Page 4529 of 5267
4. On trucks equipped with a scissor jack, install the
jack and install the bolts (1).
5. Install the two bolts (4) that secure the jack assem-
bly (2) to the floor panel (3).
6. Position the jack assembly onto the two bolts and
install the retaining screw (1). Tighten the screw
securely.
7. On Quad Cab models, install the bolt that secures
the lower seat belt anchors the floor panel near the
B-pillars (Refer to 8 - ELECTRICAL/RESTRAINTS/
SEAT BELT & RETRACTOR - INSTALLATION).
Tightentheboltto40Nꞏm(30ft.lbs.).
8. Install the lower B-pillar trim panels (Refer to 23 -
BODY/INTERIOR/B-PILLAR LOWER TRIM -
INSTALLATION).
9. On Quad Cab models, install the rear seat (1)
(Refer to 23 - BODY/SEATS/SEAT - INSTALLA-
TION).
10. On Quad Cab models, install the rear cup holder
(2).
Page 4530 of 5267
11. If equipped, position the rear storage compartment
(2) onto the rear cab trim panel (4) and install the
three bolts (1). Tighten the bolts to 6 Nꞏm (55 in.
lbs.).
12. If equipped, install the floor console (Refer to 23 -
BODY/INTERIOR/FLOOR CONSOLE - INSTAL-
LATION).
13. Install the front seats (Refer to 23 - BODY/
SEATS/SEAT - FRONT - INSTALLATION).
Page 4531 of 5267
COAT HOOK
REMOVAL
1. Using a trim stick C-4755 or equivalent, disengage
the release clip (2) as shown and remove the coat
hook (1) from the headliner (3)
INSTALLATION
1. Position the coat hook (1) through the headliner (3)
and fully seat the base of the support to the roof
panel.
2. Engage the release clip (2).
Page 4532 of 5267
COWL TRIM
REMOVAL
1. Using a trim stick C-4755 or equivalent, disengage
the retaining tabs of the cowl trim panel (1) from
the retainer clips (2) in the door sill (3).
2. Pull the cowl trim panel rearward and remove it
from the vehicle.
INSTALLATION
1. Position the cowl trim panel (1) onto the door sill
(3).
2. Push the cowl trim panel forward and then engage
the retaining tabs that secure the sill trim panel to
the rear door sill.
Page 4533 of 5267
FLOOR CONSOLE
REMOVAL
Mini Floor Console
1. If equipped, remove the 4WD gear shift boot (Refer
to 23 - BODY/INTERIOR/4WD FLOOR SHIFT
BOOT - REMOVAL).
2. If equipped with a manual transmission, remove
the transmission gear shift lever extension.
3. Remove the console inserts, if equipped.
4. Remove the bolts (2) that secure the rear console
(1) to the floor panel.
5. Lift up the rear of the floor console to clear the
gear shift lever, if equipped.
Page 4534 of 5267
6. Remove the bolts (2) and separate the front con-
sole (3) from the floor.
7. Separate the front clips (1) and remove the mini
console.
Full Floor Console
1. Before proceeding with the following repair proce-
dure, review all warnings and cautions. (Refer to
23 - BODY/SEATS - WARNING)
2. Using a trim stick C-4755 or equivalent, separate
the seven front console bezel clips (2), lift up the
back of the bezel (1) and remove.
Page 4535 of 5267
3. Remove the bolts (1) and lift the rear of the base
up to release the front guide pins (5).
4. Remove the front base (2).
NOTE: Do not reuse the seat fasteners, always
replace with new ones.
5. Remove and discard the front bolts (4).
6. Position the seats forward, remove the rear bolts
(2) and discard.
7. Disconnect the 12v power supply electrical connec-
tor (3 - if equipped).
8. Fold the seat backs forward and roll the seat
assembly (1) back in the vehicle.
9. Remove the nuts (2) attaching the center seat con-
sole (1) to the drivers seat and the passenger seat
and discard.
Page 4536 of 5267
10. Remove the nuts (4) attaching the center console
(2) to the drivers seat (3) and the passenger seat
in the rear of the seat and discard.
11. Disconnect the electrical connector (1 - if
equipped).
12. Roll the seat assembly forward and remove the
center seat console.
INSTALLATION
Mini Floor Console
1. Position the console and seat the front clips (1)
fully.
2. Install the bolts (2).