Page 257 of 4801
![NISSAN TEANA 2014 Service Manual
VDC OFF SWITCHBRC-111
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace malfunctioning components.
NISSAN TEANA 2014 Service Manual
VDC OFF SWITCHBRC-111
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace malfunctioning components.](/manual-img/5/57390/w960_57390-256.png)
VDC OFF SWITCHBRC-111
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace malfunctioning components.
5.CHECK VDC OFF SW ITCH GROUND CIRCUIT
Check continuity between VDC OFF swit ch connector M72 terminal 2 and ground.
Is the inspection result normal?
YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-128, "Removal and Installa-
tion".
NO >> Repair or replace malfunctioning components.
Component InspectionINFOID:0000000009463828
1.CHECK VDC OFF SWITCH
1. Turn ignition switch OFF.
2. Disconnect VDC OFF switch connector.
3. Check continuity between terminals of VDC OFF switch connector.
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace VDC OFF switch. Refer to BRC-130, "Removal and Installation"
.
ABS actuator and electric unit (control unit)
—Continuity
Connector Terminal
E54 15 Ground No
VDC OFF switch —Continuity
Connector Terminal
M72 2 Ground Yes
VDC OFF switch terminals Condition Continuity
1 – 2 VDC OFF switch pressed Yes
VDC OFF switch released No
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 258 of 4801
![NISSAN TEANA 2014 Service Manual
BRC-112
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
ABS WARNING LAMP
ABS WARNING LAMP
Component Function CheckINFOID:0000000009463829
1.CHECK ABS WARNING LAMP FUNCTION
Check that ABS warning lamp in combi NISSAN TEANA 2014 Service Manual
BRC-112
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
ABS WARNING LAMP
ABS WARNING LAMP
Component Function CheckINFOID:0000000009463829
1.CHECK ABS WARNING LAMP FUNCTION
Check that ABS warning lamp in combi](/manual-img/5/57390/w960_57390-257.png)
BRC-112
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
ABS WARNING LAMP
ABS WARNING LAMP
Component Function CheckINFOID:0000000009463829
1.CHECK ABS WARNING LAMP FUNCTION
Check that ABS warning lamp in combination meter turns ON for approximately 2 seconds after ignition switch
is turned ON.
Is the inspection result normal?
YES >> Inspection End.
NO >> Proceed to diagnosis procedure. Refer to BRC-112, "Diagnosis Procedure"
.
Diagnosis ProcedureINFOID:0000000009463830
1.PERFORM THE SELF-DIAGNOSIS
With CONSULT.
Perform self diagnostic result.
Are any DTCs detected?
YES >> Refer to BRC-45, "DTC Index".
NO >> GO TO 2.
2.CHECK COMBINATION METER
Check if indication and operation of combination meter are normal. Refer to MWI-9, "METER SYSTEM : Sys-
tem Description".
Is the inspection result normal?
YES >> Replace ABS actuator and electr ic unit (control unit). Refer to BRC-128, "Removal and Installa-
tion".
NO >> Replace combination meter. Refer to MWI-82, "Removal and Installation"
.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 259 of 4801
![NISSAN TEANA 2014 Service Manual
BRAKE WARNING LAMPBRC-113
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
BRAKE WARNING LAMP
Component Function CheckINFOID:0000000009463831
1.CHECK BRAKE WARNING LAMP FUN NISSAN TEANA 2014 Service Manual
BRAKE WARNING LAMPBRC-113
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
BRAKE WARNING LAMP
Component Function CheckINFOID:0000000009463831
1.CHECK BRAKE WARNING LAMP FUN](/manual-img/5/57390/w960_57390-258.png)
BRAKE WARNING LAMPBRC-113
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
BRAKE WARNING LAMP
Component Function CheckINFOID:0000000009463831
1.CHECK BRAKE WARNING LAMP FUNCTION (1)
Check that brake warning lamp in combination mete r turns ON for approximately 2 seconds after ignition
switch is turned ON.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Proceed to diagnosis procedure. Refer to BRC-113, "Diagnosis Procedure"
.
2.CHECK BRAKE WARNING LAMP FUNCTION (2)
Check that brake warning lamp in combination meter turns ON/OFF when parking brake is operated.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Check parking brake switch system. Refer to BRC-108, "Diagnosis Procedure"
.
Diagnosis ProcedureINFOID:0000000009463832
1.PERFORM THE SELF-DIAGNOSIS
With CONSULT.
Perform self diagnostic result.
Are any DTCs detected?
YES >> Refer to MWI-27, "DTC Index".
NO >> GO TO 2.
2.CHECK COMBINATION METER
Check if indication and operation of combination meter are normal. Refer to MWI-9, "METER SYSTEM : Sys-
tem Description".
Is the inspection result normal?
YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-128, "Removal and Installa-
tion".
NO >> Replace combination meter. Refer to MWI-82, "Removal and Installation"
.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 260 of 4801
![NISSAN TEANA 2014 Service Manual
BRC-114
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
VDC OFF INDICATOR LAMP
VDC OFF INDICATOR LAMP
DescriptionINFOID:0000000009463833
×
: ON –: OFF
Component Function CheckINFOID:0000000009463834
1.CHEC NISSAN TEANA 2014 Service Manual
BRC-114
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
VDC OFF INDICATOR LAMP
VDC OFF INDICATOR LAMP
DescriptionINFOID:0000000009463833
×
: ON –: OFF
Component Function CheckINFOID:0000000009463834
1.CHEC](/manual-img/5/57390/w960_57390-259.png)
BRC-114
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
VDC OFF INDICATOR LAMP
VDC OFF INDICATOR LAMP
DescriptionINFOID:0000000009463833
×
: ON –: OFF
Component Function CheckINFOID:0000000009463834
1.CHECK VDC OFF INDICA TOR LAMP FUNCTION
Check that VDC OFF indicator lamp in combination meter turns ON for approximately 2 seconds after ignition
switch is turned ON.
Is the inspection result normal?
YES >> Inspection End.
NO >> Proceed to diagnosis procedure. Refer to BRC-114, "Diagnosis Procedure"
.
Diagnosis ProcedureINFOID:0000000009463835
1.PERFORM THE SELF-DIAGNOSIS
With CONSULT.
Perform self diagnostic result.
Are any DTCs detected?
YES >> Refer to BRC-45, "DTC Index".
NO >> GO TO 2.
2.CHECK COMBINATION METER
Check if indication and operation of combination meter are normal. Refer to MWI-9, "METER SYSTEM : Sys-
tem Description".
Is the inspection result normal?
YES >> Replace ABS actuator and electr ic unit (control unit). Refer to BRC-128, "Removal and Installa-
tion".
NO >> Replace combination meter. Refer to MWI-82, "Removal and Installation"
.
Condition VDC OFF indicator lamp
Ignition switch OFF –
For 2 seconds after turning ON ignition switch ×
2 seconds later after turning ON ignition switch –
VDC OFF switch turned ON. (VDC function is OFF.) ×
VDC/TCS function is malfunctioning. –
ABS function is ma lfunctioning. –
EBD function is malfunctioning. –
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 261 of 4801
![NISSAN TEANA 2014 Service Manual
SLIP INDICATOR LAMPBRC-115
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
SLIP INDICATOR LAMP
Component Function CheckINFOID:0000000009463836
1.CHECK SLIP INDICATOR LAMP NISSAN TEANA 2014 Service Manual
SLIP INDICATOR LAMPBRC-115
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
SLIP INDICATOR LAMP
Component Function CheckINFOID:0000000009463836
1.CHECK SLIP INDICATOR LAMP](/manual-img/5/57390/w960_57390-260.png)
SLIP INDICATOR LAMPBRC-115
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
SLIP INDICATOR LAMP
Component Function CheckINFOID:0000000009463836
1.CHECK SLIP INDICATOR LAMP FUNCTION
Check that slip indicator lamp in combination meter turns ON for approximately 2 seconds after ignition switch
is turned ON.
Is the inspection result normal?
YES >> Inspection End.
NO >> Proceed to diagnosis procedure. Refer to BRC-115, "Diagnosis Procedure"
.
Diagnosis ProcedureINFOID:0000000009463837
1.PERFORM THE SELF-DIAGNOSIS
With CONSULT.
Perform self diagnostic result.
Are any DTCs detected?
YES >> Refer to BRC-45, "DTC Index".
NO >> GO TO 2.
2.CHECK COMBINATION METER
Check if indication and operation of combination meter are normal. Refer to MWI-9, "METER SYSTEM : Sys-
tem Description".
Is the inspection result normal?
YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-128, "Removal and Installa-
tion".
NO >> Replace combination meter. Refer to MWI-82, "Removal and Installation"
.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 262 of 4801
![NISSAN TEANA 2014 Service Manual
BRC-116
< SYMPTOM DIAGNOSIS >[VDC/TCS/ABS]
VDC/TCS/ABS
SYMPTOM DIAGNOSIS
VDC/TCS/ABS
Symptom TableINFOID:0000000009463838
If ABS warning lamp and SLIP indicator
lamp turn ON, perform self-diagnosis. NISSAN TEANA 2014 Service Manual
BRC-116
< SYMPTOM DIAGNOSIS >[VDC/TCS/ABS]
VDC/TCS/ABS
SYMPTOM DIAGNOSIS
VDC/TCS/ABS
Symptom TableINFOID:0000000009463838
If ABS warning lamp and SLIP indicator
lamp turn ON, perform self-diagnosis.](/manual-img/5/57390/w960_57390-261.png)
BRC-116
< SYMPTOM DIAGNOSIS >[VDC/TCS/ABS]
VDC/TCS/ABS
SYMPTOM DIAGNOSIS
VDC/TCS/ABS
Symptom TableINFOID:0000000009463838
If ABS warning lamp and SLIP indicator
lamp turn ON, perform self-diagnosis.
NOTE:
• 1: The ABS does not operate when the speed is 10 km/h (6 MPH) or less.
• 2: Under the following conditions, ABS is activated and vibration is felt when brake pedal is lightly depressed (just place a foot on it).
However, this is normal.
- When shifting gears
- When driving on slippery road
- During cornering at high speed
- When passing over bumps or grooves [approximately 50 mm (1.97 in) or more]
- When pulling away just after starting engine [at approximately 10 km/h (6 MPH) or higher] Symptom Check item Reference
Excessive ABS function operation fre-
quency Brake force distribution
BRC-117, "Diagno-
sis Procedure"Looseness of front and rear axle
Wheel sensor and rotor system
Unexpected pedal reaction Brake pedal stroke
BRC-118, "Diagno-
sis Procedure"Make sure the braking force is sufficient when the ABS is not operating.
The braking distance is long Check stopping distance when the ABS is not operating. BRC-119, "Diagno-
sis Procedure"
ABS function does not operate (Note 1) ABS ac
tuator and electric unit (control unit) BRC-120, "Diag-nosis Procedure"
Pedal vibration or ABS operation sound
occurs (Note 2) Brake pedal
BRC-121, "Diag-
nosis Procedure"ABS actuator and electric unit (control unit)
Vehicle jerks duri ng VDC/TCS/ABS con-
trol ABS actuator and electric unit (control unit)
BRC-122, "Diag-
nosis Procedure"TCM
ECM
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 263 of 4801
![NISSAN TEANA 2014 Service Manual
EXCESSIVE ABS FUNCTION OPERATION FREQUENCYBRC-117
< SYMPTOM DIAGNOSIS > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
EXCESSIVE ABS FUNCTION OPERATION FREQUENCY
Diagnosis ProcedureINFOID:0000000 NISSAN TEANA 2014 Service Manual
EXCESSIVE ABS FUNCTION OPERATION FREQUENCYBRC-117
< SYMPTOM DIAGNOSIS > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
EXCESSIVE ABS FUNCTION OPERATION FREQUENCY
Diagnosis ProcedureINFOID:0000000](/manual-img/5/57390/w960_57390-262.png)
EXCESSIVE ABS FUNCTION OPERATION FREQUENCYBRC-117
< SYMPTOM DIAGNOSIS > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
EXCESSIVE ABS FUNCTION OPERATION FREQUENCY
Diagnosis ProcedureINFOID:0000000009463839
1.CHECK START
Check front and rear brake force di stribution using a brake tester.
Is the inspection result normal?
YES >> GO TO 2
NO >> Check brake system.
2.CHECK FRONT AND REAR AXLE
Make sure that there is no excessive play in the front and rear axles. Refer to front: FAX-6, "Inspection"
, rear:
RAX-5, "On-vehicle Service"
.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace malfunctioning components.
3.CHECK WHEEL SENSOR AND SENSOR ROTOR
Check the following:
• Wheel sensor installation for damage
• Sensor rotor installation for damage
• Wheel sensor connector
• Wheel sensor harness
Is the inspection result normal?
YES >> GO TO 4
NO >> • Replace wheel sensor BRC-124, "Removal and Installation - Front Wheel Sensor"
or BRC-125,
"Removal and Installation - Rear Wheel Sensor".
• Replace sensor rotor BRC-127, "Removal and Installation - Front Sensor Rotor"
or BRC-127,
"Removal and Installation - Rear Sensor Rotor".
• Repair harness.
4.CHECK ABS WARNING LAMP DISPLAY
Make sure that the ABS warning lamp is turned off af ter the ignition switch is turned ON or when driving.
Is the inspection result normal?
YES >> Inspection End.
NO >> Perform self diagnostic result. Refer to BRC-33, "CONSULT Function (ABS)"
.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 264 of 4801
BRC-118
< SYMPTOM DIAGNOSIS >[VDC/TCS/ABS]
UNEXPECTED PEDAL REACTION
UNEXPECTED PEDAL REACTION
Diagnosis ProcedureINFOID:0000000009463840
1.CHECK BRAKE PEDAL STROKE
Check brake pedal stroke. Refer to BR-13, "Inspection and Adjustment"
.
Is the stroke too big?
YES >> • Bleed air from brake line and hose. Refer to BR-14, "Bleeding Brake System".
• Check brake pedal, brake booster, and master cylinder for mount play, looseness, brake system fluid leakage, etc. Refer to brake pedal: BR-13, "Inspection and Adjustment"
or brake booster
assembly BR-10, "Inspection"
.
NO >> GO TO 2
2.CHECK ABS FUNCTION
1. Disconnect ABS actuator and electric unit (control unit) connector to deactivate ABS.
2. Check if braking force is normal in this condition.
3. Reconnect connector after inspection.
Is the inspection result normal?
YES >> Inspection End.
NO >> Check brake system.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM