Page 3721 of 5598
MIR-16
< WIRING DIAGRAM >
DOOR MIRROR SYSTEM
JCLWM5431GB
Revision: 2010 May2011 QX56
Page 3722 of 5598
DOOR MIRROR SYSTEMMIR-17
< WIRING DIAGRAM >
C
DE
F
G H
I
J
K
M A
B
MIR
N
O P
JCLWM5432GB
Revision: 2010 May2011 QX56
Page 3723 of 5598
MIR-18
< WIRING DIAGRAM >
DOOR MIRROR SYSTEM
JCLWM5433GB
Revision: 2010 May2011 QX56
Page 3724 of 5598
AUTO ANTI-DAZZLING INSIDE MIRROR SYSTEMMIR-19
< WIRING DIAGRAM >
C
DE
F
G H
I
J
K
M A
B
MIR
N
O P
AUTO ANTI-DAZZLING INSIDE MIRROR SYSTEM
Wiring Diagram - INSIDE MIRROR SYSTEM -INFOID:0000000006257227
JCLWM5434GB
Revision: 2010 May2011 QX56
Page 3725 of 5598
MIR-20
< WIRING DIAGRAM >
AUTO ANTI-DAZZLING INSIDE MIRROR SYSTEM
JCLWM5435GB
Revision: 2010 May2011 QX56
Page 3726 of 5598

DIAGNOSIS AND REPAIR WORKFLOWMIR-21
< BASIC INSPECTION >
C
DE
F
G H
I
J
K
M A
B
MIR
N
O P
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work FlowINFOID:0000000006257228
DETAILED FLOW
1.OBTAIN INFORMATION ABOUT SYMPTOM
Interview the customer to obtain the malfunction information (conditions and environment when the malfunc-
tion occurred) as much as possible when the customer brings the vehicle in.
>> GO TO 2.
2.CHECK DTC
Perform self-diagnosis for automatic dr ive positioner (ADP) with CONSULT-III.
Is any DTC detected?
YES >> Refer to ADP-31, "DTCIndex"
NO >> GO TO 3.
3.REPRODUCE THE MALFUNCTION INFORMATION
Check the malfunction on the vehicl e that the customer describes.
Inspect the relation of the symptoms and the condition when the symptoms occur.
>> GO TO 4.
4.IDENTIFY THE MALFUNCTIONING SYST EM WITH “SYMPTOM DIAGNOSIS”
Use “Symptom diagnosis” from the sympt om inspection result in step 3. Then identify where to start perform-
ing the diagnosis based on possible causes and symptoms.
>> GO TO 5.
5.IDENTIFY MALFUNCTIONING PART S WITH “COMPONENT DIAGNOSIS”
Perform the diagnosis with “Component di agnosis” of the applicable system.
>> GO TO 6.
6.REPAIR OR REPLACE THE MALFUNCTIONING PARTS
Repair or replace the specified malfunctioning parts.
>> GO TO 7.
7.FINAL CHECK
Check that malfunctions are not reproduced when obtai ning the malfunction information from the customer,
referring to the symptom inspection result in step 3.
Are all malfunctions corrected?
YES >> INSPECTION END
NO >> GO TO 4.
Revision: 2010 May2011 QX56
Page 3727 of 5598
MIR-22
< DTC/CIRCUIT DIAGNOSIS >
DOOR MIRROR REMOTE CONTROL SWITCH
DTC/CIRCUIT DIAGNOSIS
DOOR MIRROR REMOTE CONTROL SWITCH
OPEN/CLOSE SWITCH
OPEN/CLOSE SWITCH : Co mponent InspectionINFOID:0000000006257229
1.CHECK OPEN/CLOSE SWITCH
1. Turn ignition switch OFF.
2. Disconnect door mirror remote control switch connector.
3. Check continuity between door mirro r remote control switch terminals.
[Driver side]
[Passenger side]
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace door mirror remote control switch.
Door mirror remote control switch
Condition Continuity
Te r m i n a l
12 10
Open/close switchOPEN
Existed
13 8
12 8
CLOSE
13 10
Door mirror remote control switch Condition Continuity
Te r m i n a l
12 11
Open/close switchOPEN
Existed
13 9
12 9
CLOSE
13 11
Revision: 2010 May2011 QX56
Page 3728 of 5598
REVERSE INTERLOCK DOOR MIRROR DOES NOT OPERATE
MIR-23
< SYMPTOM DIAGNOSIS >
C
D E
F
G H
I
J
K
M A
B
MIR
N
O P
SYMPTOM DIAGNOSIS
REVERSE INTERLOCK DOOR MI RROR DOES NOT OPERATE
Diagnosis ProcedureINFOID:0000000006257230
1.CHECK DOOR MIRROR (MANUAL FUNCTION)
Check door mirror function with door mirror remote control switch.
Refer to ADP-126, "
DOOR MIRROR : Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts.
2.CHECK DTC
Check DTC for TCM.
Refer to TM-78, "
DTC Index".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace the malfunctioning parts.
3.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES >> Check intermittent incident. Refer to GI-40, "Intermittent Incident".
NO >> GO TO 1.
Revision: 2010 May2011 QX56