2014 NISSAN TEANA Service Manual

dashboard warning lights dashboard height fuse box diagram engine navigation system

Page 4313 of 4801

NISSAN TEANA 2014 Service Manual
TM-98
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F10D]
P0705 TRANSMISSION
RANGE SENSOR A
3. Turn ignition switch ON.
4. Shift the selector lever from “P” to “DS” and check voltage between TCM harne

TM-98
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F10D]
P0705 TRANSMISSION
RANGE SENSOR A
3. Turn ignition switch ON.
4. Shift the selector lever from “P” to “DS” and check voltage between TCM harness connector terminals and
ground.
Is the inspection result normal?
YES >> Check intermitt ent incident. Refer to GI-43, "Intermittent Incident".
NO-1 [“D POSITION SW” is “ON” when selector is not in “D” position. (Or connector terminal 4 is at power
voltage.)]>>GO TO 2.
NO-2 [“N POSITION SW” is “ON” when selector is not in “N” position. (Or connector terminal 5 is at power
voltage.)]>>GO TO 4.
NO-3 [“R POSITION SW” is “ON” when selector is not in “R” position. (Or connector terminal 6 is at power
voltage.)]>>GO TO 6.
NO-4 [“P POSITION SW” is “ON” when selector is not in “P” position. (Or connector terminal 7 is at power
voltage.)]>>GO TO 8.
NO-5 [“DS POSITION SW” is “ON” w hen selector is not in “DS” position. (Or connector terminal 2 is at power
voltage.)]>>GO TO 10.
2.CHECK D POSITION SW CIRCUIT (PART 1)
1. Turn ignition switch OFF.
2. Disconnect TCM connector.
3. Check continuity between TCM harness connector terminals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace malfunctioning parts.
3.CHECK D POSITION SW CIRCUIT (PART 2)
1. Disconnect transmission range switch connector.
2. Turn ignition switch ON.
3. Check voltage between TCM harness connector terminal and ground.
+
−Test condition Voltage
TCM
Connector Terminal
F16 2
Ground Selector lever: “ DS” position 10 – 16 V
Other than the above Approx. 0 V
4 Selector lever: “D” position 10 – 16 V
Other than the above Approx. 0 V
5 Selector lever: “N” position 10 – 16 V
Other than the above Approx. 0 V
6 Selector lever: “R” position 10 – 16 V
Other than the above Approx. 0 V
7 Selector lever: “P” position 10 – 16 V
Other than the above Approx. 0 V
TCM Continuity
Connector Terminal
F16 4 2
Not existed
5
6
7
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

Page 4314 of 4801

NISSAN TEANA 2014 Service Manual
P0705 TRANSMISSION RANGE SENSOR ATM-99
< DTC/CIRCUIT DIAGNOSIS > [CVT: RE0F10D]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
Is the inspection result normal?
YES >> GO TO 12.
NO >> Repair or replace malfunction

Page 4315 of 4801

NISSAN TEANA 2014 Service Manual
TM-100
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F10D]
P0705 TRANSMISSION
RANGE SENSOR A
7.CHECK P POSITION SW CIRCUIT (PART 2)
1. Disconnect transmission range switch connector.
2. Turn ignition switch ON

Page 4316 of 4801

NISSAN TEANA 2014 Service Manual
P0705 TRANSMISSION RANGE SENSOR ATM-101
< DTC/CIRCUIT DIAGNOSIS > [CVT: RE0F10D]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
Is the inspection result normal?
YES >> GO TO 11.
NO >> Repair or replace malfunctio

Page 4317 of 4801

NISSAN TEANA 2014 Service Manual
TM-102
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F10D]
P0705 TRANSMISSION
RANGE SENSOR A
YES >> INSPECTION END
NO >> There is a malfunction of transmission range switch. Replace transaxle assembly. Refer t

Page 4318 of 4801

NISSAN TEANA 2014 Service Manual
P0706 TRANSMISSION RANGE SENSOR ATM-103
< DTC/CIRCUIT DIAGNOSIS > [CVT: RE0F10D]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
P0706 TRANSMISSION RANGE SENSOR A
DTC LogicINFOID:0000000009464042
DTC DETECTION LOGI

P0706 TRANSMISSION RANGE SENSOR ATM-103
< DTC/CIRCUIT DIAGNOSIS > [CVT: RE0F10D]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
P0706 TRANSMISSION RANGE SENSOR A
DTC LogicINFOID:0000000009464042
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Shift the selector lever through entire positions from “P” to “DS”. (Hold the selector lever at each position
for 40 seconds or more.)
3. Check the first trip DTC.
Is
“P0706” detected?
YES >> Go to TM-103, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000009464043
1.ADJUSTMENT OF CONTROL CABLE
Adjust control cable. Refer to TM-180, "Inspection"
.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1. Turn ignition switch ON.
2. Select “Self Diagnostic Results” in “TRANSMISSION”.
3. Touch “Erase”.
4. Perform “DTC CONFIRMATION PROCEDURE". Refer to TM-103, "DTC Logic"
.
Is
“P0706” detected?
YES >> GO TO 3.
NO >> INSPECTION END
3.CHECK POWER CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect transmission range switch connector.
3. Turn ignition switch ON.
4. Check voltage between transmission range switch harness connector terminal and ground.
DTC CONSULT screen terms
(Trouble diagnosis content) DTC detection condition Possible causes
P0706 T/M RANGE SENSOR A
(Transmission Range Sensor
A Circuit Range/Performance) When all of the following conditions are satis-
fied and this state is maintained for 30 sec-
onds:
• All range signals stay OFF
• TCM power supply voltage: More than 11 V • Harness or connector
(Open circuit between ignition switch
and transmission range switch/open
circuit between transmission range
switch and TCM)
• Transmission range switch
• Control cable
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

Page 4319 of 4801

NISSAN TEANA 2014 Service Manual
TM-104
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F10D]
P0706 TRANSMISSION
RANGE SENSOR A
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 7.
4.CHECK CIRCUIT BETWEEN TRANSMISSION RANGE SWITCH A

Page 4320 of 4801

NISSAN TEANA 2014 Service Manual
P0706 TRANSMISSION RANGE SENSOR ATM-105
< DTC/CIRCUIT DIAGNOSIS > [CVT: RE0F10D]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
Is the check result normal?
YES >> GO TO 8.
NO >> Repair or replace malfunctioning p

Load next 8 pages

Page: < prev 1-10 ... 4281-4288 4289-4296 4297-4304 4305-4312 4313-4320 4321-4328 4329-4336 4337-4344 4345-4352 ... 4808 next >

cooling engine oil carplay gas type air suspension checking oil