Page 3321 of 4264

IMMOBILIZER SYSTEM 11A-35
Step Action Value(s) Yes No
10 Review and record for scan tool Failure Records data
and DTCs.
Was the action complete?
Go to Step 11
11 Following the DTC is stored.
Are there DTC B0001 or B0055 stored?
Go to applicable
DTC table after
Go to Step 12 Go to Step 12
12 Clear the DTCs by "Clear the Information "with scan
tool.
Did the DTCs Cleared?
Go to Step 12
13 Select "Display DTCs" with the scan tool.
Are any DTCs stored?
Go to applicable
DTC table Go to Step 14
14 1. Key position is "ON," engine "OFF."
2. Observe the check engine lamp.
Note: If a key switch is turned ON, check engine lamp
will turn on and a check engine lamp will be turned off
after a few seconds.
Is the check engine lamp "flash"?
Go to Step 15
Go to Step 20
15 Check the engine control system.
If a problem is found, repair as necessary.
(Refer to section 6E: system check and DTCs)
IMPORTANT:
The replacement ECM must be
programmed the immobilizer data by scan tool.
(Except 4JA1-L Engine)
Was the action complete?
Go to Step 16
16 Check the key.
Is a key peculiar to a vehicle?
Go to Step 18
Go to Step 17
17 Change into a peculiar key.
IMPORTANT:
If replace the key,
after replace lock
cylinders, perform the following below the items.
Replace the keys and key cylinders.
Program the immobilizer system.
(Refer to "Important information on Programming")
Was the action complete?
Go to Step 18
18 Check the immobilizer programming functions.
Immobilizer control unit (ICU).
Engine control module (ECM).
Transponder (Key).
If a problem is found, repair as necessary.
(Refer to "Important information on Programming")
Was the action complete?
Go to Step 19
19 Operate the DTCs by "Clear the Information" with
scan tool.
Was the action complete?
Go to Step 20
20 Attempt to start the engine.
Did the engine start?
System OK
Refer to
Diagnostic Aids
Page 3322 of 4264

11A-36 IMMOBILIZER SYSTEM
NO IMMOBILIZER WARNING LAMP
Step Action Value(s) Yes No
1 Check the meter fuse for the instrument cluster
ignition feed circuit.
Is the fuse normal?
Go to Step 3
Go to Step 2
2 Replace the fuse.
Is the action complete?
Verify repair
Go to Step 3
3 1. Key position is "OFF".
2. Disconnect the meter.
3. Disconnect the engine control module (ECM).
4. Check the circuit between meter and ECM for an
open, short to round, or short to voltage.
Also, check the meter circuit for an open or short to
ground and the DLC ground circuit for an open.
Was a problem found?
Go to Step 4
Go to Step 5
4 Repair or replace the meter circuit.
Was the action complete?
Go to Step 5
5 1. Key position is "ON," engine "OFF."
2. Observe the check engine lamp.
Is the check engine lamp "ON"?
Go to Step 6
Go to Step 7
6 Repair or replace the meter.
Was the action complete?
Go to Step 7
7 1. Key position is "OFF".
2. Check the check engine lamp bulb.
Is the check engine lamp bulb normal?
Go to Step 9
Go to Step 8
8 Replace the check engine lamp bulb.
Is the action complete?
Verify repair
Go to Step 9
9 1. Key position is "OFF".
2. Connect the meter.
3. Connect the engine control module (ECM).
4. Key position is "ON".
5. Observe the check engine lamp.
Note: If a key switch is turned ON, check engine lamp
will turn on and a check engine lamp will be turned off
after a few seconds.
Is the check engine lamp "ON"?
Verify repair
Go to Step 10
10 Replace the engine control module (ECM).
IMPORTANT: The replacement ICU must be
programmed the immobilizer data by scan tool.
Was the action complete?
Verify repair
Page 3323 of 4264

IMMOBILIZER SYSTEM 11A-37
CHECK IMMOBILIZER WARNING LAMP ON STEADY
Step Action Value(s) Yes No
1 1. Key position is "OFF".
2. Disconnect the immobilizer control unit (ICU).
3. Disconnect the engine control module (ECM).
4. Key position is "ON," engine "OFF."
5. Observe the check engine lamp.
Is the check engine lamp "ON"?
Go to Step 2
Go to Step 5
2 1. Key position is "OFF".
2. Disconnect the meter.
3. Key position is "ON," engine "OFF."
4. Observe the check engine lamp.
Is the check engine lamp "ON"?
Go to Step 3
Go to Step 4
3 Repair or replace the meter.
Was the action complete?
Verify repair
Go to Step 5
4 Repair or replace the meter circuit.
(Between meter and ICU/ECM)
Was the action complete?
Verify repair
Go to Step 5
5 Check the immobilizer control unit (ICU) circuit.
1. Ignition "OFF," disconnect the ICU.
2. Check the ICU circuit for an open, short to ground,
or short to voltage.
Also, check the ICU ignition feed circuit for an open or
short to ground and the ICU ground circuit for an
open.
Was a problem found?
Go to Step 6
Go to Step 7
6 Repair or replace the immobilizer unit (ICU) circuit.
Was the action complete?
Verify repair
Go to Step 7
7 1. Key position is "OFF".
2. Connect the meter.
3. Connect the immobilizer control unit (ICU).
4. Connect the engine control module (ECM).
5. Key position is "ON".
6. Observe the check engine lamp.
Is the check engine lamp "ON"?
Verify repair
Refer to
Diagnostic Aids
Page 3324 of 4264

11A-38 IMMOBILIZER SYSTEM
B0001 REPLACE ELECTRONIC CONTROL UNIT (ECU) (IMMOBILIZER FAULT)
Step Action Value(s) Yes No
1
Was the "Immobilizer System Check" performed?
Go to Step 2
Go to Immobilizer
System Check
2 Recheck the DTC.
1. Key position is “OFF”.
2. Install the scan tool on vehicle.
3. Key position is “ON”.
4. Check the DTC on scan tool.
Is DTC B0001 stored?
Go to Step 3
Refer to
Diagnostic Aids
3 Check the immobilizer control unit (ICU) circuit.
1. Ignition "OFF," disconnect the ICU.
2. Check the ICU circuit for an open, short to ground,
or short to voltage.
Also, check the ICU ignition feed circuit for an open or
short to ground and the ICU ground circuit for an
open.
Was a problem found?
Go to Step 4
Go to Step 5
4 Repair or replace the immobilizer unit (ICU) circuit.
Was the action complete?
Verify repair
5 Replace the immobilizer control unit (ICU).
IMPORTANT: The replacement ICU must be
programmed the security data by scan tool.
Was the action complete?
Verify repair
Page 3325 of 4264

IMMOBILIZER SYSTEM 11A-39
B0002 IMMOBILIZER NOT PROGRAMMED
Step Action Value(s) Yes No
1 Was the "Immobilizer System Check" performed?
Go to Step 2
Go to Immobilizer
System Check
2 Check the immobilizer programming functions.
Immobilizer control unit (ICU).
If a problem is found, repair as necessary.
(Refer to "Important information on Programming")
Was the action complete?
Go to Step 3
Go to Step 5
3 Recheck the DTC.
1. Key position is “OFF” and keep the position for
more than 30 seconds.
2. Key position is “ON”.
3. Check the DTC on scan tool.
Is DTC B0002 stored?
Go to Step 4
Verify repair
4 Replace the immobilizer control unit (ICU).
IMPORTANT:
The replacement ICU must be
programmed the security data by scan tool.
Was the action complete?
Verify repair
5 Check the immobilizer programming functions.
Engine control module (ECM).
Immobilizer control unit (ICU).
If a problem is found, repair as necessary.
(Refer to "Important information on Programming")
Was the action complete?
Verify repair
Go to Step 6
6 Replace the key and lock cylinder assembly and
immobilizer system (ICU and ECM).
IMPORTANT:
ICU and ECM are not replacing simultaneously.
After replace lock cylinders, perform the following
below the items.
Program the immobilizer system.
(Refer to "Important information on Programming")
Was the action complete?
Verify repair
Page 3326 of 4264

11A-40 IMMOBILIZER SYSTEM
B0003 TRANSPONDER KEY PROBLEM
Step Action Value(s) Yes No
1
Was the "Immobilizer System Check" performed?
Go to Step 2
Go to Immobilizer
System Check
2 Check the key.
Is a key peculiar to a vehicle?
Go to Step 3
Refer to
Diagnostic Aids
3 Check the immobilizer programming functions.
All transponder (Key).
If a problem is found, repair as necessary.
(Refer to "Important information on Programming")
Was the action complete?
Go to Step 4
Go to Step 5
4 Recheck the DTC.
1. Key position is “OFF” and keep the position for more
than 30 seconds.
2. Key position is “ON”.
3. Check the DTC on scan tool.
Is DTC B0003 stored?
Go to Step 5
Verify repair
5 Recheck the DTC.
1. Non-OEM parts switch is "OFF" or remove the Non-
OEM parts.
2. Remove the accessory and another key from key.
3. Move the vehicle to a new location.
4. Key position is “OFF” and keep the position for more
than 30 seconds.
5. Key position is “ON”.
6. Check the DTC on scan tool.
Is DTC B0003 stored?
Go to Step 6
Verify repair
6 Check the immobilizer coil (antenna) circuit.
1. Key position is “OFF”.
2. Disconnect the immobilizer control unit (ICU).
(immobilizer coil circuit : 3 pin connector)
3. Check the immobilizer coil circuit for an open, short
to ground, or short to voltage.
Also, check the ICU ignition feed circuit for an open or
short to ground and the ICU ground circuit for an open.
Was a problem found?
Go to Step 7
Go to Step 8
7 Repair or replace the immobilizer coil (antenna) circuit.
Was the action complete?
Verify repair
8 Recheck the DTC.
1. Key position is “OFF” and keep the position for more
than 30 seconds.
2. Key position is “ON”.
3. Check the DTC on scan tool.
Is DTC B0003 stored?
Go to Step 9
Verify repair
Page 3327 of 4264
IMMOBILIZER SYSTEM 11A-41
Step Action Value(s) Yes No
9 Replace the immobilizer control unit (ICU).
IMPORTANT:
The replacement ICU must be
programmed the security data by scan tool.
Was the action complete?
Go to Step 10
10 Check the immobilizer programming functions.
Immobilizer control unit (ICU).
All transponder (Key).
If a problem is found, repair as necessary.
(Refer to "Important information on Programming")
Was the action complete?
Go to Step 11
11 Recheck the DTC.
1. Key position is “OFF” and keep the position for more
than 30 seconds.
2. Key position is “ON”.
3. Check the DTC on scan tool.
Is DTC B0003 stored?
Go to Step 12
Verify repair
12 Replace the transponder (Key).
IMPORTANT:
The replacement transponder (key) must
be programmed the security data by scan tool.
Was the action complete?
Verify repair
Page 3328 of 4264

11A-42 IMMOBILIZER SYSTEM
B0004 IMMOBILIZER COIL CIRCUIT (ANTENNA COIL FAULT)
Step Action Value(s) Yes No
1
Was the "Immobilizer System Check" performed?
Go to Step 2
Go to Immobilizer
System Check
2 Check the immobilizer coil (antenna) circuit.
1. Key position is “OFF”.
2. Disconnect the immobilizer control unit (ICU).
(immobilizer coil circuit : 3 pin connector)
3. Check the immobilizer coil circuit for an open, short
to ground, or short to voltage.
Also, check the ICU ignition feed circuit for an open or
short to ground and the ICU ground circuit for an
open.
Was a problem found?
Go to Step 3
Go to Step 4
3 Repair or replace the immobilizer coil (antenna).
Was the action complete?
Verify repair
4 Recheck the DTC.
1. Key position is “OFF” and keep the position for
more than 30 seconds.
2. Key position is “ON”.
3. Check the DTC on scan tool.
Is DTC B0004 stored?
Go to Step 5
Verify repair
5 Replace the immobilizer control unit (ICU).
IMPORTANT:
The replacement ICU must be
programmed the security data by scan tool.
Was the action complete?
Verify repair