Page 2865 of 5598
EXT-10
< SYMPTOM DIAGNOSIS >
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Diagnostic Worksheet
INFOID:0000000006367802
PIIB8741E
Revision: 2010 May2011 QX56
Page 2866 of 5598
SQUEAK AND RATTLE TROUBLE DIAGNOSESEXT-11
< SYMPTOM DIAGNOSIS >
C
DE
F
G H
I
J
L
M A
B
EXT
N
O P
PIIB8742E
Revision: 2010 May2011 QX56
Page 2867 of 5598
EXT-12
< REMOVAL AND INSTALLATION >
FRONT BUMPER
REMOVAL AND INSTALLATION
FRONT BUMPER
Exploded ViewINFOID:0000000006367597
JMKIA5429GB
Revision: 2010 May2011 QX56
Page 2868 of 5598

FRONT BUMPEREXT-13
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
EXT
N
O P
Removal and InstallationINFOID:0000000006367598
REMOVAL
CAUTION:
Bumper fascia is made of resin. Never apply strong force to it, and be careful to prevent contact with
oil.
1. Fully open hood assembly.
2. Remove front grille. Refer to EXT-19, "
Removal and Installation".
3. Remove bumper molding. 1. Remove front fender drip cover. Refer to DLK-223, "
FRONT FENDER DRIP COVER : Removal and
Installation".
2. Remove bumper molding upper fixing screws (A) (LH and
RH).
3. Remove bumper molding fixing clips (A).
1. Bumper molding bracket LH 2. Energy absorber LH 3. Rivet
4. Bumper molding 5. Grommet 6. Bumper molding bracket RH
7. Energy absorber RH 8. Bumper fascia assembly 9. Front fog lamp RH
10. Front fog lamp finisher RH 11. Front grille lower molding 12. Front bumper grille (with ICC)
13. Front bumper grille (without ICC) 14. License plate bracket 15. Front fog lamp finisher LH
16. Front fog lamp LH 17. U nut 18. Bumper retainer bracket LH
19. Bumper retainer 20. Bumper side bracket LH 21. Grommet
22. Bumper side bracket RH 23. Grommet 24. Bumper molding stay RH
25. Bumper retainer bracket RH 26. Bumper retainer bracket CTR 27. Bumper molding stay LH
28. double-sided tape [t: 0.13 mm (0.005 in)]
: Pawl
: Metal clip
: Vehicle front
JMKIA5426ZZ
JMKIA5427ZZ
Revision: 2010 May2011 QX56
Page 2869 of 5598

EXT-14
< REMOVAL AND INSTALLATION >
FRONT BUMPER
4. Pull bumper molding (1) toward the direction shown in thefigure, and then disengage bumper molding fixing metal
clips (LH and RH).
5. Remove bumper molding.
4. Remove front over fender front side. Refer to EXT-26, "
Removal and Installation".
5. Remove clips of bumper upper side.
6. Remove bumper fascia assembly fixing screws (A) (LH and RH).
7. Pull bumper fascia assembly toward the vehicle outside as shown by the arrow in the figure, and then disengage the
bumper fascia assembly from bumper side brackets (LH and
RH).
8. Disconnect corner sensor harness c onnector and fog lamp harness connector.
9. Remove bumper fascia assembly. CAUTION:
When removing bumper fascia assembly, 2 workers are required so as to prevent it from dropping.
10. Remove the following parts after removing bumper fascia assembly. Front grille lower molding.
Front bumper grille.
Sonar sensor (LH and RH). Refer to AV-239, "
Removal and Installation".
Front fog lamp assembly (LH and RH). Refer to EXL-128, "
Removal and Installation" .
Front fog lamp finishers (LH and RH)
Bumper side bracket (LH and RH)
License plate bracket
11. Remove bumper upper retainer.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
NOTE:
: Metal clip
JMKIA5428ZZ
JMKIA5430ZZ
: Pawl
JMKIA5431ZZ
Revision: 2010 May2011 QX56
Page 2870 of 5598

FRONT BUMPEREXT-15
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
EXT
N
O P
The following table shows the specified values for checking normal installation status.
Fitting adjustment cannot be performed.
JMKIA5454ZZ
Portion Clearance Surf ace height difference
Front grille –
Hood A – A3.7 – 8.3 mm
(0.146 – 0.327 in) (-0.9) – (+3.9) mm
[(-0.035) – (+0.154) in]
Bumper fascia assembly –
Front bumper molding B – B0.1 – 3.4 mm
(0.004 – 0.134 in) (-1.9) – (+1.9) mm
[(-0.075) – (+0.075) in]
Front bumper molding –
Headlamp C – C0.1 – 2.5 mm
(0.004 – 0.098 in) —
Front bumper molding –
Hood D – D1.2 – 5.8 mm
(0.047 – 0.228 in) (-2.4) – (+2.4) mm
[(-0.094) – (+0.094)]
Front bumper molding–
Headlamp E – E0.1 – 2.5 mm
(0.004 – 0.098 in) —
Bumper fascia assembly –
Headlamp F – F0.2 – 3.1 mm
(0.008 – 0.122 in) 0.5 – 3.5 mm
(0.020 – 0.138 in)
Front fender –
Front bumper molding G – G0.0 – 0.7 mm
(0.000 – 0.028 in) (-1.0) – (+1.0) mm
[(-0.039) – (+0.039) in]
Front fender –
Bumper fascia assembly H – H0.0 – 0.8 mm
(0.000 – 0.031 in) (-0.7) – (+1.3) mm
[(-0.028) – (+0.051) in]
Revision: 2010 May2011 QX56
Page 2871 of 5598
EXT-16
< REMOVAL AND INSTALLATION >
REAR BUMPER
REAR BUMPER
Exploded ViewINFOID:0000000006367599
1. Bumper side bracket LH 2. Bumper stay LH 3. Bumper side reinforcement LH
4. Bumper side stay LH 5. Grommet 6. Bumper fascia assembly
7. Grommet 8. Reflex reflector LH 9. Bumper stay LH
JMKIA5813ZZ
Revision: 2010 May2011 QX56
Page 2872 of 5598

REAR BUMPEREXT-17
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
EXT
N
O P
Removal and InstallationINFOID:0000000006367600
REMOVAL
CAUTION:
Bumper fascia is made of resin. Never apply strong force to it, and be careful to prevent contact with
oil.
1. Fully open back door assembly.
2. Remove rear combination lamp (LH and RH). Refer to EXL-138, "
Removal and Installation".
3. Remove bumper fascia fixing clips (A) and screws (B) (LH and RH).
4. Remove rear over fender fixing screws.
5. Remove bumper fascia lower mounting bolts.
6. Remove screws (A) of bumper fascia front end upper (LH and RH).
7. Pull bumper fascia assembly toward the vehicle outside as shown by the arrow in the figure, and then disengage the
bumper fascia assembly from bumper side brackets (LH and
RH).
8. Remove bumper fascia assembly. CAUTION:
When removing bumper fascia assembly, 2 workers ar e required so as to prevent it from dropping.
9. Remove the following parts after removing rear bumper fascia. Bumper side brackets (LH and RH)
Reflex reflector (LH and RH)
Bumper stay bracket (LH and RH)
Bumper stay (LH and RH)
10. Bumper lower finisher 11. Reflex reflector RH 12. Bumper stay RH
13. Bumper side stay RH 14. Energy absorber 15. Bumper side reinforcement RH
16. Bumper stay RH 17. Bumper side bracket RH
JMKIA5370ZZ
JMKIA5460ZZ
: Pawl
JMKIA5461ZZ
Revision: 2010 May2011 QX56