Page 849 of 4264
ELECTRICAL-BODY AND CHASSIS 8A-191
TROUBLESHOOTING
1. Dome light dose not light
Checkpoint Trouble Cause Countermeasure
Replace the dome light bulb
Burned out the bulb
NG
Repair or replace the dome
light assembly
Dome light switch function
Switch malfunction
Repair open circuit or
connector contact
Continuity between
connector 5
H-12 - 1 L-1
Open circuit or poor connector
contact
NG NG OK
OK
Dome light bulb continuity
2. Dome light does not go out
Repair or replace the door
switch
Switch malfunction or foreign
material switch
NG
Repair short circuit or
connector contact
Continuity between
connector 2
L-1 -ground
when shutting the door
(Should be no continuity)
Short circuit
NG OK
Door switch function (Both
side)
Page 850 of 4264
8A-192 ELECTRICAL-BODY AND CHASSIS
REMOVAL AND INSTALLATION
DOME LIGHT
Removal
1. Remove the dome light lens 1 free.
2. Remove two dome light fixing screws.
3. Remove the wiring connector.
4. Remove the dome light.
5. Pull the bulb
2 to remove it.
Installation
Follow the removal procedure in the reverse order to install the
dome light.
Pay close attention to the important points mentioned in the
following paragraphs.
Bulb
Be absolutely sure that the dome light bulb is correctly
installed.
This will prevent a poor contact and an open circuit.
Page 851 of 4264
ELECTRICAL-BODY AND CHASSIS 8A-193
DOOR SWITCH
Removal
1. Disconnect the battery ground cable.
2. Loosen the screw
1.
3. Remove the door switch.
4. Disconnect the door switch connector
3.
Installation
Follow the removal procedure in the reverse order to install the
spot light.
Pay close attention to the important points mentioned in the
following paragraphs.
Connector
Be absolutely sure that the door switch connector is securely
connected.
This will prevent a poor contact and an open circuit.
SPOT LIGHT (MAP Light)
Removal
1. Grasp the spot light housing
1 with both hands.
Pull the housing straight down.
This will release the clip.
2. Disconnect the connector
2.
3. Turn socket
3 counterclockwise to remove it.
Page 852 of 4264
8A-194 ELECTRICAL-BODY AND CHASSIS
Installation
Follow the removal procedure in the reverse order to install the
spot light.
Pay close attention to the important points mentioned in the
following paragraphs.
Connector
Be absolutely sure that the spot light connector is securely
connected.
This will prevent a poor contact and an open circuit.
Bulb
Be absolutely sure that the spot light bulb is correctly installed.
This will prevent a poor contact and an open circuit.
RTW48ASH000801
WARNING BUZZER (ALARMER
CONTROL UNIT)
Removal
1. Disconnect the battery ground cable.
2. Remove the glove box
Remove the screw.
3. Remove the Alarmer C/U assembly
Remove the screw.
Installation
Follow the removal procedure in the reverse order to install the
warning buzzer.
Pay close attention to the important points mentioned in the
following paragraphs.
Connector
Be absolutely sure that the warning buzzer connector is
securely connected.
This will prevent a poor contact and an open circuit.
Page 853 of 4264
ELECTRICAL-BODY AND CHASSIS 8A-195
INSPECTION AND REPAIR
R-9 R-10
R-1 R-6
DOOR SWITCH
Door Switch Connections
Connector
SW No.
R-9 R-10
R-1 R-6
position Terminal No.
1 Body Ground
PUSHED
RELEASED
WARNING BUZZER
1. Warning Buzzer Circuit
Warning function Operational conditions
Taillights left on The buzzer sounds when both the tail relay and the FRT door switch-drive
side are turned on. To stop the sound of the buzzer, turn on the starter
switch.
Harness side
B-45
2. Warning Buzzer Harness Side Connector Circuit
Disconnect the warning buzzer connector and check
continuity and voltage between the warning buzzer harness
side connector terminals.
Terminal
NO. Wire
color Connecting to Check itemConnecting
terminal Check condition Standard
3 G/R Tail relay 3-Ground Lighting SW “ON” Approx. 12V
6 Y Fuse CB-5 Voltage
6-Ground Starter SW “ON” Approx. 12V
Door SW Open Continuity
(FRT-LH)
Continuity Close No continuity
2 B Ground 2-Ground - Continuity
FRT door-LH 1-Ground 1
B/W
Page 854 of 4264
8A-196 ELECTRICAL-BODY AND CHASSIS
WINDSHIELD WIPER AND WASHER
PARTS LOCATION (RHD)
RTW48AXF0174 & RTW48AXF017501
Page 855 of 4264
ELECTRICAL-BODY AND CHASSIS 8A-197
PARTS LOCATION (LHD)
RTW48AXF017601 & RTW48AXF017701
Page 856 of 4264
8A-198 ELECTRICAL-BODY AND CHASSIS
CIRCUIT DIAGRAM WITHOUT INTERMITTENT RELAY (RHD)
RTW48AXF027901