2005 TOYOTA AVENSIS Service Repair Manual

brake rotor ECU fog light bulb oil filter brake sensor low beam

Page 945 of 5135

TOYOTA AVENSIS 2005 Service Repair Manual 05±924± DIAGNOSTICSELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U241E(1AZ±FSE))
AVENSIS REPAIR MANUAL (RM1018E)ItemDiagnostic Note Normal Condition Measurement Item/
Display (Range)
PNP SW [N

05±924± DIAGNOSTICSELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U241E(1AZ±FSE))
AVENSIS REPAIR MANUAL (RM1018E)ItemDiagnostic Note Normal Condition Measurement Item/
Display (Range)
PNP SW [NSW]PNP SW Status/
ON or OFFShift lever range is;
P or N: ON
Except P or N: OFF
The shift lever range and these
REVERSEPNP SW Status/
ON or OFFShift lever range is;
R: ON
Except R: OFFThe shift lever range and these
values are different, there are fail-
ures of the PNP switch or shift
cable adjustment
DRIVEPNP SW Status/
ON or OFFShift lever range is;
D and 3: ON
Except D and 3: OFFcable adjustment.
SOLENOID (SLT)Shift Solenoid SLT Status/
ON or OFFIG SW ON: ON
AT FLUID TEMP
ATF Temp. Sensor Value/
min.: ±40C (±40F)
max.: 215C (419F)80C (176F)
(After Stall Test)If the value is º±40C (±40F)º or
º215C (419F)º, ATF temp. sen-
sor circuit is opened or shorted.
5. ACTIVE TEST
HINT:
Performing the ACTIVE TEST using the hand±held tester allows the relay, VSV, actuator and so on to oper-
ate without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one of the
methods to shorten the work time.
It is possible to display the DATA LIST during the ACTIVE TEST.
(a) Warm up the engine.
(b) Turn the ignition switch OFF.
(c) Connect the hand±held tester to the DLC3.
(d) Turn the ignition switch ON.
(e) According to the display on tester, perform the ºACTIVE TESTº.
ItemTest DetailsDiagnostic Note
LINE PRESS UP
[Test Details]
Operate the shift solenoid SLT and raise the line pressure.
[Vehicle Condition]
Vehicle Stopped.
IDL: ON
[Others]
ON: Line pressure up.
OFF: No action (normal operation)
±
LOCK UP
[Test Details]
Control the shift solenoid DSL to set the ATM to the lock±up condition.
[Vehicle Condition]
Vehicle Speed: 60 km/h (37 mph) or more
Possible to check the DSL opera-
tion.
SHIFT
[Test Details]
Operate the shift solenoid valve and set the each shift range by your-
self.
[Vehicle Condition]
Less than 50 km/h (31 mph)
[Others]
Press button: Shift up
Press button: Shift down
Possible to check the operation of
the shift solenoid values.
6. PROBLEM SYMPTOM CONFIRMATION
(a) Taking into consideration the results of the customer problem analysis, try to reproduce the symptoms
of the trouble. If the problem is that the transaxle does not shift up, shift down, or the shift point is too
high or too low, conduct the following road test referring to the automatic shift schedule and simulate
the problem symptoms.

Page 946 of 5135

TOYOTA AVENSIS 2005 Service Repair Manual ±
DIAGNOSTICS ELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT](U241E(1AZ±FSE))05±925
AVENSIS REPAIR MANUAL (RM1018E)
7.ROAD TEST
NOTICE:
Conduct the test at normal operating ATF temperature 50 to

±
DIAGNOSTICS ELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT](U241E(1AZ±FSE))05±925
AVENSIS REPAIR MANUAL (RM1018E)
7.ROAD TEST
NOTICE:
Conduct the test at normal operating ATF temperature 50 to 80 C (122 to 176 F).
(a)D range test Shift into the D range and fully depress the accelerator pedal and check\
the following points:
(1)Check up±shift operation.Check to see that 1 2, 2 3 and 3 O/D up±shift take place, and that the shift points conform
to the automatic shift schedule (See page 03±45).
HINT:
O/D Gear Up±shift Prohibition Control (1. Water temp. is 60 C (140 F) or less. 2. If there is a 10 km/h
(6 mph) difference between the set cruise control speed and vehicle speed.)
O/D Gear Lock±up Prohibition Control (1. Brake pedal is depressed. 2. Water temp. is 60 C (140 F)
or lower)
(2)Check for shift shock and slip. Check for shock and slip at the 1 2, 2 3 and 3 O/D up±shift.
(3)Check for abnormal noise and vibration.
Run in D range lock±up or O/D gear and check for abnormal noise and v\
ibration.
HINT:
The check for the cause of abnormal noise and vibration must be done very t\
horoughly as it could also be
sure to loss of balance in the differential, torque converter, etc. (4)Check kick±down operation.While running in the D range, 2nd, 3rd and O/D gears, check to see that the p\
ossible kick±down
vehicle speed limits for 2 1, 3 2 and O/D 3 kick±downs conform to those indicated in the
automatic shift schedule (See page 03±45).
(5) Check for abnormal shock and slip at kick±down.
(6) Check the lock±up mechanism.
Drive in D range O/D gear, at a steady speed (lock±up ON) of about 60 km/h (37 mph).
Lightly depress the accelerator pedal and check that the engine speed does not change
abruptly.
If there is a big jump in engine speed, there is no lock±up.
(b) S range test Shift to the S range, depress the accelerator pedal and check the follow\
ing points:
Shift operations.
Shifting the shift lever to º+º or º±º changes the shift \
range on the combination meter.
HINT:
Manual shift prohibition control is performed when:
The ATF temperature is low.
Down±shifting causes engine overrun.
Down±shifting is required continuously. (Down±shifting to 1st gear may not be performed.)
(c) R range test Shift into the R range and fully depress the accelerator pedal and check\
for slipping.
CAUTION:
Before conducting this test, ensure that the test area is free from peop\
le and obstruction.
(d) P range test Stop the vehicle on a grade (more than 5 ) and after shifting into the P range, release the parking
brake. Then, check to see that the parking lock pawl holds the vehicle in plac\
e.

Page 947 of 5135

TOYOTA AVENSIS 2005 Service Repair Manual D25148
TA CDLC3 12345 768
9 1 0111 21 3 1 514 16 05±926
± DIAGNOSTICSELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U241E(1AZ±FSE))
AVENSIS REPAIR MANUAL (RM1018E)
8. MECHANICAL SYSTEM TESTS
(a

Page 948 of 5135

TOYOTA AVENSIS 2005 Service Repair Manual D25148
TA C
12345 768
9 1 0111 21 3 1 514 16
± DIAGNOSTICSELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U241E(1AZ±FSE))05±927
AVENSIS REPAIR MANUAL (RM1018E)
(b) Measure the time lag.
(1) When

Page 949 of 5135

TOYOTA AVENSIS 2005 Service Repair Manual D25472
SST
SST
05±928± DIAGNOSTICSELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U241E(1AZ±FSE))
AVENSIS REPAIR MANUAL (RM1018E)
9. HYDRAULIC TEST
(a) Measure the line pressure.
NOT

Page 950 of 5135

TOYOTA AVENSIS 2005 Service Repair Manual D09299
± DIAGNOSTICSELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U241E(1AZ±FSE))05±929
AVENSIS REPAIR MANUAL (RM1018E)
10. MANUAL SHIFTING TEST
HINT:
By this test, it can be determined whethe

Page 951 of 5135

TOYOTA AVENSIS 2005 Service Repair Manual G23367
Tester menu flow: 05±930
± DIAGNOSTICSELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U241E(1AZ±FSE))
AVENSIS REPAIR MANUAL (RM1018E)
11. RESET MEMORY
CAUTION:
Perform the RESET MEMORY (A

Page 952 of 5135

TOYOTA AVENSIS 2005 Service Repair Manual 0567O±11
Transmission Control
System Check SheetInspector s
Name:
Customer s Name
Registration No.
Registration Year
Frame No.
Date Vehicle
Brought InOdometer Readingkm
mile / /
/

Load next 8 pages

Page: < prev 1-10 ... 913-920 921-928 929-936 937-944 945-952 953-960 961-968 969-976 977-984 ... 5136 next >

battery apple carplay turn signal key fob display ad blue