Page 265 of 5598
AV
CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR)
AV-117
< BASIC INSPECTION >
C
D E
F
G H
I
J
K L
M B A
O P
It can be initialized to the NISSAN factory default condition with “Initialize Camera Image Calibration” of
“Calibrating Camera Image”.
The adjustment value is cancelled on this mode by performing “Initialize Camera Image Calibration”.
>> Calibration end
Revision: 2010 May2011 QX56
Page 266 of 5598

AV-118
< DTC/CIRCUIT DIAGNOSIS >
U1000 CAN COMM CIRCUIT
DTC/CIRCUIT DIAGNOSIS
U1000 CAN COMM CIRCUIT
DescriptionINFOID:0000000006216248
CAN (Controller Area Network) is a serial communication line for real-time application. It is an on-vehicle mul-
tiplex communication line with high data communication s peed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independently). In CA N communication, control units are connected with 2
communication lines (CAN-H, CAN-L) allowing a high rate of information transmission with less wiring. Each
control unit transmits/receives data but selectively reads required data only.
CAN Communication Signal Chart. Refer to LAN-28, "
CAN COMMUNICATION SYSTEM : CAN Communica-
tion Signal Chart".
DTC LogicINFOID:0000000006216249
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000006216250
1.PERFORM SELF-DIAGNOSTIC
1. Turn ignition switch ON and wait for 2 seconds or more.
2. Check “Self Diagnostic Result” of “MULTI AV”.
Is
“CAN COMM CIRCUIT” displayed?
YES >> Refer to LAN-18, "Trouble Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
DTCDisplay contents of CON-
SULT-III DTC detection condition Probable malfunction location
U1000 CAN COMM CIRCUIT
[U1000] AV control unit is not transmitting or receiving
CAN communication signal for 2 seconds or
more.
CAN communication system.
Revision: 2010 May2011 QX56
Page 267 of 5598
AV
U1010 CONTROL UNIT (CAN)AV-119
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
J
K L
M B A
O P
U1010 CONTROL UNIT (CAN)
DTC LogicINFOID:0000000006216251
DTC DETECTION LOGIC
DTC Display contents of CON-
SULT-III DTC detection condition Probable malfunction factor
U1010 CONTROL UNIT (CAN)
[U1010] CAN initial diagnosis malfunction is detected. Replace the AV control unit if the malfunction
occurs constantly.
Refer to
AV- 2 1 2 , "
Removal and Installation".
Revision: 2010 May2011 QX56
Page 268 of 5598
AV-120
< DTC/CIRCUIT DIAGNOSIS >
U1200 AV CONTROL UNIT
U1200 AV CONTROL UNIT
DTC LogicINFOID:0000000006216252
DTCDisplay contents of
CONSULT-III DTC detection condition Possible malfunction factor
U1200 Cont Unit
[U1200]
AV control unit malfunction is detected. Replace the AV control unit if the mal-
function occurs constantly.
Refer to
AV- 2 1 2 , "
Removal and In-
stallation".
Revision: 2010 May2011 QX56
Page 269 of 5598
AV
U1201 AV CONTROL UNITAV-121
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
J
K L
M B A
O P
U1201 AV CONTROL UNIT
DTC LogicINFOID:0000000006216253
DTC Display contents of
CONSULT-III DTC detection condition Possible malfunction factor
U1201 GYRO NO CONN
[U1201]
AV control unit malfunction is detected. Replace the AV control unit if the mal-
function occurs constantly.
Refer to
AV- 2 1 2 , "
Removal and In-
stallation".
Revision: 2010 May2011 QX56
Page 270 of 5598
AV-122
< DTC/CIRCUIT DIAGNOSIS >
U1202 AV CONTROL UNIT
U1202 AV CONTROL UNIT
DTC LogicINFOID:0000000006216254
DTCDisplay contents of
CONSULT-III DTC detection condition Possible malfunction factor
U1202 G-SENSOR NO CONN
[U1202]
AV control unit malfunction is detected. Replace the AV control unit if the mal-
function occurs constantly.
Refer to
AV- 2 1 2 , "
Removal and In-
stallation".
Revision: 2010 May2011 QX56
Page 271 of 5598

AV
U1204 AV CONTROL UNITAV-123
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
J
K L
M B A
O P
U1204 AV CONTROL UNIT
DescriptionINFOID:0000000006216255
An intermittent error caused by strong radio interfer ence may be detected unless any symptoms (GPS recep-
tion error, etc.) occur. Replace the AV control uni t if the malfunction occurs constantly. Refer to AV-212,
"Removal and Installation".
DTC LogicINFOID:0000000006216256
Diagnosis ProcedureINFOID:0000000006216257
1.PERFORM THE SELF-DIAGNOSIS
1. Delete the self-diagnosis results. Turn ignition switch OFF.
2. Turn ignition switch ON. Perform the self-diagnosis again.
3. Check that the DTC is detected again.
Is any DTC detected?
YES >> Replace AV control unit. Refer to AV-212, "Removal and Installation".
NO >> An intermittent error caused by strong radi o interference may be detected unless any symptom
(GPS reception error, etc.) occurs.
DTC Display contents of
CONSULT-III DTC detection condition Possible malfunction factor
U1204 GPS CONN
[U1204] GPS malfunction is detected. An intermittent erro
r caused by strong
radio interference may be detected
unless any symptom (GPS reception
error, etc.) occurs.
Replace the AV control unit if the mal-
function occurs constantly.
Refer to AV- 2 1 2 , "
Removal and In-
stallation".
Revision: 2010 May2011 QX56
Page 272 of 5598

AV-124
< DTC/CIRCUIT DIAGNOSIS >
U1205 AV CONTROL UNIT
U1205 AV CONTROL UNIT
DescriptionINFOID:0000000006216258
An intermittent error caused by strong radio interference may be detected unless any symptoms (GPS recep-
tion error, etc.) occur. Replace the AV control uni t if the malfunction occurs constantly. Refer to AV-212,
"Removal and Installation".
DTC LogicINFOID:0000000006216259
Diagnosis ProcedureINFOID:0000000006216260
1.PERFORM THE SELF-DIAGNOSIS
1. Delete the self-diagnosis results. Turn ignition switch OFF.
2. Turn ignition switch ON. Perform the self-diagnosis again.
3. Check that the DTC is detected again.
Is any DTC detected?
YES >> Replace AV control unit. Refer to AV-212, "Removal and Installation".
NO >> An intermittent error caused by strong radi o interference may be detected unless any symptom
(GPS reception error, etc.) occurs.
DTC Display contents of
CONSULT-III DTC detection condition Possible malfunction factor
U1205 GPS ROM
[U1205] GPS malfunction is detected. An intermittent erro
r caused by strong
radio interference may be detected
unless any symptom (GPS reception
error, etc.) occurs.
Replace the AV control unit if the mal-
function occurs constantly.
Refer to AV- 2 1 2 , "
Removal and In-
stallation".
Revision: 2010 May2011 QX56