Page 297 of 5598

AV
U1264 ANTENNA AMP.AV-149
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
J
K L
M B A
O P
U1264 ANTENNA AMP.
DTC LogicINFOID:0000000006216301
Diagnosis ProcedureINFOID:0000000006216302
1.CHECK CONTINUITY BETWEEN AV CONTROL UNIT AND ANTENNA AMP.
1. Turn ignition switch OFF.
2. Disconnect antenna amp. connector and AV control unit connector.
3. Check continuity between AV control unit harness connector and antenna amp. harness connector.
4. Check continuity between AV control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK VOLTAGE AV CONTROL UNIT
1. Connect AV control unit connector.
2. Turn ignition switch ON.
3. Check voltage between AV control unit harness connector and ground.
Is the inspection result normal?
YES >> Replace antenna amp. Refer to AV-224, "Removal and Installation".
NO >> Replace AV control unit. Refer to AV-212, "
Removal and Installation".
DTCDisplay contents of
CONSULT-III DTC detection condition Possible malfunction factor
U1264 ANTENNA AMP TER-
MINAL
[U1264] Radio antenna amp. ON circuit is open or shorted.
Check antenna amp. ON signal circuit
between the AV control unit and radio
antenna amp.
AV control unit Antenna amp.
Continuity
Connector Terminals Connector Terminals
M319 152 M313 1 Existed
AV control unit GroundContinuity
Connector Terminals
M319 152 Not existed
(+) (–)Vol tag e
(Approx.)
AV c o n t r o l u n i t
Connector Terminals M319 152 Ground 12.0 V
Revision: 2010 May2011 QX56
Page 298 of 5598

AV-150
< DTC/CIRCUIT DIAGNOSIS >
U1265 BOSE AMP.
U1265 BOSE AMP.
DTC LogicINFOID:0000000006216303
Diagnosis ProcedureINFOID:0000000006216304
1.CHECK CONTINUITY BETWEEN AV CONTROL UNIT AND BOSE AMP.
1. Turn ignition switch OFF.
2. Disconnect BOSE amp. connecto r and AV control unit connector.
3. Check continuity between AV control unit harness connector and BOSE amp. harness connector.
4. Check continuity between AV c ontrol unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK VOLTAGE AV CONTROL UNIT
1. Connect AV control unit connector.
2. Turn ignition switch ON.
3. Check voltage between AV control unit harness connector and ground.
Is the inspection result normal?
YES >> Replace BOSE amp. Refer to AV-223, "Removal and Installation".
NO >> Replace AV control unit. Refer to AV-212, "
Removal and Installation".
DTCDisplay contents of
CONSULT-III DTC detection condition Possible malfunction factor
U1265 AMP ON TERMINAL
[U1265] BOSE amp. ON signal circuit is open or shorted. Check BOSE amp. ON signal circuit
between the AV control unit and
BOSE amp.
AV control unit BOSE amp.
Continuity
Connector Terminals Connector Terminals
M208 1 B230 20 Existed
AV c o n t r o l u n i t GroundContinuity
Connector Terminals
M208 1 Not existed
(+) (–)Voltage
(Approx.)
AV c o n t r o l u n i t
Connector Terminals M208 1 Ground 12.0 V
Revision: 2010 May2011 QX56
Page 299 of 5598

AV
U1300 AV COMM CIRCUITAV-151
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
J
K L
M B A
O P
U1300 AV COMM CIRCUIT
DescriptionINFOID:0000000006216305
U1300 is indicated when malfunction occurs in communica tion signal of multi AV system. Indicated simulta-
neously, without fail, with the malfunction of control uni ts connected to AV control unit with communication line.
Determine the possible malfunction cause from the table below.
SELF-DIAGNOSIS RESULTS DISPLAY ITEM
DTC Display contents of
CONSULT-III DTC detection condition Possible malfunction factor
U1300
U1240 AV COMM CIRCUIT
[U1300]
SWITCH CONN [U1240] When either one of the following items are detected:
multifunction switch power supply and ground circuits
are malfunctioning.
AV communication circuits between AV control unit
and multifunction switch are malfunctioning. Multifunction switch power supply
and ground circuits.
AV communication circuits between AV control unit and multifunction
switch.
U1300
U1246 AV COMM CIRCUIT
[U1300]
VIDEO DIST CONN [U1246] When either one of the following items are detected:
video distributor power supply and ground circuits are
malfunctioning.
headrest display unit LH power supply and ground cir- cuits are malfunctioning.
AV communication circuits between AV control unit and headrest display unit LH are malfunctioning.
location recognition signal circuit between headrest
display unit LH and ground is malfunctioning. Video distributor power supply and
ground circuits.
Headrest display unit LH power sup- ply and ground circuits.
AV communication circuits between AV control unit and headrest display
unit LH.
Location recognition signal circuit between headrest display unit LH
and ground.
U1300
U125B AV COMM CIRCUIT
[U1300]
AROUND CAMERA
CONN [U125B] When either one of the following items are detected:
around view monitor control unit power supply and
ground circuits are malfunctioning.
AV communication circuits between AV control unit
and around view monitor control unit are malfunction-
ing. Around view monitor control unit
power supply and ground circuits.
AV communication circuits between AV control unit and around view
monitor control unit.
U1300
U125C AV COMM CIRCUIT
[U1300]
SONAR CONN
[U125C] When either one of the following items are detected:
sonar control unit power supply and ground circuits are
malfunctioning.
AV communication circuits between AV control unit and sonar control unit are malfunctioning. Sonar control unit power supply and
ground circuits.
AV communication circuits between AV control unit and sonar control
unit.
U1300
U1240
U125C U125B AV COMM CIRCUIT
[U1300]
SWITCH CONN [U1240]
SONAR CONN [U125C]
AROUND CAMERA
CONN [U125B]
AV communication circuits between AV control unit and
multifunction switch are malfunctioning. AV communication circuits between AV
control unit and multifunction switch.
U1300
U1240
U125C U125B U1246 AV COMM CIRCUIT
[U1300]
SWITCH CONN
[U1240]
SONAR CONN [U125C]
AROUND CAMERA CONN [U125B]
VIDEO DIST CONN
[U1246]
Revision: 2010 May2011 QX56
Page 300 of 5598
AV-152
< DTC/CIRCUIT DIAGNOSIS >
U1310 AV CONTROL UNIT
U1310 AV CONTROL UNIT
DTC LogicINFOID:0000000006216306
DTCDisplay contents of
CONSULT-III DTC detection condition Possible malfunction factor
U1310 CONTROL UNIT (AV)
[U1310] An initial diagnosis error is detected in AV communication
circuit. Replace the AV control unit if the mal-
function occurs constantly.
Refer to
AV- 2 1 2 , "
Removal and In-
stallation".
Revision: 2010 May2011 QX56
Page 301 of 5598
AV
B2700 CORNER SENSOR [FL]AV-153
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
J
K L
M B A
O P
B2700 CORNER SENSOR [FL]
DTC LogicINFOID:0000000006216307
DTC DETECTION LOGIC
DTC No. CONSULT-III indication DTC detection condition Troubleshooting B2700 CORNER SENSOR [FL]
[B2700]
Corner sensor front LH is malfunctioning. Replace corner sensor front LH.
Revision: 2010 May2011 QX56
Page 302 of 5598
![INFINITI QX56 2011 Factory Service Manual
AV-154
< DTC/CIRCUIT DIAGNOSIS >
B2701 SENSOR HARNESS OPEN [CR-FL]
B2701 SENSOR HARNESS OPEN [CR-FL]
DTC LogicINFOID:0000000006216308
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000006216309
1 INFINITI QX56 2011 Factory Service Manual
AV-154
< DTC/CIRCUIT DIAGNOSIS >
B2701 SENSOR HARNESS OPEN [CR-FL]
B2701 SENSOR HARNESS OPEN [CR-FL]
DTC LogicINFOID:0000000006216308
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000006216309
1](/manual-img/42/57033/w960_57033-301.png)
AV-154
< DTC/CIRCUIT DIAGNOSIS >
B2701 SENSOR HARNESS OPEN [CR-FL]
B2701 SENSOR HARNESS OPEN [CR-FL]
DTC LogicINFOID:0000000006216308
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000006216309
1.CHECK HARNESS CORNER SENSOR FRONT LH SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect sonar control unit connector and corner sensor front LH connector.
3. Check continuity between sonar control unit harnes s connector and corner sensor front LH harness con-
nector.
4. Check continuity between sonar control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK HARNESS CORNER SENSOR FRONT LH GROUND CIRCUIT
Check continuity between sonar control unit harness c onnector and corner sensor front LH harness connector.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair harness or connector.
DTC No. CONSULT-III indication DTC detection condition Troubleshooting B2701 SENSOR HARNESS
OPEN [CR-FL] [B2701]
Corner sensor front LH harness circuit is open. Check corner sensor front LH circuit.
Sonar control unit Corner sensor front LH
Continuity
Connector Terminal Connector Terminal
M47 3 E221 1 Existed
Sonar control unit GroundContinuity
Connector Terminal
M47 3 Not existed
Sonar control unit Corner sensor front LH Continuity
Connector Terminal Connector Terminal
M47 12 E221 2 Existed
Revision: 2010 May2011 QX56
Page 303 of 5598
AV
B2702 CORNER SENSOR [FR]AV-155
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
J
K L
M B A
O P
B2702 CORNER SENSOR [FR]
DTC LogicINFOID:0000000006216310
DTC DETECTION LOGIC
DTC No. CONSULT-III indication DTC detection condition Troubleshooting B2702 CORNER SENSOR [FR]
[B2702]
Corner sensor front RH is malfunctioning. Replace corner sensor front RH.
Revision: 2010 May2011 QX56
Page 304 of 5598
![INFINITI QX56 2011 Factory Service Manual
AV-156
< DTC/CIRCUIT DIAGNOSIS >
B2703 SENSOR HARNESS OPEN [CR-FR]
B2703 SENSOR HARNESS OPEN [CR-FR]
DTC LogicINFOID:0000000006216311
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000006216312
1 INFINITI QX56 2011 Factory Service Manual
AV-156
< DTC/CIRCUIT DIAGNOSIS >
B2703 SENSOR HARNESS OPEN [CR-FR]
B2703 SENSOR HARNESS OPEN [CR-FR]
DTC LogicINFOID:0000000006216311
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000006216312
1](/manual-img/42/57033/w960_57033-303.png)
AV-156
< DTC/CIRCUIT DIAGNOSIS >
B2703 SENSOR HARNESS OPEN [CR-FR]
B2703 SENSOR HARNESS OPEN [CR-FR]
DTC LogicINFOID:0000000006216311
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000006216312
1.CHECK HARNESS CORNER SENSOR FRONT RH SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect sonar control unit connector and corner sensor front RH connector.
3. Check continuity between sonar control unit harne ss connector and corner sensor front RH harness con-
nector.
4. Check continuity between sonar control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK HARNESS CORNER SENSOR FRONT RH GROUND CIRCUIT
Check continuity between sonar control unit harness connector and corner sensor front RH harness connec-
tor.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair harness or connector.
DTC No. CONSULT-III indication DTC detection condition Troubleshooting
B2703 SENSOR HARNESS
OPEN [CR-FR] [B2703]
Corner sensor front RH harness circuit is open. Check corner sensor front RH circuit.
Sonar control unit Corner sensor front RH
Continuity
Connector Terminal Connector Terminal
M47 4 E222 1 Existed
Sonar control unit GroundContinuity
Connector Terminal
M47 4 Not existed
Sonar control unit Corner sensor front RH Continuity
Connector Terminal Connector Terminal
M47 12 E222 2 Existed
Revision: 2010 May2011 QX56