Page 1753 of 4179
DTC P0341 CMP SENSOR
EC-1375
[YD (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
MA
EC
Component InspectionEBS0121Z
CAMSHAFT POSITION SENSOR
1. Loosen the fixing bolt of the sensor.
2. Disconnect camshaft position sensor harness connector.
3. Remove the sensor.
4. Visually check the sensor for chipping.
5. Check resistance as shown in the figure.
6. If NG, replace camshaft position sensor.
Removal and InstallationEBS01220
CAMSHAFT POSITION SENSOR
Refer to EM-153, "VACUUM PUMP" .
MBIB0647E
Terminal No. (Polarity) ResistanceΩ [at 25°C (77°F)]
1 (+) - 2 (-)
Except 0
1 (+) - 3 (-)
2 (+) - 3 (-) Except 0 or ∞
MBIB1009E
Page 1754 of 4179
![NISSAN X-TRAIL 2003 Service Repair Manual EC-1376
[YD (WITHOUT EURO-OBD)]
DTC P0563 BATTERY VOLTAGE
DTC P0563 BATTERY VOLTAGEPFP:24410
On Board Diagnosis LogicEBS01221
The MI will not light up for this self-diagnosis.
DTC Confirmation Proce NISSAN X-TRAIL 2003 Service Repair Manual EC-1376
[YD (WITHOUT EURO-OBD)]
DTC P0563 BATTERY VOLTAGE
DTC P0563 BATTERY VOLTAGEPFP:24410
On Board Diagnosis LogicEBS01221
The MI will not light up for this self-diagnosis.
DTC Confirmation Proce](/manual-img/5/57404/w960_57404-1753.png)
EC-1376
[YD (WITHOUT EURO-OBD)]
DTC P0563 BATTERY VOLTAGE
DTC P0563 BATTERY VOLTAGEPFP:24410
On Board Diagnosis LogicEBS01221
The MI will not light up for this self-diagnosis.
DTC Confirmation ProcedureEBS01222
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
WITH CONSULT-II
1. Turn ignition switch ON.
2. Select “DATA MONITOR” mode with CONSULT-II.
3. Start engine and let it idle for at least 35 seconds.
4. If DTC is detected, go to EC-1376, "
Diagnostic Procedure" .
Diagnostic ProcedureEBS01223
1. INSPECTION START
Are jumper cables connected for the jump starting?
Ye s o r N o
Yes >> GO TO 3.
No >> GO TO 2.
2. CHECK BATTERY AND ALTERNATOR
Check that the proper type of battery and alternator is installed.
Refer to SC-3, "
BATTERY" and SC-12, "CHARGING SYSTEM" .
OK or NG
OK >> GO TO 5.
NG >> Replace with a proper one.
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
P0563 Battery voltage highAn excessively high voltage from the battery is
sent to ECM.
Battery
Battery terminal
Alternator
SEF817Y
Page 1755 of 4179
![NISSAN X-TRAIL 2003 Service Repair Manual DTC P0563 BATTERY VOLTAGE
EC-1377
[YD (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
MA
EC
3. CHECK JUMPER CABLES INSTALLATION
Check that the jumper cables are connected in the correct sequence.
OK or NG
O NISSAN X-TRAIL 2003 Service Repair Manual DTC P0563 BATTERY VOLTAGE
EC-1377
[YD (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
MA
EC
3. CHECK JUMPER CABLES INSTALLATION
Check that the jumper cables are connected in the correct sequence.
OK or NG
O](/manual-img/5/57404/w960_57404-1754.png)
DTC P0563 BATTERY VOLTAGE
EC-1377
[YD (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
MA
EC
3. CHECK JUMPER CABLES INSTALLATION
Check that the jumper cables are connected in the correct sequence.
OK or NG
OK >> GO TO 4.
NG >> Reconnect jumper cables properly.
4. CHECK BATTERY FOR BOOSTER
Check that the battery for the booster is a 12V battery.
OK or NG
OK >> GO TO 5.
NG >> Change the vehicle for booster.
5. PERFORM DTC CONFIRMATION PROCEDURE AGAIN
Perform EC-1376, "
DTC Confirmation Procedure" , again.
OK or NG
OK >> GO TO 7.
NG >> GO TO 6.
6. REPLACE ECM
1. Replace ECM.
2. Perform initialization of NATS system and registration of all NATS ignition key IDs. Refer to EC-1224,
"NATS (Nissan Anti-theft System)" .
3. Perform Fuel Pump Learning Value Clearing. Refer to EC-1221, "
Fuel Pump Learning Value Clearing" .
>>INSPECTION END
7. CHECK ELECTRICAL PARTS DAMAGE
Check the following for damage.
Wiring harness and harness connectors for burn
Fuses for short
OK or NG
OK >>INSPECTION END
NG >> Repair or replace malfunctioning part.
SEF439Z
Page 1756 of 4179
![NISSAN X-TRAIL 2003 Service Repair Manual EC-1378
[YD (WITHOUT EURO-OBD)]
DTC P0605 ECM
DTC P0605 ECMPFP:23710
DescriptionEBS01224
The ECM consists of a microcomputer and connectors for signal
input and output and for power supply. The ECM NISSAN X-TRAIL 2003 Service Repair Manual EC-1378
[YD (WITHOUT EURO-OBD)]
DTC P0605 ECM
DTC P0605 ECMPFP:23710
DescriptionEBS01224
The ECM consists of a microcomputer and connectors for signal
input and output and for power supply. The ECM](/manual-img/5/57404/w960_57404-1755.png)
EC-1378
[YD (WITHOUT EURO-OBD)]
DTC P0605 ECM
DTC P0605 ECMPFP:23710
DescriptionEBS01224
The ECM consists of a microcomputer and connectors for signal
input and output and for power supply. The ECM controls the engine.
On Board Diagnosis LogicEBS01225
DTC Confirmation ProcedureEBS01226
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
WITH CONSULT-II
1. Turn ignition switch ON.
2. Select “DATA MONITOR” mode with CONSULT-II.
3. Wait at least 5 seconds.
4. If 1st trip DTC is detected, go to EC-1378, "
Diagnostic Proce-
dure" .
Diagnostic ProcedureEBS01227
1. INSPECTION START
With CONSULT-II
1. Turn ignition switch ON.
2. Select “SELF DIAG RESULTS” mode with CONSULT-II.
3. Touch “ERASE”.
4. Perform EC-1378, "
DTC Confirmation Procedure" , again.
5. Is 1st trip DTC P0605 displayed again?
Ye s o r N o
Yes >> GO TO 2.
No >>INSPECTION END
MBIB0625E
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
P0605Engine control module
(ROM)ECM ROM is malfunctioning.
ECM
SEF817Y
Page 1757 of 4179
DTC P0605 ECM
EC-1379
[YD (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
MA
EC
2. REPLACE ECM
1. Replace ECM.
2. Perform initialization of NATS system and registration of all NATS ignition key IDs. Refer to EC-1224,
"NATS (Nissan Anti-theft System)" .
3. Perform Fuel Pump Learning Value Clearing. Refer to EC-1221, "
Fuel Pump Learning Value Clearing" .
>>INSPECTION END
Page 1758 of 4179
![NISSAN X-TRAIL 2003 Service Repair Manual EC-1380
[YD (WITHOUT EURO-OBD)]
DTC P0606 ECM
DTC P0606 ECMPFP:23710
DescriptionEBS01228
The ECM consists of a microcomputer and connectors for signal
input and output and for power supply. The ECM NISSAN X-TRAIL 2003 Service Repair Manual EC-1380
[YD (WITHOUT EURO-OBD)]
DTC P0606 ECM
DTC P0606 ECMPFP:23710
DescriptionEBS01228
The ECM consists of a microcomputer and connectors for signal
input and output and for power supply. The ECM](/manual-img/5/57404/w960_57404-1757.png)
EC-1380
[YD (WITHOUT EURO-OBD)]
DTC P0606 ECM
DTC P0606 ECMPFP:23710
DescriptionEBS01228
The ECM consists of a microcomputer and connectors for signal
input and output and for power supply. The ECM controls the engine.
On Board Diagnosis LogicEBS01229
DTC Confirmation ProcedureEBS0122A
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
WITH CONSULT-II
1. Turn ignition switch ON.
2. Select “DATA MONITOR” mode with CONSULT-II.
3. Wait at least 5 seconds.
4. If DTC is detected, go to EC-1380, "
Diagnostic Procedure" .
Diagnostic ProcedureEBS0122B
1. INSPECTION START
With CONSULT-II
1. Turn ignition switch ON.
2. Select “SELF DIAG RESULTS” mode with CONSULT-II.
3. Touch “ERASE”.
4. Perform EC-1380, "
DTC Confirmation Procedure" , again.
5. Is 1st trip DTC P0606 displayed again?
Ye s o r N o
Yes >> GO TO 2.
No >>INSPECTION END
MBIB0625E
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
P0606Engine control module
(Processor)ECM calculation function is malfunctioning.
ECM
SEF817Y
Page 1759 of 4179
DTC P0606 ECM
EC-1381
[YD (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
MA
EC
2. REPLACE ECM
1. Replace ECM.
2. Perform initialization of NATS system and registration of all NATS ignition key IDs. Refer to EC-1224,
"NATS (Nissan Anti-theft System)" .
3. Perform “Fuel Pump Learning Value Clearing”. Refer to EC-1221, "
Fuel Pump Learning Value Clearing" .
>>INSPECTION END
Page 1760 of 4179
![NISSAN X-TRAIL 2003 Service Repair Manual EC-1382
[YD (WITHOUT EURO-OBD)]
DTC P0628, P0629 FUEL PUMP
DTC P0628, P0629 FUEL PUMPPFP:16700
DescriptionEBS0122C
To control the amount of the fuel inhalation of the fuel pump, a plunger is built i NISSAN X-TRAIL 2003 Service Repair Manual EC-1382
[YD (WITHOUT EURO-OBD)]
DTC P0628, P0629 FUEL PUMP
DTC P0628, P0629 FUEL PUMPPFP:16700
DescriptionEBS0122C
To control the amount of the fuel inhalation of the fuel pump, a plunger is built i](/manual-img/5/57404/w960_57404-1759.png)
EC-1382
[YD (WITHOUT EURO-OBD)]
DTC P0628, P0629 FUEL PUMP
DTC P0628, P0629 FUEL PUMPPFP:16700
DescriptionEBS0122C
To control the amount of the fuel inhalation of the fuel pump, a plunger is built into the fuel pump. When the
amount of the fuel inhalation of fuel increases, the fuel pump raises the fuel exhalation pressure. As a result,
the fuel injection pressure is raised. When the load of the engine increases, the ECM sends a signal to the fuel
pump to raise the injection pressure.
CONSULT-II Reference Value in Data Monitor ModeEBS0122D
Specification data are reference values.
ECM Terminals and Reference ValueEBS0122E
Specification data are reference values and are measured between each terminal and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
MONITOR ITEM CONDITION SPECIFICATION
PUMP CURRENT
Engine: After warming up
Air conditioner switch: OFF
Shift lever: Neutral position
No-loadIdle 1,700 - 1,900 mA
2,000 rpm 1,600 - 1,800 mA
TERMI-
NAL
NO.WIRE
COLORITEM CONDITIONDATA
(DC Voltage and Pulse Signal)
10 Y/L Fuel pump power supply[Engine is running]
Warm-up condition
Idle speed0 - 12.5V
[Engine is running]
Warm-up condition
Engine speed is 2,000 rpm0 - 12.5V
29 L Fuel pump[Engine is running]
Warm-up condition
Idle speed0.5 - 1.0V
[Engine is running]
Warm-up condition
Engine speed is 2,000 rpm0.5 - 1.0V
MBIB0885E
MBIB0886E
MBIB0887E
MBIB0888E