Page 1553 of 5135
I34726
Radio Receiver Assy
FL±
FL+
FR±
FR+6
12
5 R4
R4
R4
R4LG (*1)
R (*1)
R (*2)
W (*2)Navigation ECU
10
N3
N31AUI±
AUI+
11
N3
N32AUO±
AUO+ F21
Front No.1
Speaker Assy LH
F22
Front No.1
Speaker Assy RH2
1
LG1 LT16
Tweeter Front LH
(±) IN
(+) OUT(+) IN (±) OUT
2
34V
P6
IA1
IA1
IL1
IL1V (*1)
P (*1)
2
1
P1 VT17
Tweeter Front RH
(±) IN
(+) OUT(+) IN (±) OUT
2
34LGL61
1
LG (*2) L (*2)
*1: LHD
*2: RHD
± DIAGNOSTICSNAVIGATION SYSTEM
05±1479
AVENSIS REPAIR MANUAL (RM1018E)
FRONT SPEAKER (DRIVER SIDE) ONLY IS NOT HEARD
WIRING DIAGRAM
05C3N±01
Page 1554 of 5135

I35667
AUI+
AUI±
FL± FL+
FR±FR+
Navigation ECU:
Radio Receiver Assy:
N3
R4
05±1480
± DIAGNOSTICSNAVIGATION SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
INSPECTION PROCEDURE
1 CHECK SETTING(THE VOLUME OF THE NAVIGATION VOICE SOUND)
(a) Check the settings.
(1) Set the volume MAX at the voice sound settings on the menu.
Standard: ºThis system will guide you in this volumeº is produced.
OK Go to step 4
NG
2 CHECK HARNESS AND CONNECTOR(NAVIGATION ECU ± RADIO RECEIVER
ASSY)
(a) Disconnect the connector between the navigation ECU
and radio receiver assy.
(1) Check continuity between the terminals at each
condition, as shown in the chart.
Standard:
Tester connectionSpecified condition
FL+*1, FR+*2 ± AUI+Continuity
FL±*1, FR±*2 ± AUI±Continuity
*1: LHD Models
*2: RHD Models
(2) Check for a short between the terminals at each
condition, as shown in the chart.
Standard:
Tester connectionSpecified condition
AUI+ ± Body groundNo continuity
AUI± ± Body groundNo continuity
NG REPAIR OR REPLACE HARNESS OR
CONNECTOR
OK
Page 1555 of 5135
I35668
FL+FR+
FR±FL±
R4
±
DIAGNOSTICS NAVIGATION SYSTEM
05±1481
AVENSIS REPAIR MANUAL (RM1018E)
3INSPECT RADIO RECEIVER ASSY(FL+(*1), FL±(*1), FR+(*2), FR±(*2), \
GND)
(a)Remove the radio receiver assy.
(b)Using an oscilloscope, check the signal waveform be-
tween the terminals FL+*
1, FL±*1, FR+*2, FR±*2 and GND
of stereo component amplifier assy.
*1: LHD Models
*2: RHD Models
Standard:
Tester connectionConditionSpecified condition
FL+*1, FR+*2 ± GNDWhile voice sound is being producedA waveform synchronized with sound is output
FL±*1, FL±*2 ±GNDWhile voice sound is being producedA waveform synchronized with sound is output
NGREPLACE RADIO RECEIVER ASSY (See page 67±5)
OK
4 INSPECT FRONT NO.1 SPEAKER ASSY
(a) Resistance check (1) Check resistance between the terminals of the front No.1 speaker assy.
Standard: 4
NOTICE:
The speaker should not be removed for checking
NG REPLACE FRONT NO.1 SPEAKER ASSY (See page 67±10)
OK
Page 1556 of 5135
I33631
Navigation ECU:
Front No. 1 Speaker Assy LH:AUO+
AUO±
N3
Front No. 1 Speaker Assy RH:
F21
F22
05±1482
±
DIAGNOSTICS NAVIGATION SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
5CHECK HARNESS AND CONNECTOR(NAVIGATION ECU ± FRONT NO. 1 SPEAKER ASSY)
(a)Disconnect the connectors from the navigation ECU and
front No.1 speaker assy.
(1)Check continuity between the terminals at eachcondition, as shown in the chart.
Standard:
Tester connectionSpecified condition
AUO+ ± 1Continuity
AUO± ± 2Continuity
(2)Check for a short between the terminals at each condition, as shown in the chart.
Standard:
Tester connectionSpecified condition
AUO+ ± Body groundNo continuity
AUO± ± Body groundNo continuity
NGREPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE NAVIGATION ECU (See page 67±27)
Page 1557 of 5135
05C88±01
B70813
Unlock Warning
Switch Assy
Instrument Panel J/B Assy
Integration Relay
Door Fuse
Unlock Warning
Switch Assy
LHD Models
RHD ModelsCenter J/B
Center J/B
Fuse Block Assy
ECU±B 2 Fuse
Instrument Panel J/B Assy
Integration Relay
Door FuseFuse Block Assy
ECU±B 2 Fuse 05±1540
± DIAGNOSTICSPOWER DOOR LOCK CONTROL SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
LOCATION
Page 1558 of 5135
B70496
Front Door w/ Motor
Lock Assy LH
Front Door Courtesy
Lamp Switch Assy
Rear Door w/ Motor
Lock Assy LH
Rear Door Courtesy
Lamp Switch AssyFront Door Courtesy
Lamp Switch Assy
Rear Door w/ Motor
Lock Assy RH
Rear Door Courtesy
Lamp Switch Assy Front Door w/ Motor
Lock Assy RH
Sedan Models
Wagon Models Liftback Models
Back Door Lock Assy Power Window Regulator Master Switch Assy
Door Control SwitchBack Door Lock Assy
Back Door Opener Switch Assy
(Outside Handle Switch)
Back Door Lock Assy
Back Door Opener Switch Assy
(Outside Handle Switch)Back Door Opener Switch Assy
(Outside Handle Switch)
± DIAGNOSTICSPOWER DOOR LOCK CONTROL SYSTEM
05±1541
AVENSIS REPAIR MANUAL (RM1018E)
Page 1559 of 5135
05C87±01
± DIAGNOSTICSPOWER DOOR LOCK CONTROL SYSTEM
05±1539
AVENSIS REPAIR MANUAL (RM1018E)
CUSTOMIZE PARAMETERS
HINT:
The following items can be customized.
NOTICE:
After confirming whether the items requested by the customer are applicable or not for custo-
mization, perform the customize operation.
Be sure to record the current settings before customizing.
When troubleshooting, make sure that the item in question is not set to ºOFFº as a result of
customization.
Standard (Integration relay):
DISPLAY (ITEM)DEFAULTCONTENTSSETTING
AUTO LOCK DELAY30sFunction that selects AUTO LOCK time 30 sec. or 60 sec.30s/60s
ALL UNLK/OPN±CL
(All unlock w/ D door open±close)OFFFunction that unlocks all other doors when opening driver side door within
10 seconds after turning the ignition switch to OFF from ONON/OFF
Page 1560 of 5135

05C86±01
B50154
12 345 67 8
9 11121314 151610
DLC3
A82518
Hand±held Tester
05±1536
± DIAGNOSTICSPOWER DOOR LOCK CONTROL SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
PRE±CHECK
1. DIAGNOSIS SYSTEM
(a) Inspect the DLC3.
HINT:
The vehicle's ECM uses the ISO 14230 (M±OBD) communica-
tion protocol. The terminal arrangement of DLC3 complies with
ISO 15031±03 and matches the ISO 14230 format.
Tester ConnectionConditionSpecified Condition
7 (Bus + line) ± 5 (Signal ground)During communicationPulse generation
4 (Chassis ground) ± Body groundConstantBelow 1
5 (Signal ground) ± Body groundConstantBelow 1
16 (B+) ± Body groundConstant9 to 14 V
HINT:
If the display shows UNABLE TO CONNECT TO VEHICLE when you have connected the cable of the hand±
held tester to the DLC3, turned the ignition switch ON and used the hand±held tester, there is a problem on
the vehicle side or tester side.
If communication is normal when the tester is connected to another vehicle, inspect the DLC3 of the
original vehicle.
If communication is still impossible when the tester is connected to another vehicle, the problem is
probably in the tester itself, so consult the Service Department listed in the tester's manual.
(b) Check the battery voltage.
Battery voltage: 11 to 14 V
If voltage is below 11V, recharge the battery before proceeding.
2. USING HAND±HELD TESTER
(a) Connect the hand±held tester to the DLC3.
(b) Monitor the ECU data by following the prompts on the tes-
ter screen.
HINT:
The hand±held tester has a ºSnapshotº function which records
the monitored data.
Refer to the hand±held tester operator's manual for further de-
tails.