2004 ISUZU TF SERIES Workshop Manual

tire pressure reset glove box towing capacity light catalytic converter power steering fluid

Page 121 of 4264

ISUZU TF SERIES 2004 Workshop Manual RESTRAINT CONTROL 9A1-51

DTC Will Set When
The combined resistance of the driver pretensioner
assembly, harness wiring circuits “Driver Pretensioner
High” and “Driver Pretensioner Low”,

RESTRAINT CONTROL 9A1-51

DTC Will Set When
The combined resistance of the driver pretensioner
assembly, harness wiring circuits “Driver Pretensioner
High” and “Driver Pretensioner Low”, and connector
terminal contact is above a specified value. This test is
run once each ignition cycle during the “Resistance
Measurement Test” when:
1.
No “higher priority faults” are detected during “Turn–
ON”
2.
“Ignition 1” voltage is in the specified value.

Action Taken
SRS control unit turns “ON” the “AIR BAG” warning
lamp and sets DTC B0064.

DTC Will Clear When
The ignition switch is turned “OFF.”

DTC Chart Test Description
Number(s) below refer to circled number(s) on the
diagnostic chart:
2.
This test determines whether the malfunction is in
the SRS control unit.
3.
This test verifies proper connection of the yellow
connector at the base of the driver seat.
4.
This test checks for proper operation of the shorting
clip in the yellow connector.
5.
This test isolate the malfunction to one side of the
SRS coil assembly yellow connector located at the
base of the driver seat.
6.
This test determines whether the malfunction is due
to shortening in the wiring.
7.
This test determines whether the malfunction is in
the driver pretensionerassembly.

Diagnostic Aids
An intermittent condition is likely to be caused by a short
between circuit “Driver Pretensioner High” or “Driver
Pretensioner Low” or a malfunctioning shorting clip on
the driver pretensioner assembly which would require
replacement of the component. The test for this
diagnostic trouble code is only run while the “AIR BAG”
warning lamp is performing the bulb check. When a
scan tool “Clear Codes” command is issued and the
malfunction is still present, the DTC will not reappear
until the next ignition cycle.

DTC B0064 (Flash Code 64) Driver Pretensioner Squib Circuit Low Resistance

Step Action Yes No
1 Perform the “SRS Diagnostic System Check.”
Was the “SRS Diagnostic System Check” performed? Go to Step 2 Go to the “SRS
Diagnostic System
Check”
2

1. Check the driver pretensioner squib circuit for short to voltage
or short to ground.

2. If the problem found, repair as necessary.
Was a problem found? Verify repair Go to Step 3
3

1. Ignition switch “OFF.”

2. Make sure the pretensioner assembly yellow connector
located at the base of the driver seat connected properly.
Is the connector connected properly? Go to Step 4 Seat driver
pretensioner
assembly
connector
properly.
Go to Step 8

Page 122 of 4264

ISUZU TF SERIES 2004 Workshop Manual 9A1-52 RESTRAINT CONTROL SYSTEM

Step Action Yes No
4

1. Disconnect and inspect the pretensioner yellow connector
located base of the driver seat.

2. If ok, reconnect the Pretensioner asse

Page 123 of 4264

ISUZU TF SERIES 2004 Workshop Manual RESTRAINT CONTROL 9A1-53

DTC B0065 (Flash Code 65) Driver Pretensioner Squib Circuit High
Resistance

RTW49JLF000101

Circuit Description
When the ignition switch is turned “ON”, the

Page 124 of 4264

ISUZU TF SERIES 2004 Workshop Manual 9A1-54 RESTRAINT CONTROL SYSTEM

DTC Will Clear When
The ignition switch is turned “OFF”.

DTC Will Set When
The combined resistance of the driver pretensioner
assembly, harness wiring cir

9A1-54 RESTRAINT CONTROL SYSTEM

DTC Will Clear When
The ignition switch is turned “OFF”.

DTC Will Set When
The combined resistance of the driver pretensioner
assembly, harness wiring circuits “Driver Pretensioner
High” and “Driver Pretensioner Low”, and connector
terminal contact is above a specified value. This test
run once each ignition cycle during the “Resistance
Measurement Test” when:
1.
No “higher priority faults” are detected during “Turn–
ON”
2.
“Ignition 1” voltage is in the specified value.

Action Taken
SRS control unit turns “ON” the “AIR BAG” warning
lamp and sets DTC B0065.

DTC Chart Test Description
Number(s) below refer to step number(s) on the
diagnostic chart:
2.
This test determines whether the malfunction is in
the SRS control unit.
3.
This test verifies proper connection of the yellow
connector at the base of the driver seat.
4.
This test checks for proper contact and/or corrosion
of the connector terminals at the base of the drive
r
seat.
5.
This test isolate the malfunction to one side of the
SRS coil assembly yellow connector located at the
base of the driver seat.
6.
This test determines whether the malfunction is due
to high resistance in the wiring.
7.
This test determines whether the malfunction is in
the driver pretensioner assembly.

Diagnostic Aids
An intermittent condition is likely to be caused by a poor
connection at the drive pretensioner harness connecto
r
terminals “1” and “2”, SRS control unit terminals “42”
and “41”, or a poor wire to terminal connection in circuit
“Driver Pretensioner High” or “Driver Pretensioner Low”
The test for this diagnostic trouble code is only run while
the “AIR BAG” warning lamp is performing the bulb
check. When a scan tool “Clear Codes” command is
issued and the malfunction is still present, the DTC will
not reappear until the next ignition cycle.

DTC B0065 (Flash Code 65) Driver Pretensioner Squib Circuit High Resistance

Step Action Yes No
1 Perform the “SRS Diagnostic System Check”.
Was the “SRS Diagnostic System Check” performed? Go to Step 2 Repeat the “SRS
Diagnostic System
Check”
2

1. Check the driver pretensioner squib circuit for open.

2. If the problem found repair as necessary.
Was a problem found? Verify repair Go to Step 3
3

1. Ignition switch “OFF.”

2. Disconnect SRS coil assembly yellow connector located at
base of the driver seat.
Is the connector connected properly? Go to Step 4 Seat pretensioner
assembly
connector
properly.
Go to Step 8

Page 125 of 4264

ISUZU TF SERIES 2004 Workshop Manual RESTRAINT CONTROL 9A1-55

Step Action Yes No
4

1. Disconnect and inspect the pretensioner assembly yellow
connector located base of the driver seat.

2. If ok, reconnect the pretensioner y

Page 126 of 4264

ISUZU TF SERIES 2004 Workshop Manual 9A1-56 RESTRAINT CONTROL SYSTEM

DTC B0066 (Flash Code 66) Driver Pretensioner Squib Circuit Voltage
Range/Performance

RTW49JLF000101

Circuit Description
When the ignition switch is tur

Page 127 of 4264

ISUZU TF SERIES 2004 Workshop Manual RESTRAINT CONTROL 9A1-57

DTC Will Clear When
The malfunction is no longer occurring and the ignition
is turned “OFF”.

DTC Chart Test Description
Number(s) below refer to step number(s) on

RESTRAINT CONTROL 9A1-57

DTC Will Clear When
The malfunction is no longer occurring and the ignition
is turned “OFF”.

DTC Chart Test Description
Number(s) below refer to step number(s) on the
diagnostic chart:
2.
This test determines whether the SRS control unit is
malfunctioning
3.
This test isolates the malfunction to one side of the
pretensioner assembly yellow connector at the base
of the driver seat.
4.
This test determines whether the malfunction is in
“Driver Pretensioner High” circuit.
5.
This test determines whether the malfunction is in
“Driver Pretensioner Low” circuit.
6.
This test determines whether the malfunction is in
“Driver Pretensioner High” circuit.
7.
This test determines whether the malfunction is in
“Driver Pretensioner Low” circuit.
8.
This test determines whether the malfunction is in
the driver pretensioner assembly.
Diagnostic Aids
An intermittent condition is likely to be caused by a short
to ground/+B in the driver pretensioner circuit. Inspect
circuits “Driver Pretensioner High” and “Driver
Pretensioner Low” carefully for cutting or chafing.

DTC B0066 (Flash Code 66) Driver Pretensioner Squib Circuit Voltage Range/Performance

Step Action Yes No
1 Was the “SRS Diagnostic System Check” performed? Go to Step 2 Go to the “SRS
Diagnostic System
Check”
2

1. When measurements are requested in this chart use 5-8840-
0285-0 DVM with correct terminal adapter from 5-8840-
0385-0.

2. Ignition switch “OFF.”
3. Ignition switch “ON.”

4. Check the driver pretensioner squib circuit for short to
voltage, short to ground and open.
Was a problem found? Verify repair Go to Step 3
3

1. Ignition switch “OFF.”

2. Disconnect pretensioner yellow connector located at base of
the driver seat. leave passenger pretensioner assembly
connected.

3. Connect SRS driver / passenger load tool 5-8840-2421-0 and
appropriate adapter to pretensioner harness connector.

4. ignition switch “ON.”
Is DTC B0066 current? Go to Step 4 Go to Step 8
4

1. Ignition switch “OFF.”

2. Disconnect SRS control unit.
3. Disconnect SRS driver / passenger load tool.

4. Measure resistance on SRS control unit harness connector
“42” to terminal “40” (ground).
Does 5-8840-0285-0 display “OL” (infinite)? Go to Step 5 Replace SRS
harness or repair
chassis harness.
Go to Step 9

Page 128 of 4264

ISUZU TF SERIES 2004 Workshop Manual 9A1-58 RESTRAINT CONTROL SYSTEM

Step Action Yes No
5 Measure resistance on SRS control unit harness connector from
terminal “41” to terminal “40” (ground).
Does 5-8840-0285-0 displa

Load next 8 pages

Page: < prev 1-10 ... 89-96 97-104 105-112 113-120 121-128 129-136 137-144 145-152 153-160 ... 4264 next >

load capacity inflation pressure brake fluid clock fuel filter location fuel reserve