Page 3321 of 4179
DOOR OUTSIDE MOLDING
EI-23
C
D
E
F
G
H
J
K
L
MA
B
EI
5. Reaching from inner side of door, use a clip clamp tool to disen-
gage rear door outside molding from the pawl.
NOTE:
Insert clip clamp tool into the door pawl, then disengage by
pressing in the direction of arrow. (See figure on the right.)
INSTALLATION
To install, press molding into the outer panel flange and engage the pawls.
SIIA0202E
Page 3322 of 4179
EI-24
SIDE GUARD MOLDING
SIDE GUARD MOLDINGPFP:76840
Removal and InstallationEIS000N3
REMOVAL
Side guard molding (front/rear)
1. Apply masking tape around outer circumference of side guard molding.
2. Remove double-faced adhesive tapes with (wide) resin spatula. Disengage clips and remove side guard
molding.
INSTALLATION
1. Remove double-faced adhesive tape remaining on vehicle.
2. Clean contact surface of vehicle (to side guard molding), and install side guard molding to vehicle.
CAUTION:
Do not let air between contact surfaces when installing.
To secure contact, do not wash vehicle within 24 hours after installation.
1. Side guard molding (front door) 2. Side guard molding (rear door)
SIIA0204E
Page 3323 of 4179
DOOR OUTSIDE LOWER MOLDING
EI-25
C
D
E
F
G
H
J
K
L
MA
B
EI
DOOR OUTSIDE LOWER MOLDINGPFP:82877
Removal and InstallationEIS000N4
REMOVAL
Door outside molding (front/rear)
1. Remove clips of door outside molding.
2. Remove door outside molding (front/rear).
INSTALLATION
Installation is in the reverse order of removal.
1. Door outside lower molding (front door) 2. Door outside lower molding (rear door)
SIIA0206E
Page 3324 of 4179
EI-26
SIDE SILL PROTECTOR
SIDE SILL PROTECTORPFP:86856
Removal and InstallationEIS000N5
REMOVAL
1. Remove screw and clip of side sill protector.
2. Remove side sill protector.
INSTALLATION
Installation is in the reverse order of removal.
SIIA0207E
Page 3325 of 4179

ROOF RAIL
EI-27
C
D
E
F
G
H
J
K
L
MA
B
EI
ROOF RAILPFP:73820
Removal and Installation (for Hyper Roof Rail)EIS000N6
REMOVAL
1. Remove driving lamp cap (front).
2. Remove driving lamp mounting nuts.
3. Pull driving lamp upward to disconnect clips of driving lamp from roof panel.
4. Disconnect driving lamp harness connector.
5. Remove driving lamp assembly.
6. Remove hyper roof rail caps (front and rear).
7. Remove side rail mounting bolts and nuts, then remove side rail.
8. Remove rear spoiler mounting bolts, then remove rear spoiler.
9. Remove hyper roof rail mounting nuts, then remove hyper roof rail assembly.
10. Remove headlining. Refer to EI-39, "
HEADLINING" .
11. Remove driving lamp bracket, hyper roof rail bracket (front and rear) and roof spoiler bracket.
INSTALLATION
Installation is in the reverse order of removal.
1. Roof rail 2. Rear spoiler 3. Hyper roof rail rear cap
4. Rear spoiler bracket 5. Hyper roof rail center bracket (rear) 6. Hyper roof rail center bracket (front)
7. Hyper roof rail bracket (rear) 8. Hyper roof rail bracket (front) 9. Hyper roof rail front cap
10. Side rail 11. Driving lamp cap (rear) 12. Driving lamp assembly
13. Driving lamp cap (front) 14. Driving lamp bracket
PIIA6946E
Page 3326 of 4179
EI-28
ROOF RAIL
Removal and Installation (for Roof Rail)EIS008OQ
REMOVAL
1. Remove headlining. Refer to EI-35, "BODY SIDE TRIM" .
2. Remove roof rail mounting nuts and roof rail covers (or roof
spoiler) mounting nuts.
3. Remove roof rail bracket mounting nuts (front and rear).
1. Roof rail 2. Front cap 3. Rear cap
4. Roof rail cover 5. Roof rail bracket (front) 6. Roof rail bracket (rear)
SIIA0265E
SIIA0214E
SIIA0215E
Page 3327 of 4179
ROOF RAIL
EI-29
C
D
E
F
G
H
J
K
L
MA
B
EI
4. Remove roof rail covers (or roof spoiler). For removal of roof spoiler,refer to EI-30, "ROOF SPOILER" .
5. Remove roof rail mounting clips, and remove roof rails.
INSTALLATION
Installation is in the reverse order of removal.
Page 3328 of 4179
EI-30
ROOF SPOILER
ROOF SPOILERPFP:96030
Removal and InstallationEIS000N7
REMOVAL
1. Remove headlining. Refer to EI-39, "Removal and Installation" .
2. Remove covers (left and right).
3. Remove roof spoiler mounting nuts (upper and lower roof surfaces).
4. Pull roof spoiler upwards. Remove tabs (1 each on left/right) which are engaged with the roof rails.
Remove roof spoiler.
INSTALLATION
Installation is in the reverse order of removal.
1. Cover (left) 2. Cover (right) 3. Roof spoiler
SIIA0216E