2011 INFINITI QX56 Factory Service Manual

high beam overheating power steering fluid gearbox fog light fuel pump

Load previous 8 pages

Page 2225 of 5598

INFINITI QX56 2011 Factory Service Manual
P0102, P0103 MAF SENSOREC-201
< DTC/CIRCUIT DIAGNOSIS > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
P0102, P0103 MAF SENSOR
DTC LogicINFOID:0000000006217789
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDUR

Page 2226 of 5598

INFINITI QX56 2011 Factory Service Manual
EC-202
< DTC/CIRCUIT DIAGNOSIS >[VK56VD]
P0102, P0103 MAF SENSOR
Air duct
Vacuum hoses
Intake air passage between air duct to intake manifold
Is the inspection result normal?
YES >> GO TO 3.
NO

Page 2227 of 5598

INFINITI QX56 2011 Factory Service Manual
P0102, P0103 MAF SENSOREC-203
< DTC/CIRCUIT DIAGNOSIS > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
YES >> GO TO 8.
NO >> Replace mass air flow sensor. Refer to
EM-27, "
Exploded View".
8.CHECK INTERMI

P0102, P0103 MAF SENSOREC-203
< DTC/CIRCUIT DIAGNOSIS > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
YES >> GO TO 8.
NO >> Replace mass air flow sensor. Refer to
EM-27, "
Exploded View".
8.CHECK INTERMITTENT INCIDENT
Refer to GI-40, "
Intermittent Incident".
>> INSPECTION END
Component Inspection (MAF Sensor)INFOID:0000000006290102
1.CHECK MASS AIR FLOW SENSOR-I
WITH CONSULT-III
1. Turn ignition switch OFF.
2. Reconnect all harness connectors disconnected.
3. Start engine and warm it up to normal operating temperature.
4. Connect CONSULT-III and select “DATA MONITOR” mode.
5. Select “MAS A/F SE-B1” , and check the indication.
*: Check for linear voltage rise in response to engine being increased to about 4,000 rpm.
WITHOUT CONSULT-III
1. Turn ignition switch OFF.
2. Reconnect all harness connectors disconnected.
3. Start engine and warm it up to normal operating temperature.
4. Check the voltage between ECM harness connector terminals under the following conditions.
*: Check for linear voltage rise in response to engine being increased to about 4,000 rpm.
Is the inspection result normal?
YES >> INSPECTION END
NO >> GO TO 2.
2.CHECK FOR THE CAUSE OF UNEVEN AIR FL OW THROUGH MASS AIR FLOW SENSOR
1. Turn ignition switch OFF.
2. Check for the cause of uneven air flow through mass air flow sensor. Refer to the following.
- Crushed air ducts
- Malfunctioning seal of air cleaner element
- Uneven dirt of air cleaner element
- Improper specification of intake air system parts
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 3.
Monitor item Condition Indication (V)
MAS A/F SE-B1 Ignition switch ON (Engine stopped.) Approx. 0.4
Idle (Engine is warmed-up to normal operating temperature.) 0.9 - 1.1
2,500 rpm (Engine is warmed-up to normal operating temperature.) 1.4 - 1.9
Idle to about 4,000 rpm 0.9 - 1.1 to Approx. 2.4*
ECM Condition Voltage (V)
Connector +–
Terminal Terminal
F 111 22
(MAF sensor signal) 25Ignition switch ON (Engine stopped.) Approx. 0.4
Idle (Engine is warmed-up to normal operat-
ing temperature.)
0.9 - 1.1
2,500 rpm (Engine is warmed-up to normal
operating temperature.) 1.4 - 1.9
Idle to about 4,000 rpm 0.9 - 1.1 to Approx. 2.4*
Revision: 2010 May2011 QX56

Page 2228 of 5598

INFINITI QX56 2011 Factory Service Manual
EC-204
< DTC/CIRCUIT DIAGNOSIS >[VK56VD]
P0102, P0103 MAF SENSOR
3.CHECK MASS AIR FLOW SENSOR-II
WITH CONSULT-III
1. Repair or replace malfunctioning part.
2. Start engine and warm it up to normal op

EC-204
< DTC/CIRCUIT DIAGNOSIS >[VK56VD]
P0102, P0103 MAF SENSOR
3.CHECK MASS AIR FLOW SENSOR-II
WITH CONSULT-III
1. Repair or replace malfunctioning part.
2. Start engine and warm it up to normal operating temperature.
3. Connect CONSULT-III and select “DATA MONITOR” mode.
4. Select “MAS A/F SE-B1””, and check the indication.
*: Check for linear voltage rise in response to engine being increased to about 4,000 rpm.
WITHOUT CONSULT-III
1. Repair or replace malfunctioning part.
2. Start engine and warm it up to normal operating temperature.
3. Check the voltage between ECM harness connector terminals under the following conditions.
*: Check for linear voltage rise in response to engine being increased to about 4,000 rpm.
Is the inspection result normal?
YES >> INSPECTION END
NO >> GO TO 4.
4.CHECK MASS AIR FLOW SENSOR-III
WITH CONSULT-III
1. Turn ignition switch OFF.
2. Disconnect mass air flow sensor harness connector and reconnect it again.
3. Start engine and warm it up to normal operating temperature.
4. Connect CONSULT-III and select “DATA MONITOR” mode.
5. Select “MAS A/F SE-B1”, and check the indication.
*: Check for linear voltage rise in response to engine being increased to about 4,000 rpm.
WITHOUT CONSULT-III
1. Turn ignition switch OFF.
2. Disconnect mass air flow sensor harness connector and reconnect it again.
3. Start engine and warm it up to normal operating temperature.
4. Check the voltage between ECM harness connector terminals under the following conditions.
Monitor item Condition Indication (V)
MAS A/F SE-B1 Ignition switch ON (Engine stopped.) Approx. 0.4
Idle (Engine is warmed-up to normal operating temperature.) 0.9 - 1.1
2,500 rpm (Engine is warmed-up to normal operating temperature.) 1.4 - 1.9
Idle to about 4,000 rpm 0.9 - 1.1 to Approx. 2.4*
ECM
Condition Voltage (V)
Connector +–
Te r m i n a l Te r m i n a l
F 111 22
(MAF sensor signal) 25Ignition switch ON (Engine stopped.) Approx. 0.4
Idle (Engine is warmed-up to normal operat-
ing temperature.)
0.9 - 1.1
2,500 rpm (Engine is warmed-up to normal
operating temperature.) 1.4 - 1.9
Idle to about 4,000 rpm 0.9 - 1.1 to Approx. 2.4*
Monitor item Condition Indication (V)
MAS A/F SE-B1 Ignition switch ON (Engine stopped.) Approx. 0.4
Idle (Engine is warmed-up to normal operating temperature.) 0.9 - 1.1
2,500 rpm (Engine is warmed-up to normal operating temperature.) 1.4 - 1.9
Idle to about 4,000 rpm 0.9 - 1.1 to Approx. 2.4*
Revision: 2010 May2011 QX56

Page 2229 of 5598

INFINITI QX56 2011 Factory Service Manual
P0102, P0103 MAF SENSOREC-205
< DTC/CIRCUIT DIAGNOSIS > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
*: Check for linear voltage rise in response to engine being increased to about 4,000 rpm.
Is the insp

Page 2230 of 5598

INFINITI QX56 2011 Factory Service Manual
EC-206
< DTC/CIRCUIT DIAGNOSIS >[VK56VD]
P0106 MANIFOLD ABSOL
UTE PRESSURE SENSOR
P0106 MANIFOLD ABSOLU TE PRESSURE SENSOR
DTC LogicINFOID:0000000006288274
DTC DETECTION LOGIC
NOTE:
If DTC P0106 is d

EC-206
< DTC/CIRCUIT DIAGNOSIS >[VK56VD]
P0106 MANIFOLD ABSOL
UTE PRESSURE SENSOR
P0106 MANIFOLD ABSOLU TE PRESSURE SENSOR
DTC LogicINFOID:0000000006288274
DTC DETECTION LOGIC
NOTE:
If DTC P0106 is displayed with ot her DTC, first perform the trouble diagnosis for other DTC.
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
If engine will not start or stops soon, wait at leas t 10 seconds with engine stopped (Ignition switch ON) instead
of running engine at idle speed.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
WITH CONSULT-III
1. Turn ignition switch ON and select “DATA MONITOR” mode with CONSULT-III.
2. Start engine and warm it up to normal operating temperature.
3. Accelerate the vehicle from 0 to 88 km/h (0 to 55 MPH) under the following conditions: CAUTION:
Always drive at a safe speed.
NOTE:
Accelerate with the accelerator pedal kept constant.
The acceleration at engine speed 2,000 and 3,000 rpm allows easy diagnoses.
4. Check 1st trip DTC. WITHOUT CONSULT-III
1. Start engine and warm it up to normal operating temperature.
2. Drive the vehicle under the following conditions.
3. With selector lever in D position, accelerate the v ehicle from 0 to 88 km/h (0 to 55 MPH) under the follow-
ing conditions:
CAUTION:
Always drive at a safe speed.
NOTE:
Accelerate with the accelerator pedal kept constant.
The acceleration at engine speed 2,000 and 3,000 rpm allows easy diagnoses.
DTC No. Trouble diagnosis name
(Trouble diagnosis content) DTC detecting condition Possible cause
P0106 ABSL PRES SEN/CIRC
[Manifold absolute pressure (MAP)
circuit range/performance] A difference exceeding the specified
value develops between a value
transmitted from the manifold abso-
lute pressure (MAP) sensor to ECM
and an estimated intake pressure of
intake manifold calculated by ECM. Harness or connectors
(The manifold absolute pressure
(MAP) sensor circuit is open or
shorted.)
manifold absolute pressure (MAP)
sensor
Intake air leaks
ACCEL SEN 1 1.4 – 2.0 V
Selector lever D position
Revision: 2010 May2011 QX56

Page 2231 of 5598

INFINITI QX56 2011 Factory Service Manual
P0106 MANIFOLD ABSOLUTE PRESSURE SENSOREC-207
< DTC/CIRCUIT DIAGNOSIS > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to
EC-207, "Diagnosis

Page 2232 of 5598

INFINITI QX56 2011 Factory Service Manual
EC-208
< DTC/CIRCUIT DIAGNOSIS >[VK56VD]
P0106 MANIFOLD ABSOL
UTE PRESSURE SENSOR
2. Also check harness for short to ground and power.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair op

Load next 8 pages

Page: < prev 1-10 ... 2193-2200 2201-2208 2209-2216 2217-2224 2225-2232 2233-2240 2241-2248 2249-2256 2257-2264 ... 5600 next >

oil pressure wiring diagram brake pads steering weight center console