Page 4521 of 5267
B-PILLAR UPPER TRIM
REMOVAL
REGULAR CAB
1. Remove the cap (1) and then the bolt (2) that
secures the seat belt (3) to the top of the B-pillar
(4) and position the seat belt out of the way.
2. Using a trim stick C-4755 or equivalent, disengage
the retaining tabs that secure the upper B-pillar trim
panel (5) to the B-pillar and remove the trim panel.
QUAD CAB
1. Using a small flat-bladed tool, carefully open the
two fastener covers (2) located on the grab handle
(1).
2. Remove the two bolts (3) that secure the grab han-
dle to the B-pillar and remove the grab handle.
Page 4522 of 5267
3. Remove the cap (1) and the bolt (2) that secures
the seat belt (3) to the top of the B-pillar (4) and
position the seat belt out of the way.
4. Using a trim stick C-4755 or equivalent, disengage
the retaining tabs that secure the upper B-pillar trim
panel (5) to the B-pillar and remove the trim panel.
INSTALLATION
REGULAR CAB
1. Position the upper B-pillar trim panel (5) to the
B-pillar (4).
2. Engage the retaining tabs that secure the upper
B-pillar trim panel to the B-pillar.
3. Install the bolt (2) that secures the seat belt (3) to
the top of the B-pillar. Tighten the bolt to 40 Nꞏm
(30 ft. lbs.).
4. Install the cap (1) onto the seat belt.
Page 4523 of 5267
QUAD CAB
1. Position the upper B-pillar trim panel (5) to the
B-pillar (4).
2. Engage the retaining tabs that secure the upper
B-pillar trim panel to the B-pillar.
3. Install the bolt (2) that secures the seat belt (3) to
the top of the B-pillar. Tighten the bolt to 40 Nꞏm
(30 ft. lbs.).
4. Install the cap (1) onto the seat belt.
5. Install the grab handle (1) onto the B-pillar and
install the two bolts (3). Tighten the bolts to 6 Nꞏm
(55 in. lbs.).
6. Close the two fastener covers (2) located on the
grab handle.
Page 4524 of 5267
C-PILLAR LOWER TRIM
REMOVAL
1. Remove the upper C-pillar trim panel (Refer to 23 -
BODY/INTERIOR/C-PILLAR TRIM - REMOVAL).
2. Remove the bolt (3) that secures the seat belt (2)
to the bottom of the C-pillar (4) and position the
seat belt out of the way.
3. Using a trim stick C-4755 or equivalent, disengage
the retaining tabs that secure the lower C-pillar trim
panel (1) to the C-pillar.
4. Remove the seat belt from the lower C-pillar trim
panel through the slot provided and remove the
trim panel.
INSTALLATION
1. Route the seat belt (2) through the slot in the lower
C-pillar trim panel (1) and position the trim panel to
the C-pillar (4).
2. Engage the retaining tabs that secure the lower
C-pillar trim panel to the C-pillar.
3. Install the bolt (3) that secures the seat belt to the
bottom of the C-pillar. Tighten the bolt to 40 Nꞏm
(30 ft. lbs.).
4. Install the upper C-pillar trim panel (Refer to 23 -
BODY/INTERIOR/C-PILLAR UPPER TRIM -
INSTALLATION).
Page 4525 of 5267
C-PILLAR UPPER TRIM
REMOVAL
1. Remove the cap (1) and then the bolt (2) that
secures the seat belt (3) to the top of the C-pillar
(4) and position the seat belt out of the way.
2. Using a trim stick C-4755 or equivalent, disengage
the retaining tabs that secure the upper C-pillar
trim panel (5) to the C-pillar and remove the trim
panel.
INSTALLATION
1. Position the upper C-pillar trim panel (5) to the
C-pillar (4).
2. Engage the retaining tabs that secure the upper
C-pillar trim panel to the C-pillar.
3. Install the bolt (2) that secures the seat belt (3) to
the top of the C-pillar. Tighten the bolt to 40 Nꞏm
(30 ft. lbs.).
4. Install the cap (1) onto the seat belt.
Page 4526 of 5267
CARPETS AND FLOOR MATS
REMOVAL
NOTE: Carpet for Quad Cab model shown. Regular cab similar.
1. Remove the front seats (Refer to 23 - BODY/
SEATS/SEAT - FRONT - REMOVAL).
2. If equipped, remove the floor console (Refer to 23 -
BODY/INTERIOR/FLOOR CONSOLE -
REMOVAL).
3. If equipped, remove the three bolts (1) that secure
the rear storage compartment (2) to the floor panel
(3) and remove the storage compartment from the
rear trim panel (4).
4. On Quad Cab models, remove the rear seats (1)
(Refer to 23 - BODY/SEATS/SEAT - REAR -
REMOVAL).
5. On Quad Cab models, remove the rear cup holder
(2) using a trim stick C-4755 or equivalent.
Page 4527 of 5267
6. Remove the lower B-pillar trim panels (Refer to 23
- BODY/INTERIOR/B-PILLAR LOWER TRIM -
REMOVAL).
7. On Quad Cab models, remove the bolt that
secures the lower seat belt anchor to the floor
panel near the B-pillars (Refer to 8 - ELECTRICAL/
RESTRAINTS/SEAT BELT & RETRACTOR -
REMOVAL).
8. Remove the retaining screw (1) that secures the
jack assembly (2) to the floor panel (3) and remove
the jack assembly.
9. Remove the two bolts (4) that secure the jack
assembly to the floor panel.
10. For trucks equipped with a scissor type jack,
remove the bolts (1) and remove the jack (2).
11. Remove the screws and remove the load floor
storage strap snaps (1).
Page 4528 of 5267
12. On Quad Cab models, remove the eleven push-
pin fasteners (1) that secure the rear of the carpet
(2) to the floor panel (3).
13. Remove the carpet from the vehicle.
INSTALLATION
NOTE: Carpet for Quad Cab model shown. Regular cab similar.
1. Position the carpet (2) into the vehicle.
2. On Quad Cab models, install the eleven push-pin
fasteners (1) that secure the carpet to the floor
panel (3).
3. Install the load floor storage snaps and screws (1).