Page 2385 of 4500
Fig. 79: Identifying Speed Sensor Rear LH Bolt
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
27.INSTALL REAR AXLE SHAFT NUT
a. While applying brakes, use a socket wrench (32 mm) to install the nut.
Torque: 290 N.m, (2,960 kgf.cm, 214 ft.lbf)
b. Install the lock cap and a new cotter pin.
If the holes for the cotter pin are not ali
gned, tighten the nut a further 10°.
Page 2386 of 4500
Fig. 80: Installing Rear Axle Shaft Nut
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
28.INSTALL PARKING BRAKE CABLE ASSY NO. 3
a. Install the parking brake cable assy to the body with the 2 bolts.
Torque: 19 N.m (194 kgf.cm, 14 ft.lbf)
Page 2387 of 4500
Fig. 81: Identifying Parking Brake Cable Assy No. 3 Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
29.INSTALL REAR SUSPENSION MEMBER BRACE LH
a. Install the rear suspension member brace to the body with the 2 bolts.
Torque: 50 N.m (510 kgf.cm, 37 ft.lbf)
Page 2388 of 4500
<0029004c004a00110003001b0015001d0003002c0047004800510057004c0049005c004c0051004a0003003500480044005500030036005800560053004800510056004c005200510003003000480050004500480055000300250055004400460048000300
2f002b000300250052004f00570056[
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
30.INSTALL DIFFERENTIAL SUPPORT PROTECTOR NO. 2
a. Install the differential support protector No. 2 to the body with the 3 nuts.
Torque: 5.4 N.m (55 kgf.cm, 48 in.lbf)
Page 2389 of 4500
Fig. 83: Identifying Differential Support Protector No. 2 Nuts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
31.INSTALL REAR STABILIZER LINK ASSY LH
a. Install the stabilizer link assy LH with the nut.
Torque: 65 N.m (663 kgf.cm, 48 ft.lbf)
HINT:
If the ball
joint turns together with the nut, use a hexagon (6 mm) wrench to hold the stud.
Page 2390 of 4500
Fig. 84: Installing Rear Stabilizer Link Assy LH Nut
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
32.INSTALL HEIGHT CONTROL SENSOR LINK SUB-ASSY REAR
a. Align the matchmarks and connect the height control sensor link to the rear suspension arm assy
No.2 LH.
b. Install and torque the 6 bolts, washers and nuts.
Torque: 5.4 N.m (55 kgf.cm, 48 in.lbf)
Page 2391 of 4500
Fig. 85: Aligning Matchmarks
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
33.INSTALL REAR TIRE
Torque: 103 N.m (1,050 kgf.cm, 76 ft.lbf)
34.ADJUST VEHICLE HEIGHT (W/ AIR SUSPENSION) (See ON
-VEHICLE INSPECTION )
35.INSPECT HEADLIGHT AIM ONLY (See ADJUSTMENT
)
36.INSPECT AND ADJUST REAR WHEEL ALIGNMENT (See ADJUSTMENT
)
37.CHECK ABS SPEED SENSOR SIGNAL (See TEST MODE PROCEDURE
)
REPLACEMENT
HINT:
See COMPONENTS
<00380056004800030057004b00480003005600440050004800030053005500520046004800470058005500480056000300490052005500030057004b004800030035002b00030056004c0047004800030044005100470003002f002b00030056004c004700
4800110003[
Page 2392 of 4500

The procedures listed below are for the LH side.
1.REMOVE REAR TIRE
2.SEPARATE HEIGHT CONTROL SENSOR LINK SUB-ASSY REAR (See REPLACEMENT
)
3.REMOVE REAR AXLE SHAFT NUT (See REPLACEMENT
)
4.REMOVE REAR DISC BRAKE CALIPER ASSY LH (See REPLACEMENT
)
5.REMOVE REAR DISC
6.SEPARATE SPEED SENSOR REAR LH (See REPLACEMENT
)
7.REMOVE PARKING BRAKE SHOE RETURN TENSION SPRING (See step 5 on OVERHAUL
)
SST 09703-30010
8.REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET (See OVERHAUL
)
9.REMOVE PARKING BRAKE SHOE ASSY LH NO. 1 (See step 6 on OVERHAUL
)
SST 09718-00010
10.REMOVE PARKING BRAKE SHOE ASSY LH NO. 2 (See step 7 on OVERHAUL
)
SST 09718-00010
11.REMOVE PARKING BRAKE SHOE LEVER SUB-ASSY LH (See step 10 on OVERHAUL
)
12.REMOVE PARKING BRAKE CABLE ASSY NO. 3 (See step 11 on REPLACEMENT
)
13.REMOVE PARKING BRAKE ANCHOR BLOCK SUB-ASSY (See step 13 on OVERHAUL
)
14.SEPARATE TOE CONTROL LINK SUB-ASSY LH
a. Remove the nut.
b. Using SST, disconnect the toe control link LH from the rear axle carrier.
SST 09628-00011