2014 NISSAN TEANA ad blue

BRM-2
< VEHICLE INFORMATION >
BODY EXTERIOR PAINT COLOR
VEHICLE INFORMATION
BODY EXTERIOR PAINT COLOR
Body Exterior Paint ColorINFOID:0000000009464961
M = Metallic, S = Solid, 2S = Solid and Clear, 2P = 2-Coat Pearl, 3P = 3-Coat Pearl, PM = Pearl Metallic, t = Primerless Diamond Clear
coat, Cr2P = Chromium plate, Black is solvent based, all others are water based.
AWKIA2219ZZ
Component Color code CAJ K23 KAH KH3 NAH QAB RBD KAD
Description Brown Silver Beige Black Red White Blue Grey
Paint type MMMSMPM M
Hard clear coatttttttt t
1. Outside door handle Chromium
plate Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P
2. Fuel filler lid Body color CAJ K23 KAH KH3 NAH QAB RBD KAD
3. Rear bumper fascia Body color CAJ K23 KAH KH3 NAH QAB RBD KAD
4. License lamp finisher Chromium
plate Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P
5. Lower rocker finisher Body color CAJ K23 KAH KH3 NAH QAB RBD KAD
6. Body side molding Chromium
plate Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P
7. Door mirror Finisher Body co lor CAJ K23 KAH KH3 NAH QAB RBD KAD
8. Front bumper fascia Body color CAJ K23 KAH KH3 NAH QAB RBD KAD
9. Front grille Center Black KH3 KH3 KH3 KH3 KH3 KH3 KH3 KH3
Surround Chromium
plate Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P
Revision: November 20132014 Altima NAM

DAS
ADDITIONAL SERVICE WHEN REPLACING REAR VIEW CAMERA
DAS-37
< BASIC INSPECTION > [ITS CONTROL UNIT]
C
D E
F
G H
I
J
K L
M B
N P
A
ADDITIONAL SERVICE WHEN RE PLACING REAR VIEW CAMERA
DescriptionINFOID:0000000009464663
Always perform the calibration after removing and installing or replacing the rear view camera.
CAUTION:
The system does not operate normally unless the rear view camera aiming adjustment is performed.
Always perform it.
Work ProcedureINFOID:0000000009464664
1.CAMERA AIMING ADJUSTMENT
Perform the camera aiming adjustment with CONSULT. Refer to DAS-38, "Description"
.
>> GO TO 2.
2.PERFORM SELF-DIAGNOSIS
Perform the self-diagnosis of rear view camera with CONSULT. Check if any DTC is detected.
Is any DTC detected?
YES >> Perform the trouble diagnosis for the detected DTC. Refer to DAS-20, "DTC Index".
NO >> GO TO 3.
3.LDW/BSW SYSTEM ACTION TEST
1. Perform the LDW/BSW syst em action test. Refer to DAS-35, "Description"
.
2. Check that the LDW/BSW system operates normally.
Is the inspection result normal?
YES >> Inspection End.
NO >> GO TO 4.
4.LDW/BSW ACTIVE TEST
1. Perform WASH ACTIVE on Active Test using CONSULT.
2. Perform air and washer tube connection check by AIR & WASH ACTIVE on Active Test:
(1) Washer fluid output count on the rear view camera is 3 to 5 times → OK
(2) Washer fluid output count on the rear view camera is 10 times → Check tube with yellow marking
(3) Washer fluid output count on the rear view camera is 1 time → Check tube with green marking
(4) No washer fluid output → Check tube with blue marking or check valve
>> Inspection End.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS-106
< BASIC INSPECTION >[LDW]
ADDITIONAL SERVICE WHEN
REPLACING REAR VIEW CAMERA
ADDITIONAL SERVICE WHEN R EPLACING REAR VIEW CAMERA
DescriptionINFOID:0000000009464739
Always perform the calibration after removing and installing or replacing the rear view camera.
CAUTION:
The system does not operate normally unless the rear view camera aiming adjustment is performed.
Always perform it.
Work ProcedureINFOID:0000000009464740
1.CAMERA AIMING ADJUSTMENT
Perform the camera aiming adjustment with CONSULT. Refer to DAS-107, "Description"
.
>> GO TO 2.
2.PERFORM SELF-DIAGNOSIS
Perform the self-diagnosis of rear view camera with CONSULT. Check if any DTC is detected.
Is any DTC detected?
YES >> Perform the trouble diagnosis fo r the detected DTC. Refer to DAS-89, "DTC Index".
NO >> GO TO 3.
3.LDW/BSW SYSTEM ACTION TEST
1. Perform the LDW/BSW system action test. Refer to DAS-104, "Description"
.
2. Check that the LDW/BSW system operates normally.
Is the inspection result normal?
YES >> Inspection End.
NO >> GO TO 4.
4.LDW/BSW ACTIVE TEST
1. Perform WASH ACTIVE on Active Test using CONSULT.
2. Perform air and washer tube connection check by AIR & WASH ACTIVE on Active Test:
(1) Washer fluid output count on the rear view camera is 3 to 5 times → OK
(2) Washer fluid output count on the rear view camera is 10 times → Check tube with yellow marking
(3) Washer fluid output count on the rear view camera is 1 time → Check tube with green marking
(4) No washer fluid output → Check tube with blue marking or check valve
>> Inspection End.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS
ADDITIONAL SERVICE WHEN REPLACING REAR VIEW CAMERA
DAS-181
< BASIC INSPECTION > [BSW]
C
D E
F
G H
I
J
K L
M B
N P
A
ADDITIONAL SERVICE WHEN RE PLACING REAR VIEW CAMERA
DescriptionINFOID:0000000009464823
Always perform the calibration after removing and installing or replacing the rear view camera.
CAUTION:
The system does not operate normally unless the rear view camera aiming adjustment is performed.
Always perform it.
Work ProcedureINFOID:0000000009464824
1.CAMERA AIMING ADJUSTMENT
Perform the camera aiming adjustment with CONSULT. Refer to DAS-182, "Description"
.
>> GO TO 2.
2.PERFORM SELF-DIAGNOSIS
Perform the self-diagnosis of rear view camera with CONSULT. Check if any DTC is detected.
Is any DTC detected?
YES >> Perform the trouble diagnosis for the detected DTC. Refer to DAS-164, "DTC Index".
NO >> GO TO 3.
3.LDW/BSW SYSTEM ACTION TEST
1. Perform the LDW/BSW syst em action test. Refer to DAS-179, "Description"
.
2. Check that the LDW/BSW system operates normally.
Is the inspection result normal?
YES >> Inspection End.
NO >> GO TO 4.
4.LDW/BSW ACTIVE TEST
1. Perform WASH ACTIVE on Active Test using CONSULT.
2. Perform air and washer tube connection check by AIR & WASH ACTIVE on Active Test:
(1) Washer fluid output count on the rear view camera is 3 to 5 times → OK
(2) Washer fluid output count on the rear view camera is 10 times → Check tube with yellow marking
(3) Washer fluid output count on the rear view camera is 1 time → Check tube with green marking
(4) No washer fluid output → Check tube with blue marking or check valve
>> Inspection End.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS
OPERATIONDAS-231
< SYSTEM DESCRIPTION > [MOD]
C
D E
F
G H
I
J
K L
M B
N P
A
OPERATION
System Display and WarningINFOID:0000000009464891
INDICATOR AND WARNING LAMP
The MOD system can be turned ON or OFF for the current ignition cycle using the warning system switch.
When toggled between ON and OFF, the indicator will appear on the right side of the rear view camera screen.
DISPLAY AND WARNING OPERATION
No. Name Description
1 MOD indicator (blue)
• Turns ON while MOD system is ON
• Under the following conditions, the MOD indicator (blue) will blink.
- When the VDC system (except TCS function) or ABS operates.
- When the VDC system is turned off.
MOD warning lamp (orange) • Turns ON when MOD system is malfunctioning
• Blinks under the following conditions:
- When the component temperature reaches high level.
- When rear view camera blockage is detected.
Vehicle condition/Driver's operation
Moving Ob- ject Detec- tion ON
indicator Vehicle speed
(Approx.)
[km/h (MPH)] Status of vehi-
cle detection
within detec- tion area Indication on the
Moving Object Detection indicator Buzzer
OFF — — OFF OFF
Blue Less than ap-
prox.
8 km/h ( 5 MPH) Ve h i c l e i s
detected ON ON
Approx.
8 km/h ( 5
MPH) or more Vehicle is ab-
sent ON OFF
Ve h i c l e i s detected ON OFF
Vehicle is not detected ON OFF
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS-254
< BASIC INSPECTION >[MOD]
ACTION TEST
ACTION TEST
DescriptionINFOID:0000000009464902
• Perform action test to verify the customer's concern.
• Perform action test and check the syst em operation after system diagnosis.
WARNING:
Be careful of traffic conditions and safety ar ound the vehicle when performing road test.
CAUTION:
• Fully understand the following it ems well before the road test;
- Precautions: Refer to DAS-73, "Precaution for LDW System Service"
.
- System description for LDW: Refer to DAS-77, "System Description"
.
- System description for BSW: Refer to DAS-152, "System Description"
.
- System description for MOD: Refer to DAS-228, "System Description"
.
- Handling precaution: Refer to DAS-82, "Precautions for Lane Departure Warning"
.
Inspection ProcedureINFOID:0000000009464903
WARNING:
Be careful of traffic conditions and safety ar ound the vehicle when performing road test.
CAUTION:
• Fully understand the following it ems well before the road test;
- Precautions: Refer to DAS-73, "Precaution for LDW System Service"
.
- System description for LDW: Refer to DAS-77, "System Description"
.
- System description for BSW: Refer to DAS-152, "System Description"
.
- System description for MOD: Refer to DAS-228, "System Description"
.
- Handling precaution: Refer to DAS-232, "Precautions for Moving Objects Detection"
.
1.CHECK MOD SYSTEM SETTING
1. Start the engine.
2. Check that the MOD system setting can be enabl ed/disabled on the vehicle information display.
3. Turn OFF the ignition switch and wait for 30 seconds or more.
4. Check that the previous setting is saved when the engine starts again.
>> GO TO 2.
2.ACTION TEST FOR MOD
1. Enable the setting of the MOD system on the vehicle information display.
2. Turn warning systems switch ON (w arning systems ON indicator is ON).
3. Check the MOD operation according to the following table.
NOTE:
After the operating conditions of warning are satisfi ed, the warning continues until the vehicle reaches a
higher speed. Refer to DAS-228, "System Description"
.
>> Inspection End.
Vehicle condition/ Driver's operation Vehicle response
Moving Object De-
tection ON indicator Vehicle speed
(Approx.)
[km/h (MPH)] Status of vehicle detection
within detection area Indication on the Moving Object Detection
indicator Buzzer
OFF — — OFF OFF
Blue Less than approx.
8 km/h (5 MPH) Vehicle is detected ON ON
Approx. 8 km/h (5
MPH) or more Vehicle is absent ON OFF
Vehicle is detected ON OFF
Vehicle is not detected ON OFF
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS
ADDITIONAL SERVICE WHEN REPLACING REAR VIEW CAMERA
DAS-255
< BASIC INSPECTION > [MOD]
C
D E
F
G H
I
J
K L
M B
N P
A
ADDITIONAL SERVICE WHEN RE PLACING REAR VIEW CAMERA
DescriptionINFOID:0000000009464904
Always perform the calibration after removing and installing or replacing the rear view camera.
CAUTION:
The system does not operate normally unless the rear view camera aiming adjustment is performed.
Always perform it.
Work ProcedureINFOID:0000000009464905
1.CAMERA AIMING ADJUSTMENT
Perform the camera aiming adjustment with CONSULT. Refer to DAS-256, "Description"
.
>> GO TO 2.
2.PERFORM SELF-DIAGNOSIS
Perform the self-diagnosis of rear view camera with CONSULT. Check if any DTC is detected.
Is any DTC detected?
YES >> Perform the trouble diagnosis for the detected DTC. Refer to DAS-239, "DTC Index".
NO >> GO TO 3.
3.LDW/BSW SYSTEM ACTION TEST
1. Perform the LDW/BSW syst em action test. Refer to DAS-254, "Description"
.
2. Check that the LDW/BSW system operates normally.
Is the inspection result normal?
YES >> Inspection End.
NO >> GO TO 4.
4.LDW/BSW ACTIVE TEST
1. Perform WASH ACTIVE on Active Test using CONSULT.
2. Perform air and washer tube connection check by AIR & WASH ACTIVE on Active Test:
(1) Washer fluid output count on the rear view camera is 3 to 5 times → OK
(2) Washer fluid output count on the rear view camera is 10 times → Check tube with yellow marking
(3) Washer fluid output count on the rear view camera is 1 time → Check tube with green marking
(4) No washer fluid output → Check tube with blue marking or check valve
>> Inspection End.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EM-78
< REMOVAL AND INSTALLATION >[QR25DE]
CYLINDER HEAD
4. Install new valve oil seal using Tool (A) as shown.
5. Install valve. • Install larger diameter to intake side.
6. Install valve spring with valve spring seat (1). • Install valve spring so that the identification color faces upward
(A).
• Install smaller pitch to cylinder head side (B).
• Confirm the identification color of the valve spring.
• Intake: white
• Exhaust: light blue
7. Install valve spring retainer.
8. Install valve collet. • Compress valve spring using Tools. Install valve collet with amagnet hand.
CAUTION:
When working take care not to damage valve lifter holes.
• Tap valve stem edge lightly with a plastic hammer after instal-
lation to check its installed condition.
9. Install valve lifter.
10. Install spark plug tube.
a. Remove old liquid gasket from cylinder head mounting hole.
b. Apply liquid gasket all around on spark plug tube with a 12 mm (0.47 in) width from edge of spark plug tube on the press fit side.
• Use Three Bond or equivalent. Refer to GI-21, "Recom-
mended Chemical Products and Sealants".
c. Press fit spark plug tube so that height (H) is as shown.
CAUTION:
• When press fitting be careful not to deform spark plug
tube.
• After press fitting, wipe off any protruding liquid gasket on top surface of cylinder head.
Inspection After DisassemblyINFOID:0000000009460506
CYLINDER HEAD DISTORTION
Oil seal installed height (H) : 12.1 mm (0.476 in)
Tool number : KV10115600 (J-38958)
ALBIA0864GB
JPBIA4479ZZ
Tool number (A) : KV10116200 (J-26336-A)
Tool number (B) : KV10109220 ( — )
Tool number (C) : KV10115900 (J-26336-20)
JPBIA1365ZZ
Press fit height (H) standard value : 41.7 mm (1.642 in)
ALBIA0870GB
Revision: November 20132014 Altima NAM