2011 INFINITI QX56 Factory Service Manual

open hood odometer turn signal power steering interior lights turn signal bulb

Load previous 8 pages

Page 665 of 5598

INFINITI QX56 2011 Factory Service Manual
BRC-148
< PRECAUTION >[INTELLIGENT BRAKE ASSIST]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precautions for IBA System ServiceINFOID:0000000006228296
CAUTION:
Never look straight into the laser beam
disch

Page 666 of 5598

INFINITI QX56 2011 Factory Service Manual
COMPONENT PARTSBRC-149
< SYSTEM DESCRIPTION > [INTELLIGENT BRAKE ASSIST]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts LocationINFOID:0000000006248458
1. ICC st

Page 667 of 5598

INFINITI QX56 2011 Factory Service Manual
BRC-150
< SYSTEM DESCRIPTION >[INTELLIGENT BRAKE ASSIST]
COMPONENT PARTS
Component Description
INFOID:0000000006248459
× : Applicable
13. Steering angle sensor
Refer to BRC-10, "
Component Parts
L

BRC-150
< SYSTEM DESCRIPTION >[INTELLIGENT BRAKE ASSIST]
COMPONENT PARTS
Component Description
INFOID:0000000006248459
× : Applicable
13. Steering angle sensor
Refer to BRC-10, "
Component Parts
Location"
14. ADAS control unit
Refer to DAS-13, "
Component Parts
Location"
A. Back side of engine room (RH) B. Front bumper (center) C. Upper side of brake pedal
D. Under side of inst rument lower driver
panel
Component Function
Description
Vehicle-to-vehicle distance control mode
Conventional (fixed speed) cruise control mode Intelligent Brake Assist (IBA)
Brake Assist (with preview function)
ADAS control unit ×××× ADAS control unit calculates a target distance between vehicles
and a target speed, based on signals received from each sensor
and switch to transmit an engine torque command value to ECM
and a brake fluid pres sure control signal to ABS actuator and
electric unit (control unit) via CAN communication
ADAS control unit transmits buzzer output signal to combination
meter via CAN communication
ICC sensor ×××× ICC sensor detects light reflected from a vehicle ahead by irra-
diating laser forward and calculates a distance from the vehicle
ahead and a relative speed, based on the detected signal
ICC sensor transmits the presence/absence of vehicle ahead and the distance from the vehicle to ADAS control unit via ITS
communication
ECM ×××× ECM transmits the accelerator pedal position signal, ICC brake
switch signal, stop lamp switch signal, ICC steering switch sig-
nal, etc. to ADAS control unit via CAN communication
ECM controls the electric throttle control actuator based on the engine torque demand received from the ADAS control unit via
CAN communication
ABS actuator and electric unit
(control unit) ×××× ABS actuator and electric unit (control unit) transmits the vehicle
speed signal (wheel speed), stop lamp signal and VDC/TCS/
ABS system operation condition to ADAS control unit via CAN
communication
ABS actuator and electric unit (control unit) controls the brake, based on a brake fluid pressure control signal received from the
ADAS control unit via CAN communication
BCM ×BCM transmits the front wiper request signal to ADAS control unit
via CAN communication
TCM ××TCM transmits the signal related to A/T control to ADAS control
unit via CAN communication
Revision: 2010 May2011 QX56

Page 668 of 5598

INFINITI QX56 2011 Factory Service Manual
COMPONENT PARTSBRC-151
< SYSTEM DESCRIPTION > [INTELLIGENT BRAKE ASSIST]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
NOTE:
Only IBA system uses
Combination meter ××××Performs the following operations using

COMPONENT PARTSBRC-151
< SYSTEM DESCRIPTION > [INTELLIGENT BRAKE ASSIST]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
NOTE:
Only IBA system uses
Combination meter ××××Performs the following operations using the signals received from
the ADAS control unit via the CAN communication
Displays the ICC system operation status using the meter dis-
play signal
Illuminates the ICC system warning lamp using the ICC warning
lamp signal
Illuminates the IBA OFF indicator lamp using the IBA OFF indi- cator lamp signal
Operates the buzzer (ICC warning chime) using the buzzer out- put signal
ICC steering switch ×× ICC steering switch allows the ON/OFF of the Intelligent Cruise
Control and the settings of a vehicle speed and distance be-
tween vehicles
ICC steering switch signal is transmitted to ECM. ECM transmits the signal to the ADAS control unit via CAN communication
ICC brake switch ×××× ICC brake switch is turned OFF and stop lamp switch is turned
ON, when depressing the brake pedal
ICC brake switch signal is input to ECM. These signals are transmitted from ECM to ADAS control unit via CAN communi-
cation
Stop lamp switch signal is in put to ECM and ABS actuator and
electric unit (control unit). These signals are transmitted from
ECM and ABS actuator and electric unit (control unit) to ADAS
control unit via CAN communication
Stop lamp switch
××××
ICC brake hold relay ××ICC brake hold relay activates the stop lamp by ICC brake hold re-
lay drive signal (stop lamp drive signal) outputted by the ADAS
control unit
Transfer control unit ××××Transfer control unit transmits a mode selection state of 4WD shift
switch to the ADAS control unit via CAN communication
IBA OFF switch ×
NoteIBA OFF switch signal is input to the ADAS control unit
Steering angle sensor ×Measures the rotation amount, rotation speed, and rotation direc-
tion of steering wheel, and then transmits them to ADAS control
unit via CAN communication
Component
Function
Description
Vehicle-to-vehicle distance control mode
Conventional (fixed speed) cruise control mode Intelligent Brake Assist (IBA)
Brake Assist (with preview function)
Revision: 2010 May2011 QX56

Page 669 of 5598

INFINITI QX56 2011 Factory Service Manual
BRC-152
< SYSTEM DESCRIPTION >[INTELLIGENT BRAKE ASSIST]
SYSTEM
SYSTEM
INTELLIGENT BRAKE ASSIST
INTELLIGENT BRAKE ASSIST : System DescriptionINFOID:0000000006228299
FUNCTION DESCRIPTION
Intelligent B

BRC-152
< SYSTEM DESCRIPTION >[INTELLIGENT BRAKE ASSIST]
SYSTEM
SYSTEM
INTELLIGENT BRAKE ASSIST
INTELLIGENT BRAKE ASSIST : System DescriptionINFOID:0000000006228299
FUNCTION DESCRIPTION
Intelligent Brake Assist (IBA) syst
em warns the driver by a vehicle ahead detection indicator and chime when
there is a risk of a collision with the vehicle ahead in the traveling lane and the driver must take avoidance
action immediately. The system helps reduce the rear -end collision speed by applying the brakes when it
judges a collision can not be avoided.
CAUTION:
The IBA system is a not collision avoidance system. It is the driver ′s responsibility to stay alert, drive
safely and be in control of the vehicle at all times. As there is a performance limit, it may not provide a
warning or brake in certain conditions.
NOTE:
The IBA system shares component parts and diagnosis wi th the Intelligent Cruise Control (ICC) system.
New parts added to the IBA system is the IBA OFF indica tor lamp in the combination meter and the IBA OFF
switch on the instrument driver lower panel.
The ICC sensor integrated unit shares the parts with the ICC, but the IBA system will operate even when the
ICC system is turned to OFF.
OPERATION DESCRIPTION
The IBA system uses an ICC sensor located below t he front bumper to measure the distance to a vehicle
ahead. When the system judges that the distance gets shorter, the vehicle ahead detection indicator on the
combination meter blinks and the warning chime sounds.
To turn the system OFF/ON, push and hold the IBA OFF switch after starting the engine for more than 1 sec-
ond.
NOTE:
The system ON/OFF condition will be memorized even if the ignition switch turns OFF.
The IBA system operates under the following conditions.
- The IBA system will function when the vehicle is driv en at speeds of approximately 15 km/h (10 MPH) and
above, and when the vehicle ′s speed is approximately 15 km/h (10 MPH) faster than that of the vehicle
ahead.
Switch and Indicators
Temporary unavailable indication
1. IBA OFF switch 2. Vehicle ahead detection indicator 3. IBA OFF indicator lamp
A. Under side of Instrument lower panel
(LH) B. On the combination meter
JSFIA0445ZZ
Revision: 2010 May2011 QX56

Page 670 of 5598

INFINITI QX56 2011 Factory Service Manual
SYSTEM
BRC-153
< SYSTEM DESCRIPTION > [INTELLIGENT BRAKE ASSIST]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
Fail-safe Indication
NOTE:
When the IBA turns OFF, the IBA OFF indicator lamp will illuminate.
Condi

Page 671 of 5598

INFINITI QX56 2011 Factory Service Manual
BRC-154
< DTC/CIRCUIT DIAGNOSIS >[INTELLIGENT BRAKE ASSIST]
INTELLIGENT BRAKE ASSIST
DTC/CIRCUIT DIAGNOSIS
INTELLIGENT BRAKE ASSIST
Diagnosis ProcedureINFOID:0000000006228300
1.INTELLIGENT BRAKE ASSI

Page 672 of 5598

INFINITI QX56 2011 Factory Service Manual
SWITCH DOES NOT TURN ON / SWITCH DOES NOT TURN OFF
BRC-155
< SYMPTOM DIAGNOSIS > [INTELLIGENT BRAKE ASSIST]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
SYMPTOM DIAGNOSIS
SWITCH DOES NOT TURN ON / SWITCH DOES

SWITCH DOES NOT TURN ON / SWITCH DOES NOT TURN OFF
BRC-155
< SYMPTOM DIAGNOSIS > [INTELLIGENT BRAKE ASSIST]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
SYMPTOM DIAGNOSIS
SWITCH DOES NOT TURN ON / SWITCH DOES NOT TURN OFF
Symptom TableINFOID:0000000006228301
CAUTION:
Perform the self-diagnosis with CONS ULT-III before the symptom diagnosis. Perform the trouble diag-
nosis if any DTC is detected.
DescriptionINFOID:0000000006228302
IBA system does not turn ON/OFF.
IBA OFF indicator lamp does not illuminate even if the IBA OFF switch is depressed when IBA OFF indicator
lamp is not illuminated.
IBA OFF indicator lamp does not turn off even if t he IBA OFF switch is depressed when IBA OFF indicator
lamp is illuminated.
NOTE:
To turn the system OFF ⇔ON, push and hold the IBA OFF switch after starting the engine for more than 1
second.
The system ON/OFF condition will be memoriz ed even if the ignition switch turns OFF.
Diagnosis ProcedureINFOID:0000000006228303
1.PERFORM THE SELF-DIAGNOSIS
1. Perform “All DTC Reading” with CONSULT-III.
2. Check if the DTC is detected in self-diagnosis results for “ICC/ADAS” with CONSULT-III. Refer to CCS-50,
"DTC Index".
Is any DTC detected?
YES >> GO TO 6.
NO >> GO TO 2.
2.IBA OFF SWITCH INSPECTION
1. Start the engine.
2. Check that “IBA SW” operates normally in “D ATA MONITOR” for “ICC/ADAS” with CONSULT-III.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 5.
3.CHECK IBA OFF INDICATOR CIRCUIT
1. Start the engine.
2. Select the active test item “METE R LAMP” for “ICC/ADAS” with CONSULT-III.
3. Check if the IBA OFF indicator lamp illuminates when the test item is operated.
Is the inspection result normal?
YES >> Refer to CCS-69, "Work Flow".
NO >> GO TO 4.
4.CHECK DATA MONITOR OF COMBINATION METER
Check that “BA W/L” operates normally in “DATA MO NITOR” for “METER/M&A” with CONSULT-III, when the
IBA OFF switch is pushed and hold for more than 1 second.
Is the inspection result normal?
YES >> Replace the combination meter. Refer to MWI-85, "Removal and Installation".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
Symptom Inspection item/Reference page
IBA system does not turn ON/OFF IBA OFF indicator lamp is not turned
ON
⇔OFF when operating IBA OFF switch BRC-155, "
Diagnosis Procedure"
Revision: 2010 May2011 QX56

Load next 8 pages

Page: < prev 1-10 ... 633-640 641-648 649-656 657-664 665-672 673-680 681-688 689-696 697-704 ... 5600 next >

fuel type air filter AUX catalytic converter headlight aiming phone