Page 14 of 4264
9-12 ACCESSORIES
RADIO
REMOVAL AND INSTALLATION
RTW48AMF000201
Removal
1. Remove the ash try
2. Remove the HVAC control
3. Remove the 2 crews unit on the HVAC
4. Remove the center cluster cover assembly
5. Remove the ash try bracket
6. Disconnect the connector for Audio
8. Remove the 4 screws on the radio
8. Disconnect the Antenna feeder plug
9. Pull out the radio
Installation
To install, follow the removal steps in the reverse order.
Page 15 of 4264
ACCESSORIES 9-13
FRONT SPEAKER
REMOVAL AND INSTALLATION
Removal
1. Remove the Door Trim Panel
Refer to section 10 “FRONT DOOR ASSEMBLY”fo
r
door trim panel removal steps.
2. Remove the Front Speaker
Remove the screw.
Disconnect the connector.
Installation
To install, follow the removal steps in the reverse order.
Page 16 of 4264
9-14 ACCESSORIES
TWEETER
REMOVAL AND INSTALLATION
RTW390SH000101
Removal
1. Remove the Door Trim Panel
Refer to section 10 “FRONT DOOR ASSEMBLY”fo
r
door trim panel removal steps.
2. Remove the Tweeter
Remove the three screws.
Disconnect the connector.
Installation
To install, follow the removal steps in the reverse order.
Page 17 of 4264
ACCESSORIES 9-15
REAR SPEAKER (EXTEND CAB)
REMOVAL AND INSTALLATION
Removal
1. Remove the Speaker Grille
Pull the grille to release the locks.
2. Remove the Rear Speaker
Remove the three screws.
Disconnect the connector.
Installation
To install, follow the removal steps in the reverse order.
Page 18 of 4264
9-16 ACCESSORIES
REAR SPEAKER (CREW CAB)
REMOVAL AND INSTALLATION
RTW390MH000101
Removal
1. Remove the Rear Door Trim Panel
Refer to section 10 “REAR DOOR ASSEMBLY”for doo
r
trim panel removal steps.
2. Remove the Rear Speaker
Remove the screw.
Disconnect the connector.
Installation
To install, follow the removal steps in the reverse order.
Page 19 of 4264
ACCESSORIES 9-17
CLOCK
REMOVAL AND INSTALLATION
Removal
1. Remove the center cluster ASM
2. Disconnect the connector.
3. Remove the clock.
Installation
To install, follow the removal steps in the reverse order.
Page 20 of 4264
9-18 ACCESSORIES
ANTENNA
REMOVAL AND INSTALLATION
Removal
1. Remove the antenna screw 1.
2. Disconnect the feeder cable
3 connector
.
3. Remove the antenna cable
2 .
4. Pull out antenna downward.
Remove and install the antenna as illustrated.
Antenna unit is located on the roof panel driver side.
To install, follow the removal steps in the reverse order.
Installation
To install, follow the removal steps in the reverse order.
Page 131 of 4264
RESTRAINT CONTROL 9A1-61
DTC B1000 (Flash Code 72) SDM Internal Fault (SDM=SRS control unit)
RTW49JLF000101
Circuit Description
DTC B1000 is an indication of a potential internal SRS
control unit malfunction and will set if any of the
following conditions are detected:
1) Microprocessor energy reverse time failure.
2) EEPROM read / write failure.
3) ROM check sum.
4) Calibration check sum fault.
5) Inflators reserve voltage low.
6) Inflators electronic sensor active signal not detected
during commanded deployment.
7) QSDD (High-side/Low-side) FET failure.
8) Frontal accelerometer failure.
9) Phase lock loop lost lock.
10) QSDD communication fault.
DTC Will Set When
Any of the above indicated malfunctions are detected by
the SRS control unit. The malfunctions described
above are tested mainly during “Continuous Monitoring”
and some ones run each ignition cycle.
Action Taken
SRS control unit turns “ON” the “AIR BAG” warning
lamp and sets a diagnostic trouble code.
DTC Will Clear When
SRS control unit is replaced.
