Page 4785 of 4801
WW-50
< SYMPTOM DIAGNOSIS >
NORMAL OPERATING CONDITION
NORMAL OPERATING CONDITION
DescriptionINFOID:0000000009464627
FRONT WIPER MOTOR PROTECTION FUNCTION
• IPDM E/R may stop the front wiper to protect the front wiper motor if any obstruction (operation resistance)
such as a large amount of snow is detected during the front wiper operation.
• At that time turn OFF the front wiper and remove t he foreign object. Then wait for approximately 20 seconds
or more and reactivate the front wiper. The wiper will operate normally.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 4786 of 4801

WASHER TANKWW-51
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
K
M A
B
WW
N
O P
REMOVAL AND INSTALLATION
WASHER TANK
Exploded ViewINFOID:0000000009464628
Removal and InstallationINFOID:0000000009464629
REMOVAL
1. Drain the washer fluid.
2. Remove the front under cover. Refer to EXT-28, "Removal and Installation"
.
3. Remove the fender protector (RH). Refer to EXT-26, "FENDER PROTECTOR : Removal and Installation"
.
4. Disconnect the harness connectors from the washer pump and washer level switch.
5. Disconnect the front washer tube from the washer pump.
6. Disconnect the rear washer tube from the washer pump (if equipped).
7. Remove the washer tank bolts, then remove the washer tank.
8. Remove the washer pump, washer level switch, and wa sher tank seals from the washer tank (if neces-
sary).
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
• After installation, add water to the top of the washer tank inlet to check that no leaks exist.
• Fill washer tank with specified amount of fluid. Refer to WW-66, "Specifications"
.
1. Washer tank 2. Washer level switch 3. Washer tank seal
4. Washer pump (without rear washer tube) 5. Washer pump (with rear washer tube) 6. Washer tank inlet
AWLIA2228ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 4787 of 4801

WW-52
< REMOVAL AND INSTALLATION >
WASHER PUMP
WASHER PUMP
Exploded ViewINFOID:0000000009464630
Removal and InstallationINFOID:0000000009464631
REMOVAL
1. Drain the washer fluid.
2. Remove the front under cover. Refer to EXT-28, "Removal and Installation"
.
3. Remove the fender protector (RH). Refer to EXT-26, "FENDER PROTECTOR : Removal and Installation"
.
4. Disconnect the harness connecto r from the washer pump.
5. Disconnect the front washer tube from the washer pump.
6. Disconnect the rear washer tube from the washer pump (if equipped).
7. Remove the washer pump.
8. Remove the washer tank seal (if necessary).
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
• After installation, add water to the top of the washer tank inlet to check that no leaks exist.
• Fill washer tank with specified amount of fluid. Refer to WW-66, "Specifications"
.
1. Washer tank 2. Washer level switch 3. Washer tank seal
4. Washer pump (without rear washer tube) 5. Washer pump (with rear washer tube) 6. Washer tank inlet
AWLIA2228ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 4788 of 4801

WASHER LEVEL SWITCHWW-53
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
K
M A
B
WW
N
O P
WASHER LEVEL SWITCH
Exploded ViewINFOID:0000000009464632
Removal and InstallationINFOID:0000000009464633
REMOVAL
1. Drain the washer fluid.
2. Remove the front under cover. Refer to EXT-28, "Removal and Installation"
.
3. Remove the fender protector (RH). Refer to EXT-26, "FENDER PROTECTOR : Removal and Installation"
.
4. Disconnect the harness connector from the washer level switch.
5. Remove the washer level switch.
6. Remove the washer tank seal (if necessary).
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
• After installation, add water to the top of the washer tank inlet to check that no leaks exist.
• Fill washer tank with specified amount of fluid. Refer to WW-66, "Specifications"
.
1. Washer tank 2. Washer level switch 3. Washer tank seal
4. Washer pump (without rear washer tube) 5. Washer pump (with rear washer tube) 6. Washer tank inlet
AWLIA2228ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 4789 of 4801
WW-54
< REMOVAL AND INSTALLATION >
WASHER NOZZLE & TUBE
WASHER NOZZLE & TUBE
Exploded ViewINFOID:0000000009464634
FRONT
REAR (IF EQUIPPED)
ALLIA1162ZZ
1. Front washer tube 2. Washer tank 3. Washer pump
4. Washer nozzle Front
ALLIA1331ZZ
1. Rear washer tube
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 4790 of 4801
WASHER NOZZLE & TUBEWW-55
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
K
M A
B
WW
N
O P
WASHER NOZZLE
WASHER NOZZLE : Removal and InstallationINFOID:0000000009464635
REMOVAL
1. Disconnect the washer tube from the washer nozzle.
2. Disconnect the washer nozzle from the hood by pushing on the pawl in the direction shown (A).
: Pawl
3. Remove the washer nozzle.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Adjust the nozzle spray pattern. Refer to WW-55, "WASHER NOZZLE : Adjustment"
.
WASHER NOZZLE : AdjustmentINFOID:0000000009464636
ALLIA1163ZZ
A. 553.3 mm (21.8 in) B. 77.8 mm (3.1 in) C. 163.2 mm (6.4 in)
D. 272.6 mm (10.7 in) E. 393 mm (15.5 in) F. 54.2 mm (2.1 in)
ALLIA1164ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 4791 of 4801
WW-56
< REMOVAL AND INSTALLATION >
WASHER NOZZLE & TUBE
NOTE:
Spray positions for LH shown; RH is symmetrical.
Insert a suitable tool (A) into the nozzle hole (B) and move up/down
and left/right to adjust the spray position of each nozzle (1).
WASHER TUBE
WASHER TUBE : Removal and InstallationINFOID:0000000009464637
FRONT WASHER TUBE
Removal
1. Drain the washer fluid.
2. Remove the hood ledge finisher clips and the hood ledge fin- isher (1) (RH).
: Clip
G. 71.1 mm (2.8 in) H. 141 mm (5.6 in) J. 500.2 mm (19.7 in)
K. 505.5 mm (19.9 in)
1. Washer Nozzle (LH) 2. Washer Nozzle (RH) A. 60°± 7.5 °
B. 6 ° C. 1.5°± 1.0 ° D. 4°
ALLIA1165ZZ
ALLIA0779ZZ
ALLIA1174ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 4792 of 4801

WASHER NOZZLE & TUBEWW-57
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
K
M A
B
WW
N
O P
3. Remove the hood insulator. Refer to DLK-170, "HOOD ASSEMBLY : Exploded View".
4. Disconnect the washer tube from the washer nozzles (LH/RH).
5. Remove the front under cover. Refer to EXT-28, "Removal and Installation"
.
6. Remove the fender protector (RH). Refer to EXT-26, "FENDER PROTECTOR : Removal and Installation"
.
7. Disconnect the washer tube from the washer pump.
8. Remove the washer tube.
Installation
Installation is in the reverse order of removal.
NOTE:
Fill washer tank with specified amount of fluid. Refer to WW-66, "Specifications"
.
REAR WASHER TUBE (IF EQUIPPED)
Removal
1. Drain the washer fluid.
2. Remove trunk lid finisher. Refer to INT-33, "TRUNK LID FINISHER : Removal and Installation"
.
3. Disconnect the rear washer tube (1 ) from rear view camera (2).
4. Remove rear seat bolster (RH). Refer to SE-38, "Removal and Installation - Rear Seat Bolster"
.
5. Remove seatback latch finisher. Refer to INT-26, "Exploded View"
.
6. Remove rear kicking plate inner (RH). Refer to INT-22, "REAR KICKING PLATE : Removal and Installa-
tion - Inner".
7. Remove center pillar lower finisher (RH). Refer to INT-23, "CENTER PILLAR LOWER FINISHER :
Removal and Installation".
8. Remove front kicking plate inner (RH). Refer to INT-21, "FRONT KICKING PLATE : Removal and Installa-
tion - Inner".
9. Remove dash side finisher (RH). Refer to INT-20, "DASH SIDE FINISHER : Removal and Installation"
.
10. Remove fender protector (RH). Refer to EXT-26, "FENDER PROTECTOR : Removal and Installation"
.
11. Disconnect the rear washer tube from the washer pump.
12. Remove rear washer tube.
Installation
Installation is in the reverse order of removal.
NOTE:
Fill washer tank with specified amount of fluid. Refer to WW-66, "Specifications"
.
ALOIA0202ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM