Page 889 of 5598
![INFINITI QX56 2011 Factory Service Manual
CCS-154
< DTC/CIRCUIT DIAGNOSIS >[ICC]
U1514 STRG SEN CAN 3
U1514 STRG SEN CAN 3
DTC LogicINFOID:0000000006224430
DTC DETECTION LOGIC
NOTE:
If DTC “U1514” is detected along with DTC “U1000”, INFINITI QX56 2011 Factory Service Manual
CCS-154
< DTC/CIRCUIT DIAGNOSIS >[ICC]
U1514 STRG SEN CAN 3
U1514 STRG SEN CAN 3
DTC LogicINFOID:0000000006224430
DTC DETECTION LOGIC
NOTE:
If DTC “U1514” is detected along with DTC “U1000”,](/manual-img/42/57033/w960_57033-888.png)
CCS-154
< DTC/CIRCUIT DIAGNOSIS >[ICC]
U1514 STRG SEN CAN 3
U1514 STRG SEN CAN 3
DTC LogicINFOID:0000000006224430
DTC DETECTION LOGIC
NOTE:
If DTC “U1514” is detected along with DTC “U1000”, first diagnose the DTC “U1000”. Refer to
CCS-145,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the MAIN switch of ICC system ON.
3. Perform “All DTC Reading” with CONSULT-III.
4. Check if the “U1514” is detected as the current ma lfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1514” detected as the current malfunction?
YES >> Refer to CCS-154, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006224431
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected ot her than “U1514” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communication system inspecti on. Repair or replace the malfunctioning parts.
Refer to CCS-145, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
BRC-51, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board dis-
play) Trouble diagnosis name DTC detecting condition Possible causes
U1514 (165) STRG SEN CAN CIRC 3 ADAS control unit detects an error signal that is
received from steering angle sensor via CAN
communication
Steering angle sensor
Revision: 2010 May2011 QX56
Page 890 of 5598
![INFINITI QX56 2011 Factory Service Manual
CCS
U1515 ICC SENSOR CAN 3CCS-155
< DTC/CIRCUIT DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
U1515 ICC SENSOR CAN 3
DTC LogicINFOID:0000000006224432
DTC DETECTION LOGIC
NOTE:
If DTC “U1515” is INFINITI QX56 2011 Factory Service Manual
CCS
U1515 ICC SENSOR CAN 3CCS-155
< DTC/CIRCUIT DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
U1515 ICC SENSOR CAN 3
DTC LogicINFOID:0000000006224432
DTC DETECTION LOGIC
NOTE:
If DTC “U1515” is](/manual-img/42/57033/w960_57033-889.png)
CCS
U1515 ICC SENSOR CAN 3CCS-155
< DTC/CIRCUIT DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
U1515 ICC SENSOR CAN 3
DTC LogicINFOID:0000000006224432
DTC DETECTION LOGIC
NOTE:
If DTC “U1515” is detected along with DTC “U 1000”, first diagnose the DTC “U1000”. Refer to CCS-145,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the MAIN switch of ICC system ON.
3. Perform “All DTC Readi ng” with CONSULT-III.
4. Check if the “U1515” is detected as the current ma lfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1515” detected as the current malfunction?
YES >> Refer to CCS-155, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006224433
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “U1515” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communicati on system inspection. Repair or replace the malfunctioning parts.
Refer to CCS-145, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK ICC SENSOR SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “LASER”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
CCS-55, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board dis-
play) Trouble diagnosis name DTC detecting condition Possible causes
U1515 (165) ICC SENSOR CAN
CIRC 3 ADAS control unit detects an error signal that is
received from ICC sensor via CAN communi-
cation
ICC sensor
Revision: 2010 May2011 QX56
Page 891 of 5598
![INFINITI QX56 2011 Factory Service Manual
CCS-156
< DTC/CIRCUIT DIAGNOSIS >[ICC]
U1517 ACCELERATOR PEDAL ACTUATOR CAN 3
U1517 ACCELERATOR PEDAL ACTUATOR CAN 3
DTC LogicINFOID:0000000006224434
DTC DETECTION LOGIC
NOTE:
If DTC “U1517” is d INFINITI QX56 2011 Factory Service Manual
CCS-156
< DTC/CIRCUIT DIAGNOSIS >[ICC]
U1517 ACCELERATOR PEDAL ACTUATOR CAN 3
U1517 ACCELERATOR PEDAL ACTUATOR CAN 3
DTC LogicINFOID:0000000006224434
DTC DETECTION LOGIC
NOTE:
If DTC “U1517” is d](/manual-img/42/57033/w960_57033-890.png)
CCS-156
< DTC/CIRCUIT DIAGNOSIS >[ICC]
U1517 ACCELERATOR PEDAL ACTUATOR CAN 3
U1517 ACCELERATOR PEDAL ACTUATOR CAN 3
DTC LogicINFOID:0000000006224434
DTC DETECTION LOGIC
NOTE:
If DTC “U1517” is detected along with DTC “U1000”, first diagnose the DTC “U1000”. Refer to
CCS-145,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the MAIN switch of ICC system ON.
3. Perform “All DTC Reading” with CONSULT-III.
4. Check if the “U1517” is detected as the current ma lfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1517” detected as the current malfunction?
YES >> Refer to CCS-156, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006224435
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected ot her than “U1517” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communication system inspecti on. Repair or replace the malfunctioning parts.
Refer to CCS-145, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK ACCELERATOR PEDAL ACTUAT OR SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “ACCELE PEDAL ACT”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
DAS-108, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board dis-
play) Trouble diagnosis name DTC detecting condition Possible causes
U1517 (167) APA CAN CIRC 3 ADAS control unit detects an error signal that is
received from accelerator pedal actuator via
CAN communication
Accelerator pedal actuator
Revision: 2010 May2011 QX56
Page 892 of 5598
![INFINITI QX56 2011 Factory Service Manual
CCS
U1520 4WD CAN 3CCS-157
< DTC/CIRCUIT DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
U1520 4WD CAN 3
DTC LogicINFOID:0000000006224436
DTC DETECTION LOGIC
NOTE:
If DTC “U1520” is detected alon INFINITI QX56 2011 Factory Service Manual
CCS
U1520 4WD CAN 3CCS-157
< DTC/CIRCUIT DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
U1520 4WD CAN 3
DTC LogicINFOID:0000000006224436
DTC DETECTION LOGIC
NOTE:
If DTC “U1520” is detected alon](/manual-img/42/57033/w960_57033-891.png)
CCS
U1520 4WD CAN 3CCS-157
< DTC/CIRCUIT DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
U1520 4WD CAN 3
DTC LogicINFOID:0000000006224436
DTC DETECTION LOGIC
NOTE:
If DTC “U1520” is detected along with DTC “U 1000”, first diagnose the DTC “U1000”. Refer to CCS-145,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the MAIN switch of ICC system ON.
3. Perform “All DTC Readi ng” with CONSULT-III.
4. Check if the “U1520” is detected as the current ma lfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1520” detected as the current malfunction?
YES >> Refer to CCS-157, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006224437
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “U1520” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communicati on system inspection. Repair or replace the malfunctioning parts.
Refer to CCS-145, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK TRANSFER CONTROL UNIT SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “ALL MODE AWD/4WD”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
DLN-29, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board dis-
play) Trouble diagnosis name DTC detecting condition Possible causes
U1520 (176) 4WD CAN CIRC 3 ADAS control unit detects an error signal that is
received from transfer control unit via CAN
communication
Transfer control unit
Revision: 2010 May2011 QX56
Page 893 of 5598
![INFINITI QX56 2011 Factory Service Manual
CCS-158
< DTC/CIRCUIT DIAGNOSIS >[ICC]
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
ADAS CONTROL UNIT
ADAS CONTROL UNIT : Diagnosis ProcedureINFOID:0000000006228002
1.CHECK ADAS CO INFINITI QX56 2011 Factory Service Manual
CCS-158
< DTC/CIRCUIT DIAGNOSIS >[ICC]
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
ADAS CONTROL UNIT
ADAS CONTROL UNIT : Diagnosis ProcedureINFOID:0000000006228002
1.CHECK ADAS CO](/manual-img/42/57033/w960_57033-892.png)
CCS-158
< DTC/CIRCUIT DIAGNOSIS >[ICC]
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
ADAS CONTROL UNIT
ADAS CONTROL UNIT : Diagnosis ProcedureINFOID:0000000006228002
1.CHECK ADAS CONTROL UNIT POWER SUPPLY CIRCUIT
Check voltage between ADAS control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair the ADAS control unit power supply circuit.
2.CHECK ADAS CONTROL UNIT GROUND CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect the ADAS control unit connector.
3. Check for continuity between ADAS control unit harness connector and ground.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair the ADAS control unit ground circuit.
ICC SENSOR
ICC SENSOR : Diagnosis ProcedureINFOID:0000000006224439
1.CHECK ICC SENSOR POWER SUPPLY CIRCUIT
Check voltage between ICC sensor harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair the ICC sensor power supply circuit.
2.CHECK ICC SENSOR GROUND CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect the ICC sensor connector.
Te r m i n a l Condition
Voltag e
(Approx.)
(+) (–)
ADAS control unit
GroundIgnition
switch
Connector Terminal
B61 16 OFF 0 V
ON Battery volt-
age
ADAS control unit
GroundContinuity
Connector Terminal
B61 6 Existed
Te r m i n a l Condition
Voltag e
(Approx.)
(+) (–)
ICC sensor
GroundIgnition
switch
Connector Terminal
E65 1 OFF 0 V
ON Battery volt-
age
Revision: 2010 May2011 QX56
Page 894 of 5598
CCS
POWER SUPPLY AND GROUND CIRCUITCCS-159
< DTC/CIRCUIT DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
3. Check for continuity between I CC sensor harness connector and ground.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair the ICC sensor ground circuit.
ICC sensor GroundContinuity
Connector Terminal
E65 4 Existed
Revision: 2010 May2011 QX56
Page 895 of 5598
![INFINITI QX56 2011 Factory Service Manual
CCS-160
< SYMPTOM DIAGNOSIS >[ICC]
INTELLIGENT CRUISE CONT
ROL SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
INTELLIGENT CRUISE CONTROL SYSTEM SYMPTOMS
Symptom TableINFOID:0000000006224440
Symptoms Reference pag INFINITI QX56 2011 Factory Service Manual
CCS-160
< SYMPTOM DIAGNOSIS >[ICC]
INTELLIGENT CRUISE CONT
ROL SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
INTELLIGENT CRUISE CONTROL SYSTEM SYMPTOMS
Symptom TableINFOID:0000000006224440
Symptoms Reference pag](/manual-img/42/57033/w960_57033-894.png)
CCS-160
< SYMPTOM DIAGNOSIS >[ICC]
INTELLIGENT CRUISE CONT
ROL SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
INTELLIGENT CRUISE CONTROL SYSTEM SYMPTOMS
Symptom TableINFOID:0000000006224440
Symptoms Reference page
Operation MAIN switch does not turn ON
Refer to CCS-161, "
Description"MAIN switch does not turn OFF
ICC system cannot be set (MAIN switch turns
ON/OFF) Refer to
CCS-162, "
Description"
CANCEL switch does not function
Refer to CCS-164, "
Description"
Resume does not function
Set speed does not increase
Set distance to a vehicle ahead cannot be
changed
ICC is not canceled when the A/T selector lever
is “N” position Refer to
CCS-165, "
Description"
Display/Chime ICC system display not appear Refer to
MWI-29, "On Board Diagnosis Function"
Chime does not sound Refer to CCS-166, "Description"
Control Driving force is hunting Refer to CCS-168, "Description"
Function to detect
a vehicle aheadSystem frequently cannot detect a vehicle ahead
Refer to CCS-169, "
Description"Distance to detect a vehicle ahead is short
System misidentifies a vehicle even though there
is no vehicle ahead Adjust laser beam aiming: Refer to
CCS-72, "
Descrip-
tion"
Perform ICC system action test. Refer to CCS-77, "
De-
scription"System misidentifies a vehicle in the next lane
System does not detect a vehicle at all Refer to CCS-171, "
Description"
Revision: 2010 May2011 QX56
Page 896 of 5598
![INFINITI QX56 2011 Factory Service Manual
CCS
MAIN SWITCH DOES NOT TURN ON, MAIN SWITCH DOES NOT TURN OFF
CCS-161
< SYMPTOM DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
MAIN SWITCH DOES NOT TURN ON, MAIN SWITCH DOES NOT TURN
OFF
Descripti INFINITI QX56 2011 Factory Service Manual
CCS
MAIN SWITCH DOES NOT TURN ON, MAIN SWITCH DOES NOT TURN OFF
CCS-161
< SYMPTOM DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
MAIN SWITCH DOES NOT TURN ON, MAIN SWITCH DOES NOT TURN
OFF
Descripti](/manual-img/42/57033/w960_57033-895.png)
CCS
MAIN SWITCH DOES NOT TURN ON, MAIN SWITCH DOES NOT TURN OFF
CCS-161
< SYMPTOM DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
MAIN SWITCH DOES NOT TURN ON, MAIN SWITCH DOES NOT TURN
OFF
DescriptionINFOID:0000000006224441
MAIN switch does not turn ON
ICC system display does not appear ev en when MAIN switch is pressed.
MAIN switch does not turn OFF When ICC system display is ON, display does not turn OFF even if MAIN switch is pressed.
NOTE:
When ICC system warning lamp illuminates, perform t he self-diagnosis of ICC system, and then repair or
replace the malfunctioning parts.
Diagnosis ProcedureINFOID:0000000006224442
1.MAIN SWITCH INSPECTION
1. Start the engine.
2. Check that “MAIN SW” and “CRUISE LAMP” operate no rmally in “DATA MONITOR” of “ICC/ADAS” with
CONSULT-III.
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 4.
2.CHECK COMBINATION METER
Check that “CRUISE IND” operates normally in “DATA MONITOR” of “METER/M&A”.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 4.
3.PERFORM SELF-DIAGNOSIS OF COMBINATION METER
1. Perform “Self Diagnostic Re sult” of “METER/M&A”.
2. Check if DTC is detected. Refer to MWI-43, "
DTC Index".
Is any DTC detected?
YES >> Repair or replace malfunctioning parts.
NO >> GO TO 4.
4.PERFORM SELF-DIAGNOSIS RESULTS OF ICC SYSTEM
1. Perform “All DTC Reading”.
2. Check if the “U1000” is detected in self-diagnosis results of “ICC/ADAS”.
Is
“U1000” detected?
YES >> GO TO 5.
NO >> GO TO 6.
5.CAN COMMUNICATIONS INSPECTION
Check the CAN communication and repair or replace malfunctioning parts. Refer to CCS-145, "
ADAS CON-
TROL UNIT : DTC Logic".
>> INSPECTION END
6.CHECK ICC STEERING SWITCH
Check the ICC steering switch. Refer to CCS-177, "
Exploded View".
>> INSPECTION END
Revision: 2010 May2011 QX56