-22 and the ground
2. Lighter pops out prematurely before becoming hot
Repair or replace the lighter
and/or casingDeformed lighter or casing NGLighter and casing
3. Lighter becomes too hot
Repair or replace the lighter
and/or casingDeformed lighter and casing NGLighter and casing
Page 994 of 4264
8A-336 ELECTRICAL-BODY AND CHASSIS
REMOVAL AND INSTALLATION
AUDIO
Refer to Section 9 “ACCESSORIES” for details.
CIGARETTE LIGHTER
Removal
1. Disconnect the battery ground cable.
2. Remove the center cluster ASM.
3. Remove the lighter
1.
4. Disconnect the connector
2.
5. Loosen the ring nut
3 at the back side.
6. Remove the outer case
4.
7. Remove the lighter holder
5 from the bezel.
Installation
Follow the removal procedure in the reverse order to install the
lighter.
Pay close attention to the important points mentioned in the
following paragraphs.
Connector
Be absolutely sure that the lighter connector is securely
connected.
This will prevent a poor contact and an open circuit.
ACC SOCKET
Removal
1. Disconnect the battery ground cable.
2. Remove the center cluster ASM.
3. Disconnect the connector.
4. Remove the holder nut
1.
5. Remove the ACC Socket
2
Installation
Follow the removal procedure in the reverse order to install the
lighter.
Page 995 of 4264
ELECTRICAL-BODY AND CHASSIS 8A-337
POWER DOOR MIRROR
PARTS LOCATION (RHD)
RTW48AXF020401 & RTW48AXF020501
Page 996 of 4264
8A-338 ELECTRICAL-BODY AND CHASSIS
PARTS LOCATION (LHD)
RTW48AXF020601 & RTW48AXF020701
Page 997 of 4264
ELECTRICAL-BODY AND CHASSIS 8A-339
CIRCUIT DIAGRAM (RHD)
RTW48AXF012401
Page 998 of 4264
8A-340 ELECTRICAL-BODY AND CHASSIS
CIRCUIT DIAGRAM (LHD)
RTW48AXF012201
Page 999 of 4264
ELECTRICAL-BODY AND CHASSIS 8A-341
TROUBLESHOOTING
QUICK CHART FOR CHECK POINT
Check Point Fuse
Door Mirror Door Mirror
Trouble Mode C-11
(10A) Control
Switch LH RH
1. Mirrors on the both sides do not operate
2. Mirror on the left (or right) side does not
operate
3. Mirrors on the both sides operate only in
the vertical
(or horizontal) direction
4. Mirror on the left side operates only in
the vertical
(or horizontal)direction
5. Mirror on the right side operates only in
the vertical
(or horizontal) direction
Cable
Harness
Page 1000 of 4264

8A-342 ELECTRICAL-BODY AND CHASSIS
DOOR MIRROR CONTROL SWITCH
1. Mirrors on the both sides do not operate
Checkpoint Trouble Cause Countermeasure
Reinstall or replace the fuse
No. C-11 (10A)
Poor fuse contact or blown
NG
Repair grounding point
C-2
contact
Grounding point
C-2
Poor grounding point contact
Repair an open circuit or a
poor connection of the
connectors between the fuse
No. C-11 (10A) and 4
D-19
Voltage between the door
mirror control SW. harness
side connector terminal
4
D-19 and the ground
(Should be battery voltage
present)
Open circuit or poor connector
contact
NG NG OK
OK OK
Fuse No. C-11 (10A, Fuse
box)
Repair open circuit or
connector contact
Open circuit or poor connector
contact
NG Continuity between the door
mirror control SW harness
side connector terminal
8
D-19 and C-2
Replace the door mirror
control SW.
Door mirror control SW.
function
SW. malfunction
NG OK
Repair open circuit or
connector contact
Continuity between 7
D-19
and 2
H-24 (or 2 H-25 )
Open circuit or poor connector
contact
NG OK