2014 NISSAN TEANA Service Manual

airbag disable steering wheel check transmission fluid windshield wipers clock reset key

Page 1097 of 4801

NISSAN TEANA 2014 Service Manual
ECM
EC-97
< ECU DIAGNOSIS INFORMATION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O50
(L) 128
(GR) Intake manifold runner
control valve motor power
supply Input [Ignition switch: ON]
Battery voltag

ECM
EC-97
< ECU DIAGNOSIS INFORMATION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O50
(L) 128
(GR) Intake manifold runner
control valve motor power
supply Input [Ignition switch: ON]
Battery voltage
(11 - 14 V)
51
(B) 128
(GR) Intake manifold runner
control valve motor
(Open) Output[Ignition switch ON]
• Engine coolant temperature: Be- tween -12 °C (10 °F) and 59 °C
(138 °F)
• Accelerator pedal: Fully released →
depressed Battery voltage appears for about
1 second.
52
(B) — ECM ground — — —
53
(BR) 128
(GR) A/F sensor 1 heater Input [Engine is running]
• Warm-up condition
• Idle speed
(More than 140 seconds after start-
ing engine) 2.9 - 8.8 V
54
(Y) 128
(GR) Heated oxygen sensor 2
heater Output[Engine is running]
• Engine speed: Below 3,600 rpm af-
ter the following conditions are met
- Engine: after warming up
- Keeping the engine speed between
3,500 and 4,000 rpm for 1 minute
and at idle for 1 minute under no
load 10 V
[Ignition switch: ON]
• Engine stopped
[Engine is running]
• Engine speed: Above 3,600 rpm Battery voltage
(11 - 14 V)
56
(SB) 128
(GR) Intake valve timing inter-
mediate lock control sole-
noid valve Output[Engine is running]
• Warm-up condition
• Idle speed 0 V
[Engine is running]
• Cold condition [Engine coolant tem- perature: below 60 °C (140 °F)]
• Idle speed Battery voltage
(11 - 14 V)
58
*1
(L) —Sensor ground
[Manifold absolute pres-
sure (MAP) sensor] —— —
59
*1
(LG) 58
*1
(L)Manifold absolute pres-
sure (MAP) sensor Output[Engine is running]
• Warm-up condition
• Both A/C switch and blower fan switch: ON (Compressor operates) 4.6 V
Output voltage atmospheric pressure.
[Engine is running]
• Warm-up condition
• Idle speed 1.2 V
[Engine is running]
• Warm-up condition
• Engine speed: 2,000 rpm 1.5 V
60
*1
(V) —Sensor power supply
[Manifold absolute pres-
sure (MAP) sensor] — [Ignition switch: ON] 5.0 V
Terminal No.
(Wire color) Description
ConditionVa l u e
(Approx.)
+ − Signal name Input/
Output
JPBIA4732ZZ
JMBIA0325GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

Page 1098 of 4801

NISSAN TEANA 2014 Service Manual
EC-98
< ECU DIAGNOSIS INFORMATION >[QR25DE]
ECM
61
(W) 62
(R) Battery temperature sen-
sor Input[Engine is running]
• Battery temperature: 25 °C ( °F)
• Idle speed 3.3 V
62
(R) —Sensor groun

Page 1099 of 4801

NISSAN TEANA 2014 Service Manual
ECM
EC-99
< ECU DIAGNOSIS INFORMATION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
79
(W) 78
(B) Throttle position sensor 1 Input [Ignition switch: ON]
• Engine stopped
• Selector lever: D
•

Page 1100 of 4801

NISSAN TEANA 2014 Service Manual
EC-100
< ECU DIAGNOSIS INFORMATION >[QR25DE]
ECM
93
(Y) 128
(GR) Intake valve timing control
solenoid valve Output[Engine is running]
• Warm-up condition
• Idle speed 0 V
[Engine is running]
�

Page 1101 of 4801

NISSAN TEANA 2014 Service Manual
ECM
EC-101
< ECU DIAGNOSIS INFORMATION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
*1: For California
*2: B

ECM
EC-101
< ECU DIAGNOSIS INFORMATION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
*1: For California
*2: Before measuring the terminal voltage, confi rm that the battery is fully charged. Refer to PG-4, "How to
Handle Battery".
Fail SafeINFOID:0000000009462122
NON DTC RELATED ITEM
11 5
(L) 128
(GR) Stop lamp switch Input [Ignition switch: OFF]
• Brake pedal: Fully released 0 V
[Ignition switch: OFF]
• Brake pedal: Slightly depressed Battery voltage
(11 - 14 V)
11 6
(BR) 128
(GR) Brake pedal position
switch Input[Ignition switch: OFF]
• Brake pedal: Fully released Battery voltage
(11 - 14 V)
11 7
(W) 128
(GR) PNP signal Input [Ignition switch: ON]
• Selector lever: P or N Battery voltage
(11 - 14 V)
[Ignition switch: ON]
• Selector lever: Except above 0 V
11 8 (G) —Sensor power supply
(Accelerator pedal posi-
tion sensor 2) — [Ignition switch: ON] 5.0 V
11 9 (P) 120
(G) Accelerator pedal posi-
tion sensor 2 Input[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully released 0.25 - 0.5 V
[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully depressed 2.0 - 2.5 V
120 (G) —Sensor ground
(Accelerator pedal posi-
tion sensor 2) —— —
121
(LG) 128
(GR) Power supply for ECM Input [Ignition switch: ON] Battery voltage
(11 - 14 V)
122 (V) —Sensor power supply
(Accelerator pedal posi-
tion sensor 1) — [Ignition switch: ON] 5.0 V
124
(SB) —Sensor ground
(EVAP control system
pressure sensor, refriger-
ant pressure sensor) —— —
125
(BR) 128
(GR) Fuel tank temperature
sensor Input [Engine is running] 0 - 4.8 V
Output voltage varies with fuel tank temperature
126
(SB) 127
(L) Accelerator pedal posi-
tion sensor 1 Input[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully released 0.5 - 1.0 V
[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully depressed 4.2 - 4.8 V
127 (L) —Sensor ground
(Accelerator pedal posi-
tion sensor 1) —— —
128
(GR) — ECM ground — — —
Terminal No.
(Wire color) Description
ConditionVa l u e
(Approx.)
+ − Signal name Input/
Output
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

Page 1102 of 4801

NISSAN TEANA 2014 Service Manual
EC-102
< ECU DIAGNOSIS INFORMATION >[QR25DE]
ECM
DTC RELATED ITEM
Description
When a DTC is detected, ECM executes a mode (in the
Fail-safe mode) applicable to the DTC. The fail-safe
mode has the pr

EC-102
< ECU DIAGNOSIS INFORMATION >[QR25DE]
ECM
DTC RELATED ITEM
Description
When a DTC is detected, ECM executes a mode (in the
Fail-safe mode) applicable to the DTC. The fail-safe
mode has the preset traveling control mode (acceler ator angle variation and engine output limit) and device fix
mode.
Fail Safe Pattern
Fail Safe List
× :Applicable —: Not applicable
Detected
items Engine operating condition
in fail-safe mode Remarks Reference page
Malfunction
indicator
lamp circuit Engine speed will not rise
more than 2,500 rpm due
to the fuel cut When there is an open circuit on MIL circuit, the ECM cannot warn the
driver by lighting up MIL when there is malfunction on engine control
system.
Therefore, when electrical controlled throttle and part of ECM related
diagnoses are continuously detected as NG for 5 trips, ECM warns the
driver that engine control system malfunctions and MIL circuit is open
by means of operating fail safe function.
The fail safe function also operates when above diagnoses except MIL
circuit are detected and demands the driver to repair the malfunction. EC-517, "Compo-
nent Function
Check"
Fail safe mode Vehicle behavior
Traveling con-
trol mode Accelerator an-
gle variation
control ECM controls the accelerator pedal depression speed to make it slower than actual speed. This
causes a drop in accelerating performance and encourages the driver to repair malfunction.
NOTE:
ECM does not control the accelerator pedal releasing speed.
Engine output
control ECM reduces the engine output, according to the rise in engine speed. This reduces the vehicle
speed to encourage the driver to repair malfunction.
Device fix mode • This mode fixes the IVT control solenoid valve and the EVT control solenoid valve in the refer-
ence position.
• The intake manifold runner control valve motor is turned OFF (intake manifold runner control
valve opens).
Pattern Fail safe mode
A Traveling control mode Accelerator angle variation control
B Engine output control
C Device fix mode
DTC No. Detected items Vehicle behavior
Pattern Others
ABC
P0011 Intake valve timing control ——×ECM activates the IVT intermediate lock control solenoid
valve to bring the cam sprocket into an intermediate lock con-
dition.
P0014
P0078 Exhaust valve timing control
——× —
P0101
P0102
P0103 Mass air flow sensor circuit
××× —
P0122
P0123
P0222
P0223
P2135 Throttle position sensor
———The ECM controls the electric throttle control actuator in reg-
ulating the throttle opening in order for the idle position to be
within +10 degrees.
The ECM regulates the opening speed of the throttle valve to
be slower than the normal condition.
So, the acceleration will be poor.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

Page 1103 of 4801

NISSAN TEANA 2014 Service Manual
ECM
EC-103
< ECU DIAGNOSIS INFORMATION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
OP0171
P0172 Fuel injection system
×—— —
P0197
P0198 Engine oil temperature sensor
———Exhaust valve tim

ECM
EC-103
< ECU DIAGNOSIS INFORMATION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
OP0171
P0172 Fuel injection system
×—— —
P0197
P0198 Engine oil temperature sensor
———Exhaust valve timing control does not function.
P0300
P0301
P0302
P0303
P0304 Misfire
×—— —
P0500 Vehicle speed sensor ×—— —
P050A Cold start control ×—— —
P0524 Engine oil pressure
———• ECM illuminates oil pressure warning lamp on the combina-
tion meter.
• Engine speed will not rise more than 4,000rpm due to the fuel cut.
• Fail-safe is canceled when ignition switch OFF → ON.
P052A
P052B Intake valve timing intermedi-
ate lock control ——
× —
P0603 ECM power supply circuit — ×——
P0605 ECM — ×——
P0643 Sensor power supply ———ECM stops the electric throttle control actuator control, throttle
valve is maintained at a fixed opening (approx. 5 degrees) by
the return spring.
P1078 Exhaust valve timing control position sensor circuit ×
— × —
P1805 Brake switch
———ECM controls the electric throttle control actuator by regulat-
ing the throttle opening to a small range.
Therefore, acceleration will be poor.
Vehicle condition Driving condition
When engine is idling Normal When accelerating Poor acceleration
P2004 Intake manifold runner control valve —
×× —
P2100
P2103 Throttle contro
l motor relay
——— ECM stops the electric throttle control actuator control, throttle
valve is maintained at a fixed opening (approx. 5 degrees) by
the return spring.
P2101 Electric throttle control func- tion ——— ECM stops the electric throttle control actuator control, throttle
valve is maintained at a fixed opening (approx. 5 degrees) by
the return spring.
P2118 Throttle control motor ———ECM stops the electric throttle control actuator control, throttle
valve is maintained at a fixed opening (approx. 5 degrees) by
the return spring.
P2119 Electric thro ttle control actua-
tor —
×——
P2122
P2123
P2127
P2128
P2138 Accelerator pedal position
sensor
———The ECM controls the electric throttle control actuator in reg-
ulating the throttle opening in order for the idle position to be
within +10 degrees.
The ECM regulates the opening speed of the throttle valve to
be slower than the normal condition.
So, the acceleration will be poor.
DTC
No. Detected items Vehicle behavior
Pattern Others
ABC
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

Page 1104 of 4801

NISSAN TEANA 2014 Service Manual
EC-104
< ECU DIAGNOSIS INFORMATION >[QR25DE]
ECM
DTC Inspection Priority Chart
INFOID:0000000009462123
If some DTCs are displayed at the same time, perfo rm inspections one by one based on the follow

Load next 8 pages

Page: < prev 1-10 ... 1065-1072 1073-1080 1081-1088 1089-1096 1097-1104 1105-1112 1113-1120 1121-1128 1129-1136 ... 4808 next >

remote start maintenance schedule tires dead battery open hood timing belt