Page 1457 of 5598
![INFINITI QX56 2011 Factory Service Manual
DAS-492
< DTC/CIRCUIT DIAGNOSIS >[BSW]
U0126 STRG SEN CAN 1
U0126 STRG SEN CAN 1
DTC LogicINFOID:0000000006228233
DTC DETECTION LOGIC
NOTE:
If DTC “U0126” is detected along with DTC “U
1000”, INFINITI QX56 2011 Factory Service Manual
DAS-492
< DTC/CIRCUIT DIAGNOSIS >[BSW]
U0126 STRG SEN CAN 1
U0126 STRG SEN CAN 1
DTC LogicINFOID:0000000006228233
DTC DETECTION LOGIC
NOTE:
If DTC “U0126” is detected along with DTC “U
1000”,](/manual-img/42/57033/w960_57033-1456.png)
DAS-492
< DTC/CIRCUIT DIAGNOSIS >[BSW]
U0126 STRG SEN CAN 1
U0126 STRG SEN CAN 1
DTC LogicINFOID:0000000006228233
DTC DETECTION LOGIC
NOTE:
If DTC “U0126” is detected along with DTC “U
1000”, first diagnose the DTC “U1000”. Refer to DAS-486,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the BSW system ON.
3. Perform “All DTC Reading” with CONSULT-III.
4. Check if the “U0126” is detected as the current ma lfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U0126” detected as the current malfunction?
YES >> Refer to DAS-492, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006228234
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected ot her than “U0126” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communication system inspecti on. Repair or replace the malfunctioning parts.
Refer to DAS-486, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
BRC-51, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board dis-
play) Trouble diagnosis name DTC detecting condition Possible causes
U0126 (130) STRG SEN CAN CIR1 If ADAS control unit detects an error signal
that is received from steering angle sensor via
CAN communication
Steering angle sensor
Revision: 2010 May2011 QX56
Page 1458 of 5598
![INFINITI QX56 2011 Factory Service Manual
DAS
U0401 ECM CAN 1DAS-493
< DTC/CIRCUIT DIAGNOSIS > [BSW]
C
D
E
F
G H
I
J
K L
M B
N P A
U0401 ECM CAN 1
DTC LogicINFOID:0000000006228270
DTC DETECTION LOGIC
NOTE:
If DTC “U0401” is detected alon INFINITI QX56 2011 Factory Service Manual
DAS
U0401 ECM CAN 1DAS-493
< DTC/CIRCUIT DIAGNOSIS > [BSW]
C
D
E
F
G H
I
J
K L
M B
N P A
U0401 ECM CAN 1
DTC LogicINFOID:0000000006228270
DTC DETECTION LOGIC
NOTE:
If DTC “U0401” is detected alon](/manual-img/42/57033/w960_57033-1457.png)
DAS
U0401 ECM CAN 1DAS-493
< DTC/CIRCUIT DIAGNOSIS > [BSW]
C
D
E
F
G H
I
J
K L
M B
N P A
U0401 ECM CAN 1
DTC LogicINFOID:0000000006228270
DTC DETECTION LOGIC
NOTE:
If DTC “U0401” is detected along with DTC “U 1000”, first diagnose the DTC “U1000”. Refer to DAS-486,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the BSW system ON.
3. Perform “All DTC Readi ng” with CONSULT-III.
4. Check if the “U0401” is detected as the current ma lfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U0401” detected as the current malfunction?
YES >> Refer to DAS-493, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006228271
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “U0401” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communicati on system inspection. Repair or replace the malfunctioning parts.
Refer to DAS-486, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK ECM SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “S elf Diagnostic Result” of “ENGINE”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
EC-98, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board
display) Trouble diagnosis name DTC detecting condition Possible causes
U0401 (120) ECM CAN CIR1 If ADAS control unit detects an error signal
that is received from ECM via CAN communi-
cation
ECM
Revision: 2010 May2011 QX56
Page 1459 of 5598
![INFINITI QX56 2011 Factory Service Manual
DAS-494
< DTC/CIRCUIT DIAGNOSIS >[BSW]
U0402 TCM CAN 1
U0402 TCM CAN 1
DTC LogicINFOID:0000000006228272
DTC DETECTION LOGIC
NOTE:
If DTC “U0402” is detected along with DTC “U
1000”, first dia INFINITI QX56 2011 Factory Service Manual
DAS-494
< DTC/CIRCUIT DIAGNOSIS >[BSW]
U0402 TCM CAN 1
U0402 TCM CAN 1
DTC LogicINFOID:0000000006228272
DTC DETECTION LOGIC
NOTE:
If DTC “U0402” is detected along with DTC “U
1000”, first dia](/manual-img/42/57033/w960_57033-1458.png)
DAS-494
< DTC/CIRCUIT DIAGNOSIS >[BSW]
U0402 TCM CAN 1
U0402 TCM CAN 1
DTC LogicINFOID:0000000006228272
DTC DETECTION LOGIC
NOTE:
If DTC “U0402” is detected along with DTC “U
1000”, first diagnose the DTC “U1000”. Refer to DAS-486,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the BSW system ON.
3. Perform “All DTC Reading” with CONSULT-III.
4. Check if the “U0402” is detected as the current ma lfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U0402” detected as the current malfunction?
YES >> Refer to DAS-494, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006228273
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected ot her than “U0402” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communication system inspecti on. Repair or replace the malfunctioning parts.
Refer to DAS-486, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK TCM SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Sel f Diagnostic Result” of “TRANSMISSION”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
TM-78, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board dis-
play) Trouble diagnosis
name DTC detecting condition Possible causes
U0402 (122) TCM CAN CIRC1 If ADAS control unit detects an error signal
that is received from TCM via CAN communi-
cation
TCM
Revision: 2010 May2011 QX56
Page 1460 of 5598
![INFINITI QX56 2011 Factory Service Manual
DAS
U0405 ADAS CAN 2DAS-495
< DTC/CIRCUIT DIAGNOSIS > [BSW]
C
D
E
F
G H
I
J
K L
M B
N P A
U0405 ADAS CAN 2
DTC LogicINFOID:0000000006223933
DTC DETECTION LOGIC
NOTE:
If DTC “U0405” is detected al INFINITI QX56 2011 Factory Service Manual
DAS
U0405 ADAS CAN 2DAS-495
< DTC/CIRCUIT DIAGNOSIS > [BSW]
C
D
E
F
G H
I
J
K L
M B
N P A
U0405 ADAS CAN 2
DTC LogicINFOID:0000000006223933
DTC DETECTION LOGIC
NOTE:
If DTC “U0405” is detected al](/manual-img/42/57033/w960_57033-1459.png)
DAS
U0405 ADAS CAN 2DAS-495
< DTC/CIRCUIT DIAGNOSIS > [BSW]
C
D
E
F
G H
I
J
K L
M B
N P A
U0405 ADAS CAN 2
DTC LogicINFOID:0000000006223933
DTC DETECTION LOGIC
NOTE:
If DTC “U0405” is detected along with DTC “U1000”, first diagnose the DTC “U1000”. Refer to DAS-485, "
SIDE RADAR LH : DTC Logic"
(SIDE RADAR LEFT), DAS-485, "SIDE RADAR LH : DTC Logic" (SIDE RADAR RIGHT).
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the BSW system ON.
3. Perform “All DTC Reading” with CONSULT-III
4. Check if the U0405 is detected as the current ma lfunction in “Self Diagnostic Result” of “SIDE RADAR
RIGHT/LEFT”.
Is the DTC
“U0405” detected?
YES >> Refer to DAS-495, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006223934
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “U0405” in “S elf Diagnostic Result” of “SIDE RADAR RIGHT/LEFT”.
Is
“U1000” detected?
YES >> Perform the CAN communicati on system inspection. Repair or replace the malfunctioning parts.
Refer to DAS-485, "
SIDE RADAR LH : DTC Logic" (SIDE RADAR LEFT), DAS-486, "SIDE
RADAR RH : DTC Logic" (SIDE RADAR RIGHT).
NO >> GO TO 2.
2.CHECK ADAS CONTROL UNIT SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “S elf Diagnostic Result” of “ICC/ADAS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
DAS-440, "
DTC Index".
NO >> Replace side radar LH or RH. Refer to DAS-523, "
Removal and Installation".
DTC Trouble diagnosis name DTC detecting condition Possible cause
U0405 ADAS CAN CIR2 Side radar detected an error of ITS communication signal
that was received from ADAS control unit.
ADAS control unit.
Revision: 2010 May2011 QX56
Page 1461 of 5598
![INFINITI QX56 2011 Factory Service Manual
DAS-496
< DTC/CIRCUIT DIAGNOSIS >[BSW]
U0415 VDC CAN 1
U0415 VDC CAN 1
DTC LogicINFOID:0000000006228274
DTC DETECTION LOGIC
NOTE:
If DTC “U0415” is detected along with DTC “U
1000”, first dia INFINITI QX56 2011 Factory Service Manual
DAS-496
< DTC/CIRCUIT DIAGNOSIS >[BSW]
U0415 VDC CAN 1
U0415 VDC CAN 1
DTC LogicINFOID:0000000006228274
DTC DETECTION LOGIC
NOTE:
If DTC “U0415” is detected along with DTC “U
1000”, first dia](/manual-img/42/57033/w960_57033-1460.png)
DAS-496
< DTC/CIRCUIT DIAGNOSIS >[BSW]
U0415 VDC CAN 1
U0415 VDC CAN 1
DTC LogicINFOID:0000000006228274
DTC DETECTION LOGIC
NOTE:
If DTC “U0415” is detected along with DTC “U
1000”, first diagnose the DTC “U1000”. Refer to DAS-486,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the BSW system ON.
3. Perform “All DTC Reading” with CONSULT-III.
4. Check if the “U0415” is detected as the current ma lfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U0415” detected as the current malfunction?
YES >> Refer to DAS-496, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006228275
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected ot her than “U0415” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communication system inspecti on. Repair or replace the malfunctioning parts.
Refer to DAS-486, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
BRC-51, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board dis-
play) Trouble diagnosis name DTC detecting condition Possible causes
U0415 (126) VDC CAN CIR1 If ADAS control unit de
tects an error signal
that is received from ABS actuator and electric
unit (control unit) via CAN communication ABS actuator and electric unit (control
unit)
Revision: 2010 May2011 QX56
Page 1462 of 5598
![INFINITI QX56 2011 Factory Service Manual
DAS
U0428 STRG SEN CAN 2DAS-497
< DTC/CIRCUIT DIAGNOSIS > [BSW]
C
D
E
F
G H
I
J
K L
M B
N P A
U0428 STRG SEN CAN 2
DTC LogicINFOID:0000000006228276
DTC DETECTION LOGIC
NOTE:
If DTC “U0428” is det INFINITI QX56 2011 Factory Service Manual
DAS
U0428 STRG SEN CAN 2DAS-497
< DTC/CIRCUIT DIAGNOSIS > [BSW]
C
D
E
F
G H
I
J
K L
M B
N P A
U0428 STRG SEN CAN 2
DTC LogicINFOID:0000000006228276
DTC DETECTION LOGIC
NOTE:
If DTC “U0428” is det](/manual-img/42/57033/w960_57033-1461.png)
DAS
U0428 STRG SEN CAN 2DAS-497
< DTC/CIRCUIT DIAGNOSIS > [BSW]
C
D
E
F
G H
I
J
K L
M B
N P A
U0428 STRG SEN CAN 2
DTC LogicINFOID:0000000006228276
DTC DETECTION LOGIC
NOTE:
If DTC “U0428” is detected along with DTC “U 1000”, first diagnose the DTC “U1000”. Refer to DAS-486,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the BSW system ON.
3. Perform “All DTC Readi ng” with CONSULT-III.
4. Check if the “U0428” is detected as the current ma lfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U0428” detected as the current malfunction?
YES >> Refer to DAS-497, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006228277
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “U0428” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communicati on system inspection. Repair or replace the malfunctioning parts.
Refer to DAS-486, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK ABS ACTUATOR AND ELECTRIC UNIT (C ONTROL UNIT) SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
BRC-51, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board dis-
play) Trouble diagnosis name DTC detecting condition Possible causes
U0428 (131) STRG SEN CAN CIR2 If ADAS control unit detects an error signal
that is received from steering angle sensor via
CAN communication
Steering angle sensor
Revision: 2010 May2011 QX56
Page 1463 of 5598
![INFINITI QX56 2011 Factory Service Manual
DAS-498
< DTC/CIRCUIT DIAGNOSIS >[BSW]
U150B ECM CAN 3
U150B ECM CAN 3
DTC LogicINFOID:0000000006228278
DTC DETECTION LOGIC
NOTE:
If DTC “U150B” is detected along with DTC “U1000”, first diag INFINITI QX56 2011 Factory Service Manual
DAS-498
< DTC/CIRCUIT DIAGNOSIS >[BSW]
U150B ECM CAN 3
U150B ECM CAN 3
DTC LogicINFOID:0000000006228278
DTC DETECTION LOGIC
NOTE:
If DTC “U150B” is detected along with DTC “U1000”, first diag](/manual-img/42/57033/w960_57033-1462.png)
DAS-498
< DTC/CIRCUIT DIAGNOSIS >[BSW]
U150B ECM CAN 3
U150B ECM CAN 3
DTC LogicINFOID:0000000006228278
DTC DETECTION LOGIC
NOTE:
If DTC “U150B” is detected along with DTC “U1000”, first diagnose the DTC “U1000”. Refer \
to
DAS-486,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the BSW system ON.
3. Perform “All DTC Reading” with CONSULT-III.
4. Check if the “U150B” is detected as the current ma lfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U150B” detected as the current malfunction?
YES >> Refer to DAS-498, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006228279
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “U150B” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communication system inspecti on. Repair or replace the malfunctioning parts.
Refer to DAS-486, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK ECM SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “S elf Diagnostic Result” of “ENGINE”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
EC-98, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board dis-
play) Trouble diagnosis name DTC detecting condition Possible causes
U150B (157) ECM CAN CIRC 3
ADAS control unit detects an error signal that is
received from ECM via CAN communication ECM
Revision: 2010 May2011 QX56
Page 1464 of 5598
![INFINITI QX56 2011 Factory Service Manual
DAS
U150C VDC CAN 3DAS-499
< DTC/CIRCUIT DIAGNOSIS > [BSW]
C
D
E
F
G H
I
J
K L
M B
N P A
U150C VDC CAN 3
DTC LogicINFOID:0000000006228280
DTC DETECTION LOGIC
NOTE:
If DTC “U150C” is detected alon INFINITI QX56 2011 Factory Service Manual
DAS
U150C VDC CAN 3DAS-499
< DTC/CIRCUIT DIAGNOSIS > [BSW]
C
D
E
F
G H
I
J
K L
M B
N P A
U150C VDC CAN 3
DTC LogicINFOID:0000000006228280
DTC DETECTION LOGIC
NOTE:
If DTC “U150C” is detected alon](/manual-img/42/57033/w960_57033-1463.png)
DAS
U150C VDC CAN 3DAS-499
< DTC/CIRCUIT DIAGNOSIS > [BSW]
C
D
E
F
G H
I
J
K L
M B
N P A
U150C VDC CAN 3
DTC LogicINFOID:0000000006228280
DTC DETECTION LOGIC
NOTE:
If DTC “U150C” is detected along with DTC “U1000 ”, first diagnose the DTC “U1000”. Refer to DAS-486,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the BSW system ON.
3. Perform “All DTC Readi ng” with CONSULT-III.
4. Check if the “U150C” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U150C” detected as the current malfunction?
YES >> Refer to DAS-499, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006228281
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “U150C ” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communicati on system inspection. Repair or replace the malfunctioning parts.
Refer to DAS-486, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK ABS ACTUATOR AND ELECTRIC UNIT (C ONTROL UNIT) SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
BRC-51, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board dis-
play) Trouble diagnosis name DTC detecting condition Possible causes
U150C (158) VDC CAN CIRC 3 ADAS control unit detects an error signal that is
received from ABS actuator and electric unit
(control unit) via CAN communication ABS actuator and electric unit (control
unit)
Revision: 2010 May2011 QX56