Page 2105 of 4801
HOW TO SELECT PISTON AND BEARINGEM-107
< UNIT DISASSEMBLY AND ASSEMBLY > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
Connecting Rod Bearing Selection Table
Connecting Rod Bearing Grade Table. Refer to
EM-111, "Standard and Limit"
.
Undersize Bearing Usage Guide
• When the specified oil clearance is not obtained with standard size connecting rod bearing, use undersize
(US) bearing.
• When using undersize bearing, measure the bearing inner diameter with bearing installed, and grind the
crankshaft pin so that the oil clearance satisfies the standard.
Bearing Undersize Table
Unit: mm (in)
CAUTION:
In grinding the crankshaft pin to use undersize bearings, do not
damage the fillet R (All crankshaft pins).
HOW TO SELECT A MAIN BEARING
When New Cylinder Block and Crankshaft are Used:
AWBIA0021GB
Size U.S. Thickness
0.25 (0.0098) 1.622 - 1.630 (0.0639 - 0.0642)
KBIA0148E
Revision: November 20132014 Altima NAM
Page 2106 of 4801
![NISSAN TEANA 2014 Service Manual
EM-108
< UNIT DISASSEMBLY AND ASSEMBLY >[QR25DE]
HOW TO SELECT PISTON AND BEARING
1. "Main Bearing Selection Table" rows correspond to bearing
housing grade on rear left side of cylinder block.
• NISSAN TEANA 2014 Service Manual
EM-108
< UNIT DISASSEMBLY AND ASSEMBLY >[QR25DE]
HOW TO SELECT PISTON AND BEARING
1. "Main Bearing Selection Table" rows correspond to bearing
housing grade on rear left side of cylinder block.
•](/manual-img/5/57390/w960_57390-2105.png)
EM-108
< UNIT DISASSEMBLY AND ASSEMBLY >[QR25DE]
HOW TO SELECT PISTON AND BEARING
1. "Main Bearing Selection Table" rows correspond to bearing
housing grade on rear left side of cylinder block.
• If there is a corrected stamp ma rk on the cylinder block, use it
as a correct reference.
2. Apply journal diameter grade (A) stamped on crankshaft front side to column in "Main Bearing Selection Table".
3. Find value at crossing of row and column in "Main Bearing Selection Table". CAUTION:
• There are two main bearing selecti on tables. One is for odd-numbered journals (1, 3, and 5) and
the other is for even-numbered journals (2 and 4) . Make certain to use the appropriate table. This
is due to differences in the specified clearances.
4. Apply the symbol obtained to "Main Bearing Grade Table" to select. NOTE:
• Service parts are available as a set of both upper and lower.
When Cylinder Block and Crankshaft are Reused:
1. Measure inner diameter of cylinder block main bear ing housing and outer diameter of crankshaft journal.
2. Apply measurement in above step 1 to the "Main Bearing Selection Table".
3. Follow steps 3 and 4 in "When New Cylinder Block and Crankshaft are Used".
SBIA0283E
(B) : Pin diameter grade
AWBIA0017ZZ
Revision: November 20132014 Altima NAM
Page 2107 of 4801
HOW TO SELECT PISTON AND BEARINGEM-109
< UNIT DISASSEMBLY AND ASSEMBLY > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
Main Bearing Selection Table (No.1, 3, and No.5 journals)
KBIA0149E
Revision: November 20132014 Altima NAM
Page 2108 of 4801
EM-110
< UNIT DISASSEMBLY AND ASSEMBLY >[QR25DE]
HOW TO SELECT PISTON AND BEARING
Main Bearing Selection Table (No.2,and 4 journals)
Main Bearing Grade Table (All Journals) Refer to
EM-111, "Standard and Limit".
Use Undersize Bearing Usage Guide
• Use undersize (U.S.) bearing when oil clearance with standar d size main bearing is not within specification.
• When using undersize (U.S.) bearing, measure the bear ing inner diameter with the bearing installed and
grind journal until oil clearance falls within specification.
Bearing Undersize Table
Unit: mm (in)
CAUTION:
Do not damage fillet R when grinding crankshaft journal in
order to use an undersize bearing (all journals).
KBIA0150E
Size U.S. Thickness
0.25 (0.0098) 2.106 - 2.114 (0.0829 - 0.0832)
KBIA0148E
Revision: November 20132014 Altima NAM
Page 2109 of 4801
![NISSAN TEANA 2014 Service Manual
SERVICE DATA AND SPECIFICATIONS (SDS)EM-111
< SERVICE DATA AND SPECIFICATIONS (SDS) [QR25DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (S NISSAN TEANA 2014 Service Manual
SERVICE DATA AND SPECIFICATIONS (SDS)EM-111
< SERVICE DATA AND SPECIFICATIONS (SDS) [QR25DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (S](/manual-img/5/57390/w960_57390-2108.png)
SERVICE DATA AND SPECIFICATIONS (SDS)EM-111
< SERVICE DATA AND SPECIFICATIONS (SDS) [QR25DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Standard and LimitINFOID:0000000009460513
GENERAL SPECIFICATIONS
VA LV E T I M I N G
Unit: degree
*1: When running at idle with engine coolant temperature more than 60
°C (140 °F).
Cylinder arrangement
In-line 4
Displacement cm
3 (in3) 2,488 (151.82)
Bore and stroke mm (in) 89.0 x 100 (3.50 x 3.94)
Valve arrangement DOHC
Firing order 1-3-4-2
Number of piston rings Compression 2
Oil 1
Compression ratio 10.0:1
Compression pressure
kPa (kg/cm
2, psi) / 250 rpm Standard 1410 (14.4, 204.5)
Minimum 1220 (12.4, 176.9)
Differential limit between cylinders 100 (1.0, 14)
Va l v e t i m i n g : Intake valve
: Exhaust valve
ab c de f
VTC Minimum phasing
(Mechanical)
*1224 244 5 69 3 41
VTC Maximum phasing
(Mechanical)
*2224 244 35 29 48 4
Intermediate lock phasing
(Mechanical)
*3224 244 5 59 3 41
ALBIA0875GBALBIA0876GB
ALBIA0877GB
Revision: November 20132014 Altima NAM
Page 2110 of 4801
EM-112
< SERVICE DATA AND SPECIFICATIONS (SDS) [QR25DE]
SERVICE DATA AND SPECIFICATIONS (SDS)
*2: When the intake or exhaust valve opening angle is at the maximum.
*3: When starting the engine with engine coolant temperature 60
°C (140 °F) or less.
DRIVE BELTS
EXHAUST MANIFOLD
Unit: mm (in)
SPARK PLUG
Unit: mm (in)
*: Always check with the Parts Department for the latest parts information.
CYLINDER HEAD
Unit: mm (in)
VA LV E
Valve Dimensions
Unit: mm (in)
Tension of drive belts Auto adjustment by drive belt auto-tensioner
Surface distortion Description Limit
Exhaust manifold 0.3 (0.012)
Make DENSO
Type* Standard FXE20HE11C
Gap (nominal) 1.1 (0.043)
Description Limit
Head surface distortion 0.1 (0.004)
Description Standard
Spark plug tube installation height 41.7 (1.642)
PBIC0283E
Valve head diameter (D) Intake 35.5 - 35.8 (1.398 - 1.409)
Exhaust 30.3 - 30.6 (1.193 - 1.205)
SEM188
Revision: November 20132014 Altima NAM
Page 2111 of 4801
![NISSAN TEANA 2014 Service Manual
SERVICE DATA AND SPECIFICATIONS (SDS)EM-113
< SERVICE DATA AND SPECIFICATIONS (SDS) [QR25DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
Valve Clearance
Unit: mm (in)
* Approximately 80
°C (176 °F)
Available NISSAN TEANA 2014 Service Manual
SERVICE DATA AND SPECIFICATIONS (SDS)EM-113
< SERVICE DATA AND SPECIFICATIONS (SDS) [QR25DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
Valve Clearance
Unit: mm (in)
* Approximately 80
°C (176 °F)
Available](/manual-img/5/57390/w960_57390-2110.png)
SERVICE DATA AND SPECIFICATIONS (SDS)EM-113
< SERVICE DATA AND SPECIFICATIONS (SDS) [QR25DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
Valve Clearance
Unit: mm (in)
* Approximately 80
°C (176 °F)
Available Valve Lifter
Unit: mm (in)
Valve length (L) Intake 101.72 (4.0074)
Exhaust 102.78 (4.0464)
Valve stem diameter (d) Intake 5.965 - 5.980 (0.2348 - 0.2354)
Exhaust 5.955 - 5.970 (0.2344 - 0.2350)
Valve seat angle α Intake
45°15 ′ - 45 °45 ′
Exhaust
Valve margin (T) Intake 1.08 (0.0425)
Exhaust 1.38 (0.0543)
Cold Hot*
Intake 0.24 - 0.32 (0.009 - 0.013) 0.304 - 0.416 (0.012 - 0.016)
Exhaust 0.26 - 0.34 (0.010 - 0.013) 0.308 - 0.432 (0.012 - 0.017)
Thickness Identification mark (Stamp)*
3.00 (0.1181) 300H
3.02 (0.1189) 302H
3.04 (0.1197) 304H
3.06 (0.1205) 306H
3.08 (0.1213) 308H
3.10 (0.1220) 310H
3.12 (0.1228) 312H
3.14 (0.1236) 314H
3.16 (0.1244) 316H
3.18 (0.1252) 318H
3.20 (0.1260) 320H
3.22 (0.1268) 322H
3.24 (0.1276) 324H
3.26 (0.1283) 326H
3.28 (0.1291) 328H
3.30 (0.1299) 330H
3.32 (0.1307) 332H
3.34 (0.1315) 334H
3.36 (0.1323) 336H
KBIA0119E
Revision: November 20132014 Altima NAM
Page 2112 of 4801
![NISSAN TEANA 2014 Service Manual
EM-114
< SERVICE DATA AND SPECIFICATIONS (SDS) [QR25DE]
SERVICE DATA AND SPECIFICATIONS (SDS)
*: Always check with the Parts Department for the latest parts information.
Valve Spring
Valve Lifter
Un NISSAN TEANA 2014 Service Manual
EM-114
< SERVICE DATA AND SPECIFICATIONS (SDS) [QR25DE]
SERVICE DATA AND SPECIFICATIONS (SDS)
*: Always check with the Parts Department for the latest parts information.
Valve Spring
Valve Lifter
Un](/manual-img/5/57390/w960_57390-2111.png)
EM-114
< SERVICE DATA AND SPECIFICATIONS (SDS) [QR25DE]
SERVICE DATA AND SPECIFICATIONS (SDS)
*: Always check with the Parts Department for the latest parts information.
Valve Spring
Valve Lifter
Unit: mm (in)
Valve Oil Seal
Unit: mm (in)
Valve Guide
3.38 (0.1331) 338H
3.40 (0.1339) 340H
3.42 (0.1346) 342H
3.44 (0.1354) 344H
3.46 (0.1362) 346H
3.48 (0.1370) 348H
3.50 (0.1378) 350H Thickness Identification mark (Stamp)*
KBIA0119E
Free height standard
mm (in) Intake 47.92 - 48.12 (1.8866 - 1.8945)
Exhaust 48.65 - 48.85 (1.9154 - 1.9232)
Installation height mm (in) Intake 36.96 (1.4551)
Exhaust 36.96 (1.4551)
Installation load N (kg - f, lb–f) Intake 151 - 175 (15.4 - 17.8, 34 - 39)
Exhaust 151 - 175 (15.4 - 17.8, 34 - 39)
Height during valve open mm (in) Intake 26.76 (1.0535)
Exhaust 28.46 (1.1205)
Load with valve open N (kg-f, lb-f) Intake 335 - 383 (34.2 - 39.1, 75.3 - 86.1)
Exhaust 300 - 342 (30.6 - 34.9, 67.4 - 76.9)
Identification color Intake White
Exhaust Light blue
Out-of-square mm (in) 1.0 (0.0394) 1.0 (0.0394)
Description Standard
Valve lifter outer diameter 33.977 - 33.987 (1.3377 - 1.3381)
Valve lifter bore inner diameter 34.000 - 34.021 (1.3386 - 1.3394)
Clearance between lifter and lifter guide 0.013 - 0.044 (0.0005 - 0.0017)
Description Standard
Valve oil seal installation height (A) 12.1 (0.476)
Revision: November 20132014 Altima NAM