Page 609 of 5598
![INFINITI QX56 2011 Factory Service Manual
BRC-92
< DTC/CIRCUIT DIAGNOSIS >[WITH VDC]
C1130 ENGINE SIGNAL
C1130 ENGINE SIGNAL
DTC LogicINFOID:0000000006222613
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK DTC DETECTION
With CONSULT-I INFINITI QX56 2011 Factory Service Manual
BRC-92
< DTC/CIRCUIT DIAGNOSIS >[WITH VDC]
C1130 ENGINE SIGNAL
C1130 ENGINE SIGNAL
DTC LogicINFOID:0000000006222613
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK DTC DETECTION
With CONSULT-I](/manual-img/42/57033/w960_57033-608.png)
BRC-92
< DTC/CIRCUIT DIAGNOSIS >[WITH VDC]
C1130 ENGINE SIGNAL
C1130 ENGINE SIGNAL
DTC LogicINFOID:0000000006222613
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK DTC DETECTION
With CONSULT-III
1. Turn the ignition switch OFF to ON.
2. Perform self-diagnosis for “ABS”.
Is DTC
“C1130” detected?
YES >> Proceed to diagnosis procedure. Refer to BRC-92, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006222614
1.CHECK ENGINE SYSTEM
With CONSULT-III.
Perform self-diagnosis for “ENGINE”.
Is any DTC detected?
YES >> Check the DTC.
NO >> GO TO 2.
2.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
With CONSULT-III.
1. Erase Self-diagnosis result for “ABS”.
2. Turn the ignition switch OFF.
3. Start the engine and drive the vehicle for a short period of time.
4. Check that the malfunction indicator lamp (MIL) turns OFF.
5. After the vehicle stops, perform self-diagnosis for “ABS”.
Is DTC
“C1130” detected?
YES >> Replace ABS actuator and electr ic unit (control unit). Refer to BRC-137, "Removal and Installa-
tion".
NO >> Check pin terminals and connection of each harness connector for abnormal conditions. Repair or
replace error-detected parts.
DTC Display Item Malfunction detected condition Possible causes
C1130 ENGINE SIGNAL 1 When a malfunction is detected in ECM system. ECM
ABS actuator and electric unit
(control unit)
CAN communication line
Revision: 2010 May2011 QX56
Page 610 of 5598
![INFINITI QX56 2011 Factory Service Manual
C1140 ACTUATOR RELAY SYSTEMBRC-93
< DTC/CIRCUIT DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
C1140 ACTUATOR RELAY SYSTEM
DTC LogicINFOID:0000000006222615
DTC DETECTION LOGIC
DTC CONFIRMAT INFINITI QX56 2011 Factory Service Manual
C1140 ACTUATOR RELAY SYSTEMBRC-93
< DTC/CIRCUIT DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
C1140 ACTUATOR RELAY SYSTEM
DTC LogicINFOID:0000000006222615
DTC DETECTION LOGIC
DTC CONFIRMAT](/manual-img/42/57033/w960_57033-609.png)
C1140 ACTUATOR RELAY SYSTEMBRC-93
< DTC/CIRCUIT DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
C1140 ACTUATOR RELAY SYSTEM
DTC LogicINFOID:0000000006222615
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK DTC DETECTION
With CONSULT-III.
1. Turn the ignition switch OFF to ON.
2. Perform self-diagnosis for “ABS”.
Is DTC
“C1140” detected?
YES >> Proceed to diagnosis procedure. Refer to BRC-93, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006222616
1.CHECK ACTUATOR RELAY POWER SUPPLY
1. Turn the ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) harness connector.
3. Check voltage between ABS actuator and electr ic unit (control unit) harness connector and ground.
4. Turn the ignition switch ON. CAUTION:
Never start engine.
5. Check voltage between ABS actuator and electr ic unit (control unit) harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK ACTUATOR RELAY POWER SUPPLY CIRCUIT
1. Turn the ignition switch OFF.
2. Check 30A fusible link (L).
3. Check continuity and short circuit between ABS act uator and electric unit (control unit) harness connector
terminal (1) and 30A fusible link (L).
Is the inspection result normal?
YES >> Perform trouble diagnosis for battery power supply. Refer to PG-11, "Wiring Diagram - BATTERY
POWER SUPPLY -".
NO >> Repair or replace error-detected parts.
3.CHECK ACTUATOR RELAY GROUND CIRCUIT
DTC Display Item Malfunction detected condition Possible causes
C1140 ACTUATOR RLY When a malfunction is detected in actuator relay. Harness or connector
ABS actuator and electric unit
(control unit)
Fusible link
Battery power supply system
ABS actuator and electric unit (control unit) —Voltage
Connector Terminal
E36 1 Ground Battery voltage
ABS actuator and electric unit (control unit)
—Voltage
Connector Terminal
E36 1 Ground Battery voltage
Revision: 2010 May2011 QX56
Page 611 of 5598
BRC-94
< DTC/CIRCUIT DIAGNOSIS >[WITH VDC]
C1140 ACTUATOR RELAY SYSTEM
1. Turn the ignition switch OFF.
2. Check continuity between ABS actuator and electr
ic unit (control unit) harness connector and the ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace error-detected parts.
4.CHECK TERMINAL
Check ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with harness
connector.
Is the inspection result normal?
YES >> Replace ABS actuator and electr ic unit (control unit). Refer to BRC-137, "Removal and Installa-
tion".
NO >> Repair or replace error-detected parts.
ABS actuator and electric unit (control unit) — Continuity
Connector Terminal
E36 2
Ground Existed
3
E37 48
Revision: 2010 May2011 QX56
Page 612 of 5598
![INFINITI QX56 2011 Factory Service Manual
C1142 PRESS SENSORBRC-95
< DTC/CIRCUIT DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
C1142 PRESS SENSOR
DTC LogicINFOID:0000000006222617
DTC DETECTION LOGIC
*: Models with Advanced Driver INFINITI QX56 2011 Factory Service Manual
C1142 PRESS SENSORBRC-95
< DTC/CIRCUIT DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
C1142 PRESS SENSOR
DTC LogicINFOID:0000000006222617
DTC DETECTION LOGIC
*: Models with Advanced Driver](/manual-img/42/57033/w960_57033-611.png)
C1142 PRESS SENSORBRC-95
< DTC/CIRCUIT DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
C1142 PRESS SENSOR
DTC LogicINFOID:0000000006222617
DTC DETECTION LOGIC
*: Models with Advanced Driver Assistance System
DTC CONFIRMATION PROCEDURE
1.CHECK DTC DETECTION
With CONSULT-III.
1. Turn the ignition switch OFF to ON.
2. Perform self-diagnosis for “ABS”.
Is DTC
“C1142” detected?
YES >> Proceed to diagnosis procedure. Refer to BRC-95, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006222618
1.CHECK STOP LAMP SWITCH SUSTEM
Check stop lamp switch system. Refer to BRC-79, "
Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace error-detected parts.
2.CHECK BRAKE FLUID LEACKAGE
Check brake fluid leakage. Refer to BR-10, "
Inspection".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace error-detected parts.
3.CHECK BRAKE PIPING
Check brake piping. Refer to BR-24, "
FRONT : Inspection" (front), BR-26, "REAR : Inspection" (rear).
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace error-detected parts.
4.CHECK BRAKE PEDAL
Check brake pedal. Refer to BR-21, "
Inspection and Adjustment".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace error-detected parts.
5.CHECK HYDRAULIC BOOSTER ASSEMBLY
Check hydraulic booster assembly. Refer to BR-32, "
Inspection and Adjustment".
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace error-detected parts.
6.CHECK FRONT DISC BRAKE
Check front disc brake. Refer to BR-39, "
BRAKE CALIPER ASSEMBLY : Inspection".
DTC Display Item Malfunction detected condition Possible causes
C1142 PRESS SEN CIRCUIT When a malfunction is detected in master cylinder
pressure sensor or control pressure sensor
*. Stop lamp switch system
ABS actuator and electric unit
(control unit)
Brake system
Revision: 2010 May2011 QX56
Page 613 of 5598
BRC-96
< DTC/CIRCUIT DIAGNOSIS >[WITH VDC]
C1142 PRESS SENSOR
Is the inspection result normal?
YES >> GO TO 7.
NO >> Repair or replace error-detected parts.
7.CHECK REAR DISC BRAKE
Check rear disc brake. Refer to BR-45, "
BRAKE CALIPER ASSEMBLY : Inspection".
Is the inspection result normal?
YES >> GO TO 8.
NO >> Repair or replace error-detected parts.
8.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
With CONSULT-III.
1. Erase Self-diagnosis result for “ABS”.
2. Start the engine and drive the vehicle for a short period of time.
3. Perform self-diagnosis for “ABS”.
Is DTC
“C1142” detected?
YES >> Replace ABS actuator and electr ic unit (control unit). Refer to BRC-137, "Removal and Installa-
tion"
NO >> Check ABS actuator and electric unit (control unit) harness connector and terminal for damage,
looseness and disconnection. Repair or replace error-detected parts.
Revision: 2010 May2011 QX56
Page 614 of 5598
![INFINITI QX56 2011 Factory Service Manual
C1143 STEERING ANGLE SENSORBRC-97
< DTC/CIRCUIT DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
C1143 STEERING ANGLE SENSOR
DTC LogicINFOID:0000000006222619
DTC DETECTION LOGIC
DTC CONFIRMAT INFINITI QX56 2011 Factory Service Manual
C1143 STEERING ANGLE SENSORBRC-97
< DTC/CIRCUIT DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
C1143 STEERING ANGLE SENSOR
DTC LogicINFOID:0000000006222619
DTC DETECTION LOGIC
DTC CONFIRMAT](/manual-img/42/57033/w960_57033-613.png)
C1143 STEERING ANGLE SENSORBRC-97
< DTC/CIRCUIT DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
C1143 STEERING ANGLE SENSOR
DTC LogicINFOID:0000000006222619
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK DTC DETECTION
With CONSULT-III.
1. Turn the ignition switch OFF to ON.
2. Perform self-diagnosis for “ABS”.
Is DTC
“C1143” detected?
YES >> Proceed to diagnosis procedure. Refer to BRC-97, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006222620
1.CHECK STEERING ANGLE SE NSOR MOUNTING CONDITION
Check steering angle sensor mounting condition. Refer to SR-14, "
Exploded View".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace error-detected parts.
2.CHECK STEERING ANGLE SENSOR POWER SUPPLY
1. Turn the ignition switch OFF.
2. Disconnect steering angle sensor harness connector.
3. Check voltage between steering angle sensor harness connector and ground.
4. Turn the ignition switch ON. CAUTION:
Never start engine.
5. Check voltage between steering angle sensor harness connector and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 3.
3.CHECK STEERING ANGLE SENSOR POWER SUPPLY CIRCUIT
1. Turn the ignition switch OFF.
2. Check 10A fuse (#7).
DTC Display Item Malfunction detected condition Possible causes
C1143 ST ANG SEN CIRCUIT When a malfunction is detected in steering angle sen-
sor. Harness or connector
Steering angle sensor
ABS actuator and electric unit
(control unit)
Fuse
Ignition power supply system
CAN communication line
Steering angle sensor — Voltage
Connector Terminal
M30 4 Ground Approx. 0 V
Steering angle sensor — Voltage
Connector Terminal
M30 4 Ground Battery voltage
Revision: 2010 May2011 QX56
Page 615 of 5598
![INFINITI QX56 2011 Factory Service Manual
BRC-98
< DTC/CIRCUIT DIAGNOSIS >[WITH VDC]
C1143 STEERING ANGLE SENSOR
3. Disconnect fuse block (J/B) harness connector.
4. Check continuity between steering angle sensor
harness connector and fuse INFINITI QX56 2011 Factory Service Manual
BRC-98
< DTC/CIRCUIT DIAGNOSIS >[WITH VDC]
C1143 STEERING ANGLE SENSOR
3. Disconnect fuse block (J/B) harness connector.
4. Check continuity between steering angle sensor
harness connector and fuse](/manual-img/42/57033/w960_57033-614.png)
BRC-98
< DTC/CIRCUIT DIAGNOSIS >[WITH VDC]
C1143 STEERING ANGLE SENSOR
3. Disconnect fuse block (J/B) harness connector.
4. Check continuity between steering angle sensor
harness connector and fuse block (J/B) harness connec-
tor.
5. Check continuity between steering angle sensor harness connector and ground.
Is the inspection result normal?
YES >> Perform trouble diagnosis for ignition power supply. Refer to PG-89, "Wiring Diagram - IGNITION
POWER SUPPLY -".
NO >> Repair or replace error-detected parts.
4.CHECK STEERING ANGL E SENSOR GROUND CIRCUIT
1. Turn the ignition switch OFF.
2. Check continuity between steering angle sensor harness connector and ground.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace error-detected parts.
5.CHECK TERMINAL
Check steering angle sensor pin terminals for damage or loose connection with harness connector.
Check fuse block (J/B) pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace error-detected parts.
6.CHECK CAN COMMUNICATION LINE
Check “STRG BRANCH LINE CIRCUIT”. Refer to LAN-81, "
Diagnosis Procedure".
Is the inspection result normal?
YES >> Replace ABS actuator and electr ic unit (control unit). Refer to BRC-137, "Removal and Installa-
tion".
NO >> Repair or replace error-detected parts. Refer to BRC-7, "
Precaution for Harness Repair".
Steering angle sensor Fuse block (J/B)
Continuity
Connector Terminal Connector Terminal
M30 4 M1 2A Existed
Steering angle sensor —Continuity
Connector Terminal
M30 4 Ground Not existed
Steering angle sensor —Continuity
Connector Terminal
M30 1 Ground Existed
Revision: 2010 May2011 QX56
Page 616 of 5598
![INFINITI QX56 2011 Factory Service Manual
C1144 INCOMPLETE STEERING ANGLE SENSOR ADJUSTMENT
BRC-99
< DTC/CIRCUIT DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
C1144 INCOMPLETE STEERING AN GLE SENSOR ADJUSTMENT
DTC LogicINFOID:0000 INFINITI QX56 2011 Factory Service Manual
C1144 INCOMPLETE STEERING ANGLE SENSOR ADJUSTMENT
BRC-99
< DTC/CIRCUIT DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
C1144 INCOMPLETE STEERING AN GLE SENSOR ADJUSTMENT
DTC LogicINFOID:0000](/manual-img/42/57033/w960_57033-615.png)
C1144 INCOMPLETE STEERING ANGLE SENSOR ADJUSTMENT
BRC-99
< DTC/CIRCUIT DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
C1144 INCOMPLETE STEERING AN GLE SENSOR ADJUSTMENT
DTC LogicINFOID:0000000006222621
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK DTC DETECTION
With CONSULT-III.
1. Turn the ignition switch OFF to ON.
2. Perform self-diagnosis for “ABS”.
Is DTC
“C1144” detected?
YES >> Proceed to diagnosis procedure. Refer to BRC-99, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006222622
1.ADJUST THE NEUTRAL POSITION OF STEERING ANGLE SENSOR
Perform neutral position adjustment of steering angle sensor. Refer to BRC-64, "
Work Procedure".
>> GO TO 2.
2.CHECK ABS ACTUATOR AND ERECTRIC UNIT (CONTROL UNIT)
With CONSULT-III.
Perform self-diagnosis for “ABS”.
Is DTC
“C1144” detected?
YES >> GO TO 3.
NO >> INSPECTION END
3.CHECK STEERING ANGLE SENSOR SYSTEM
1. Turn the ignition switch OFF.
2. Check steering angle sensor system. Refer to BRC-97, "
Diagnosis Procedure".
Is the inspection result normal?
YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-137, "Removal and Installa-
tion".
NO >> Repair or replace error-detected parts.
DTC Display Item Malfunction detected condition Possible causes
C1144 ST ANG SEN SIGNAL When neutral position adjustment of steering angle
sensor is not complete. Harness or connector
Steering angle sensor
ABS actuator and electric unit
(control unit)
Incomplete neutral position ad-
justment of steering angle sen-
sor
Revision: 2010 May2011 QX56